For use with 2-56 threaded rods. Smaller lighter weight version. Usually used on .25 size (3 pound) and smaller models. Package of 2 each. Item is right most unit in photo.
Comes with standard press on nylon and permanent steel press on retainer. Also equiped with socket head fastener to allow for tighter instalations. Drilled to clamp onto 2-56 and 2mm rods. This brass connector has hex head to allow you to hold it while tightening.
Comes with standard press on nylon and permanent steel press on retainer. Also equiped with socket head fastener to allow for tighter instalations. Drilled to clamp onto 2-56 and 2mm rods so common in ARFS.
Du-Bro E-Z Connector #121 for 2-56 Rod or Cable up to .078"
E/Z Connectors for up to .078 (2-56) pushrod or cable. 4-40 x 1/8 Slotted Screw locks pushrod or cable in place. Black snap on washer & push on steel retainer included. 2 units per package.
Bulk Pack contains 12 each. Comes with standard press on nylon and permanent steel press on retainer. Also equiped with socket head fastener to allow for tighter instalations. Drilled to clamp onto 2-56 and 2mm rods so common in ARFS.
1.5mm/2mm/2-56 EZ-A-Just Rod Ends up to 1.8mm shafts
Four barrels, washers, nuts and set screws. Allen wrench not included, requires 1.5mm. Will work on any rod size 1.5 to 1.85mm (.074"). 2mm pushrods and 2-56 are usually this size or smaller. The threads are rolled and larger than the base wire diameter. Instal in 5/64" (1.9mm) hole.
1.5mm/2mm/2-56 Heavy Duty EZ-A-Just Rod End up to 2mm Shafts
Four barrels, washers, nuts and set screws. Allen wrench not included, requires 1.5mm. Will work on any rod size 1.5 to 2mm (.079"). 2mm pushrods and 2-56 are usually this size or smaller. The threads are rolled and larger than the base wire diameter. Install in 7/64" (2.6mm) hole.
1/16" Brass Coupler to 2-56 threaded Ball Link and Ball Stud
Stud of ball is 0-80 thread with black nut. Perfect fit for most glow throttle arms pefectly. Bolt to control hors and servo horns also. Brass fitting fits and solders onto .062 (1/16") steel wire or pushrod cable. Nylon ball link also included.
Retains simple L bend pushrod ends in your control or servo horn. For .062 (1/16") wire. This is a common size music wire to use for hand built pushrods.
Easily snaps over simple L bends to retain your pushrod end in servo or control surface horn. For .072 wire size. .072 is the diameter of the untreaded portions of 2-56 prethreaded pusrods.
GWS rack of 6 L bend ratainers. Simply bend an "L" into the end of your wire, put the eyelet of this retainer over the L end then clip the base over the leg of your wire. Perfect solution for quick and easy pushrod ends.
2-56 Spring Steel Kwik-Links 12 Pack for .072 Wire
Solder onto .072 wire. Typical wire size that has 2-56 rolled threads on one end. Use to build your own custom length pushrods from music wire or "one-end" pre-threaded 2-56 rod. Link retaining sleeves included. Unit looks like left 2 items in sample photo.
Solder onto .072 wire. This is the typical size wire that has 2-56 rolled threads on one end. Use to build your own custom length pushrods from music wire or "one-end" pre-threaded 2-56 rod. Link retaining sleeves included. Unit looks like lcenter 2 items in sample photo.
Solder onto .072 wire. Typical wire size that has 2-56 rolled threads on one end. Use to build your own custom length pushrods from music wire or "one-end" pre-threaded 2-56 rod. Link retaining sleeves included. Unit looks like left 2 items in sample photo.
Solder onto .072 wire. This is the typical size wire that has 2-56 rolled threads on one end. Use to build your own custom length pushrods from music wire or "one-end" pre-threaded 2-56 rod. Link retaining sleeves included. Unit looks like lcenter 2 items in sample photo.
Four barrels, washers, nuts and set screws. Allen wrench not included, requires 1.5mm. Will work on any rod size 1.5 to 1.85mm (.074"). 2mm pushrods and 2-56 are usually this size or smaller. The threads are rolled and larger than the base wire diameter. Instal in 5/64" (1.9mm) hole.
Easily snaps over simple L bends to retain your pushrod end in servo or control surface horn. For .093 (2.5mm) wire size. .093 (2.5mm) is the diameter of the untreaded portions of 4-40 pusrods.
SKU Number: DUB885
NASA wants to go back to the moon. Radical RC's Wicked Wing beat them to it! Check out our original designs! Radical RC Verti-Go 125, Verti-Go 3D, E-Hornet, Mini Stick, Micro Stick, Micro Bipe, Micro Low Stick, Quick Wing 12mm, Quick Wing 20mm, Quick Wing Twin 20mm Double Trouble, Das Mini Low Stick, Das Mini Bipe, Mini Hunter, Mini Intern Trainer, Stick 600,
We cover all the basics on charging and cycling, and the receivers that we provide. PLEASE READ THIS PRIOR to sending any items back. 99% of all returned items test perfect. Learn how to check your cycler/charger or receiver here without spending money on postage.
Pictured to left is one of Garrett's competition ships, to right .... Dave, Here is a picture of my second plane. This is a 3W Extra 330 40%. The plane is flying great. Thanks so much for all your support in this hobby. I really like using your products. My friends as well are very happy with the equipment & fast-friendly service that is coming out of your company. Let's keep in touch. -Garrett Morrison
 "Mini Nylon Kwik Links 2-56")
 "2-56 Kwik Links Nylon 2 Pack")
 "2-56 Kwik Links Nylon Bulk Pack")
 "Kwik Grip E-Z Connector 2-56/2mm")
 "2-56 Safety Lock Kwik-Links")
 "Dubro Heavy Duty E-Z Connector 2-56/2mm")
![](javascript:largeIMTop('http://www.radicalrc.com/shop/images/102708-2485.jpg','http://www.radicalrc.com/shop/images/102708-2485.jpg',0,'102708',0,'Du-Bro E-Z Connector #121 for 2-56 Rod or Cable up to .078"') "Du-Bro E-Z Connector #121 for 2-56 Rod or Cable up to .078\"")
 "Kwik Grip E-Z Connector 2-56/2mm Bulk 12 Pack")
 "1.5mm/2mm/2-56 EZ-A-Just Rod Ends up to 1.8mm shafts")
 "1.5mm/2mm/2-56 Heavy Duty EZ-A-Just Rod End up to 2mm Shafts")
![](javascript:largeIMTop('http://www.radicalrc.com/shop/images/1-16-to-2-56-threaded-Ball-Link104680-4876.jpg','http://www.radicalrc.com/shop/images/1-16-to-2-56-threaded-Ball-Link104680-4876.jpg',0,'104680',0,'1/16" Brass Coupler to 2-56 threaded Ball Link and Ball Stud') "1/16\" Brass Coupler to 2-56 threaded Ball Link and Ball Stud")
 "2-56 Solder Kwik Links for .072Wire & Cable")
 "Mini E/Z Link L Bend Keeper for .062 Wire")
 "E/Z Link L Bend Keeper .072")
![](javascript:largeIMTop('http://www.radicalrc.com/shop/images/104002-3908.jpg','http://www.radicalrc.com/shop/images/104002-3908.jpg',0,'104002',0,'L Bend Retainers by GWS for .063" wire') "L Bend Retainers by GWS for .063\" wire")
 "2-56 Spring Steel Kwik-Links 12 Pack for .072 Wire")
 "2-56 Steel Kwik-Links 12 Pack for .072 Wire")
 "2-56 Spring Steel Kwik-Links 2 Pack for .072 Wire")
 "2-56 Steel Kwik-Links 2 Pack for .072 Wire")
 "Sullivan 2-56 Gold-N-Clevises")
 "Sullivan 2-56 Gold-N-Clevises Bulk Pack")
 "1.5mm/2mm/2-56 EZ-A-Just Rod End Connectors")
 "2-56 Nylon Clevises Bulk Pack Four Pi")
 "E/Z Link L Bend Keeper .093")
