1/32 aircraft ply small laser horns. Mounting surface area on these are idealy suited to models with 3/32 to 1/4" thick control surfaces. These horns have holes correct for 1/32 wire used in all the smallest servos such as GWS Pico/Naro, HS-50, PS-20. HE490, HE2003, MX30 and many others. kits. Install horns in a slot in surface, because of the large contact area, they won't wobble like plastic pin type horns do. This results in finer better control and fewer trim changes in flight. 8 horns per package.
1/32 aircraft ply small laser horns. Mounting surface area on these are idealy suited to models with 1/16 to 1/8" thick control surfaces. These horns have holes correct for 1/32 wire used in all the smallest servos such as GWS Pico/Naro, HS-50, PS-20. HE490, HE2003, MX30 and many others. kits. Install horns in a slot in surface, because of the large contact area, they won't wobble like plastic pin type horns do. This results in finer better control and fewer trim changes in flight. 8 horns per package. Same horns found in our Micro-Stick and Mini-Stick kits.
1/32 aircraft ply large laser horns. Large mounting surfase area on these are idealy suited to models with thick control surfaces like foamies. These horns have holes correct for 1/32 wire used in all the smallest servos such as GWS Pico/Naro, HS-50, PS-20. HE490, HE2003, MX30 and many others. kits. Install horns in a slot in surface, because of the large contact area, they won't wobble like plastic pin type horns do. This results in finer better control and fewer trim changes in flight. 8 horns per package.
Set of two control horns for control surfaces, aileron, flaps, elevator or rudder. Black nylon material. Mounting surface area on these are ideally suited to models with 3/32 to 1/4" thick control surfaces. Horn is mounted on 5-40 threaded bolt for adjustment of throw or surface travel. Includes diagram of installation instructions. Use on 25 to 60 size models.
Du-Bro Micro Adjustable Black Nylon Control Horn Set, 2PK
Lightweight, fully adjustable control horn for your indoor and park flyer models. Includes large area mounting plates with positioning points to prevent plates from turning. 1" long, 2-56 socket head post and horn. 2/pkg. (1.0 grams/ea.)
Two Pack, Du-Bro Micro2 Control Horn is 5/8" in height and is great for the larger scale micro aircraft. Horn has 2 pins on bottom for securing to surface.
New Du-Bro Micro Control Horn set. 1/2" working height/length. Molded pin on flat bottom for easy installation. After gluing, excess pin can be trimmed off. Great for indoor and park flyers! 2/pkg.
Set of five control horns, for control surfaces. Opaque fiberglass material. Precision cut. Mounting surface area on these are idealy suited to models with 3/32 to 1/4" thick control surfaces. These horns have holes correct for 1/32 wire commonly used in park fliers and F3P models. Note: 25mm size includes a backup plate. 5ea/pack. A nice, lightweight, durable product! Upper left hand in photo.
McDonough Small Laser Control Horns for .032" Wire
Tim McDonough's control horns come ten (10) to a package and are cut from 1/16 inch thick high quality aircraft plywood. Holes drilled for .032 wire. Can be enlarged to 2mm (use #51 .067 drill bit gently by hand) or 2-56 (use #50 .070" drill bit). Glue into your balsa / composite or foam surfaces.
Tim McDonough's control horns come ten (10) to a package and are cut from 1/16 inch thick high quality aircraft plywood. Holes drilled for nug fit on 2-56 wire .070"). Glue into your balsa / composite or foam surfaces.
Control horn has pins intended to be pressed into foam. Can be installed in balsa also. 22mm long, control radius 6mm. Note, control radius given if hinge line were at same surface as horn mounting. If you put this horn on 3mm material that is center hinged, your control radius would be +1.5mm. If hinged at opposite surface control radius would be +3mm. Material is .032 (.8mm) G10 fiberglass. 8 horns per package.
Control horn has pins intended to be pressed into foam. Can be installed in balsa also. 22.5mm long, control radius 6.5mm. Note, control radius given if hinge line were at same surface as horn mounting. If you put this horn on 3mm material that is center hinged, your control radius would be +1.5mm. If hinged at opposite surface control radius would be +3mm. Material is .032 (.8mm) G10 fiberglass. 8 horns per package.
Control horn has pins intended to be pressed into foam. Can be installed in balsa also. 23mm long, control radius 7mm. Note, control radius given if hinge line were at same surface as horn mounting. If you put this horn on 3mm material that is center hinged, your control radius would be +1.5mm. If hinged at opposite surface control radius would be +3mm. Material is .032 (.8mm) G10 fiberglass. 8 horns per package.
Custom designed for F3P competition aircraft and similar foamies. This set contains all the control horns, stand offs and transfer horns you can use on any one project. Control horns have long mounting leg that can be trimmed to fit your control surface/application. Control rod stand offs are included as are aileron transfer horns for the bipe enthusiasts.
We thank Seth Arnold for flying our F3P horn sets to victory at the 2009 ETOC. Designed in conjunction with Scott Barnhart.
The "Y" horn is for those that prefer a pull-pull rudder setup. Included is a set of 4 micro tension adjusters for your pull-pull lines. The adjusters allow you to loom up your lines like a tent line so you can adjust the tension of your control strings as weather and temperature demands.
Note the extra special Biased Servo Horn. This can be screwed or sewn to many common micro dual arm servo horns. Normally the aileron control horns are a bit farther apart than the spread of a stock servo horn. The Biased horn allows you to connect your aileron pushrod so that the rod is 90 degrees to the horn eliminating differential movement the stock horn would cause.
This package is sure to save you 2-3 hours of fiddly cutting, sanding and filing. ;-) Lets get busy and get some building done!
F3P Control Horn Set #2 in 1/32 Aircraft Ply. Features our professional biased servo horn (#1), Horns for Ailerons, horn for rudder with hinge line offset and elevator horn with both hinge line offset and notch to clear carbon stiffener strip. Designed in conjunction with Scott Barnhart.
Custom designed for F3P competition aircraft and similar foamies. This set contains all the control horns, stand offs and transfer horns you can use on any one project. Control horns have long mounting leg that can be trimmed to fit your control surface/application. Control rod stand offs are included as are aileron transfer horns for the bipe enthusiasts.
We thank Seth Arnold for flying our F3P horn sets to victory at the 2009 ETOC.
The "Y" horn is for those that prefer a pull-pull rudder setup. Included is a set of 4 micro tension adjusters for your pull-pull lines. The adjusters allow you to loom up your lines like a tent line so you can adjust the tension of your control strings as weather and temperature demands.
Note the extra special Biased Servo Horn. This can be screwed or sewn to many common micro dual arm servo horns. Normally the aileron control horns are a bit farther apart than the spread of a stock servo horn. The Biased horn allows you to connect your aileron pushrod so that the rod is 90 degrees to the horn eliminating differential movement the stock horn would cause.
This package is sure to save you 2-3 hours of fiddly cutting, sanding and filing. ;-) Lets get busy and get some building done!
Our F3P biased servo horn used by many top competition pilots. 4 peices per sheet. Control Radius .750" (Equivelant to 1.5" spread servo horn). 7 Holes are offset in 5 degree steps starting at 5 degrees and ending at 35 degrees. Holes are precision drilled at .031 to be snug zero slop fit to common .032 pin control rod fittings and music wire. May be sewn and glued to many standard horns. Laser cut from 1/32 aircraft grade plywood. Strong and light weight. I've never had a report of a broken horn. Same horn as provided in complete control horn sets above. Designed in conjunction with Scott Barnhart.
Our F3P biased servo horn used by many top competition pilots. 4 peices per sheet. Control Radius .750" (Equivelant to 1.5" spread servo horn). 7 Holes are offset in 5 degree steps starting at 5 degrees and ending at 35 degrees. Holes are precision drilled at .031 to be snug zero slop fit to common .032 pin control rod fittings and music wire. May be sewn and glued to many standard horns. Laser cut from .020 fiberlgass. Strong and light weight. I've never had a report of a broken horn. Same horn as provided in complete control horn sets above. Designed in conjunction with Scott Barnhart.
Our F3P biased servo horn used by many top competition pilots. 4 peices per sheet. Control Radius .625" (Equivelant to 1.25" spread servo horn). 6 Holes are offset in 6 degree steps starting at 5 degrees and ending at 35 degrees. Holes are precision drilled at .031 to be snug zero slop fit to common .032 pin control rod fittings and music wire. May be sewn and glued to many standard horns. Laser cut from 1/32 aircraft grade plywood. Strong and light weight. I've never had a report of a broken horn.
Our F3P biased servo horn used by many top competition pilots. 4 peices per sheet. Control Radius .625" (Equivelant to 1.25" spread servo horn). 6 Holes are offset in 6 degree steps starting at 5 degrees and ending at 35 degrees. Holes are precision drilled at .031 to be snug zero slop fit to common .032 pin control rod fittings and music wire. May be sewn and glued to many standard horns. Laser cut from .020 Fiberglass. Strong and light weight. I've never had a report of a broken horn. Designed in conjunction with Scott Barnhart.
8 each of our Micro Pull Pull Tension Adjusters. Alows you to loop your pull pull string through a horn then back to this adjuster which can be slipped and locked along the lenght of the cord running to the horn. Works like a tent pole rope adjuster. Use on F3P and other small models with pull-pull control functions. A very difficult part to make by hand simplified for you here.
FEATURES: Black plastic construction
Designed for medium size Park Flyers and indoor models
SKU Number: DUB936
NASA wants to go back to the moon. Radical RC's Wicked Wing beat them to it! Check out our original designs! Radical RC Verti-Go 125, Verti-Go 3D, E-Hornet, Mini Stick, Micro Stick, Micro Bipe, Micro Low Stick, Quick Wing 12mm, Quick Wing 20mm, Quick Wing Twin 20mm Double Trouble, Das Mini Low Stick, Das Mini Bipe, Mini Hunter, Mini Intern Trainer, Stick 600,
We cover all the basics on charging and cycling, and the receivers that we provide. PLEASE READ THIS PRIOR to sending any items back. 99% of all returned items test perfect. Learn how to check your cycler/charger or receiver here without spending money on postage.
Pictured to left is one of Garrett's competition ships, to right .... Dave, Here is a picture of my second plane. This is a 3W Extra 330 40%. The plane is flying great. Thanks so much for all your support in this hobby. I really like using your products. My friends as well are very happy with the equipment & fast-friendly service that is coming out of your company. Let's keep in touch. -Garrett Morrison
 "Small Laser Control Horns for 1/32 wire")
 "Medium Laser Control Horns 1/32 Wire")
 "Large Laser Control Horns 1/32 wire")
 "Du-Bro Adjustable Nylon Control Horn Set")
 "Du-Bro Micro Adjustable Black Nylon Control Horn Set, 2PK")
') "Du-Bro Micro2 Control Horn #919 (2 Pack)")
 "Du-Bro Micro Control Horn")
 "RRC Fiberglass 25mm Mini Control Horns")
![](javascript:largeIMTop('http://www.radicalrc.com/shop/images/103880-3752.jpg','http://www.radicalrc.com/shop/images/103880-3752.jpg',0,'103880',0,'McDonough Small Laser Control Horns for .032" Wire') "McDonough Small Laser Control Horns for .032\" Wire")
 "McDonough Small Laser Control Horns for 2-56 Wire")
 "RRC Surface Horn #1")
 "RRC Surface Horn #2")
 "RRC Surface Horn #3")
 "F3P Laser Control Horns Z Bend Set")
 "F3P Laser Horn Set Z-Bend #2")
 "F3P Laser Control Horns Z Bend Set .020 Fiberglass")
 "F3P Laser Control Horns Rod & Shrink Set")
 "F3P Laser Control Horns Rod & Shrink Set .020 Fiberglass")
 "F3P Biased Servo Horn #1")
 "F3P Biased Servo Horn #1 Fiberglass")
 "F3P Biased Servo Horn #2")
 "F3P Biased Servo Horn #2 Fiberglass")
 "Micro F3P Pull Pull Tension Adjuster Set")
') "Du-Bro Micro Razor Control Horns (2pk)")
