| |
Astro 3 Pin Zero Loss Connector (2 each)#521 Designed for 13 and 14 gauge wire. Zero Loss, same resistance as 13 gauge wire. Total reverse polarity protection. Note: This connector assembly uses female pins, the shell is male, therefore gendered as "male assembly". Specifications: Stock Number p/n 521 Maximum Continuous Amps 50 amps 2 minute rating 75 amps Maximum Wire size 13 gauge Minimum wire size 18 gauge Pin /Socket Diameter 2.5 mm Plating gold Length of pair 1.25 Inches Width 0.80 inches Weight 10 grams WHILE SUPPLIES LAST SKU Number: AST521
|
|
|
| |
Astro Micro 010 motor 10T This is a new motor and is designed to replace the 14 turn motor 6-12 volts, 10 a max, max amp one min 15 a, deans 3 pin motor connector and deans 2 pin power connector. WHILE SUPPLIES LAST SKU Number: AST801L10T
|
|
|
| |
Astro Micro Gear Box #709 Fits Astro 010 motors. The New Astro Micro Box for the Astro 010 brushless motor weighs only 1/2 ounce and fits all Astro 010 motors. The Gear ratio is 3.3 to 1 and it spins props from 8x6 to 10x7 on 8 to 10 NIMH cells or 2 to 3 lithium poly cells. The Gear Box is mounted to the motor with two screws and is mounted to the model with a single nut on the threaded barrel of the bearing housing right behind prop. Nothing could be simpler! The motor in this photo is for illustration only and is not included at this price. WHILE SUPPLIES LAST SKU Number: AST709
|
|
|
| |
Fromeco Badger High Output Failsafe with Slide Switch. Badger switch with aluminum face plate. Polishable to a crome finish by end user. Comes complete with charging jack, slide switch, and matching mounting fasteners. Rated at 15amps continuous current with spikes much higher. Built in charge jack in face of switch plate. Same footprint as the "Cermark" style switches for existing mounting holes. Amass "Deans Ultra compatible" connectors on input and output. This product comes to us preassembled. Last one left! SKU Number: FRMBADGER01D
|
|
|
| |
New in box. A rare turn count new old stock motor and esc system from Astro flight. If I remember correctly I ordered these special back in the day. Found hidden in inventory. Snag one of the coolest Astro brushless park flier motors every made.
Astro Flight Mighty Micro 010 Planetary System. Complete System includes Mighty Micro 010 fourteen turn Motor, 4.4 to 1 Planetary gear box and 10 amp speed control. Specifications: Gear Ratio: 4.4 to 1 Winding: 14 turns #24 Motor Diameter: 0.98 inches Length: 1.50 inches Prop shaft diameter: 3 mm Electronic Control: Sensorless, 10 amps, BEC 5 Volts @ 1 amp, Auto Lipo Cutoff Cells: 6 to 10 cells NiMH/NiCad / 2-3 Lipo, Fully Connectored Motor Constants: RPM/volt: 2,300KV, Resistance: .275 ohms, No load current: .3A. Max Constant Apms: 7.5 Expected Performance on 10 x 4.7 slow fly prop Battery Amps Watts Rpm 2 Lithium 2.6 amps 20 watts 3,600 rpm 8 Nimh 3.2 amps 28 watts 4,000 rpm 3 Lithium 4.6 amps 52 watts 4,800 rpm 10 Nimh 5.0 amps 61 watts 5,000 rpm Expected Performance on 11 x 4.7 slow fly prop Battery Amps Watts Rpm 2 Lithium 3.4 amps 26 watts 3,300 rpm 8 Nimh 4.1 amps 36 watts 3,700 rpm 3 Lithium 4.6 amps 63 watts 4,400 rpm 10 Nimh 6.4 amps 77 watts 4,600 rpm Expected Performance with 11 x 7 APC-E prop Battery Amps Watts Rpm 2 Lithium 3.4 amps 26 watts 3,300 rpm 8 Nimh 4.0 amps 36 watts 3,700 rpm 3 Lithium 5.6 amps 62 watts 4,400 rpm 10 Nimh 6.2 amps 74 watts 4,700 rpm Expected Performance with 12 x 6 APC-E prop Battery Amps Watts Rpm 2 Lithium 3.4 amps 26 watts 3,300 rpm 8 Nimh 4.0 amps 36 watts 3,700 rpm 3 Lithium 5.7 amps 62 watts 4,300 rpm 10 Nimh 6.4 amps 76 watts 4,500 rpm NEW IN SHELF-WORN BOX, LAST ONE LEFT, NON-WARRANTY, SALE IS FINAL SKU Number: AST801P-14T
|
|
|
| |
Astro Micro 020 motor 5 turns with 3.3:1 Gearbox. Included speed control, Zero Loss plugs on input and between ESC and motor. Specifications: Weight | Can Size D x L | Amps | Rated Max Watts | Shaft | Max Motor RPM | KV | Resistance | No Load Current | 104.9g/3.7oz. | .98"(24.8mm) x 3.1"(78.6mm) to drive plate | 18-25A, 30/30s | Not Pub. | Motor 1/8" Gearbox 1/4"(6.35mm) | 40k | 2567 | 7.5mOhm | 1A | Setup and Performance Chart # Cells | Prop | Amps | Watts Input | Lost Watts (Heat) | % Motor Efficiency | RPM | Static Thrust Ounces | Pitch Speed MPH | 2 | 14x10 | 23.9 | 179 | 48 | 70% | 3,880 | 30 | 37 | 3 | 11x7 | 20.6 | 232 | 41 | 81% | 6,950 | 37 | 46 | 3 | 11x10 | 25.6 | 288 | 58 | 78% | 6,510 | 37 | 62 | 3 | 12x8 | 27.5 | 309 | 65 | 77% | 6,340 | 44 | 48 | 4 | 10x6 | 22.7 | 341 | 51 | 84% | 9,550 | 47 | 54 | 4 | 10x8 | 27.4 | 411 | 68 | 82% | 9,110 | 49 | 69 | 4 | 11x5.5 | 27.7 | 413 | 68 | 82% | 9,010 | 56 | 47 | 5 | 9x4.5 | 19.7 | 369 | 45 | 87% | 12,630 | 49 | 54 | Estimates based on manufacturers provided constants using E-Calc. 1300 used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables.
WHILE SUPPLIES LAST SKU Number: AST803GM
|
|
|
| |
Adapter, Polarity Reverser for JR/ Spektrum Tx. Makes your Futaba/Hitec output from your Sirius charger or from your Futaba TX charge cord or Wall wart reverse polarity suitable for charging your JR TX. Sirius/Peak Electronics Inc. Warranty Info. DISCONTINUED BY MANUFACTURER, WHILE SUPPLIES LAST, SALE IS FINAL SKU Number: SIRADPJR
|
|
|
| |
This adaptor mates the Astro Blinky Balancer to Cell Pro 3S lithium battery packs. WHILE SUPPLIES LAST SKU Number: AST549CP
|
|
|
| |
Adapter, Charge Rx from Tx side of Sirius brand charger. Use with Sirius Pro/ Pro-Plus/ Multi Port chargers. Also, use to charge a TX pack that has a Futaba J or Universal Z type male plug from a Futaba TX wall wart type charger. DISCONTINUED BY MANUFACTURER, WHILE SUPPLIES LAST, SALE IS FINAL SKU Number: SIRADTXRX
|
|
|
| |
Adapter, Polarity Reverser for JR/Specktrum TX. Makes your Futaba/Hitec output from your Sirius charger or from your Futaba TX charge cord reverse polarity for your JR/Spektrum TX. Can be used with anything that has a standard Futaba TX output. DISCONTINUED BY MANUFACTURER, WHILE SUPPLIES LAST, SALE IS FINAL SKU Number: SIRADTXJR
|
|
|
| |
RRC-1000, 2/3A type cell. Exact same size as 600 Nicad with more capacity. At this price, this is an AS-IS deal. No crybabies - No returns. We only have about 10 of these on hand at time of these listing. SORRY, SOLD OUT SKU Number: RRC08N1000TIG
|
|
|
| |
Astro Micro 010 motor 8T This is a new motor and is designed to replace the 14 turn motor 6-12 volts, 10 a max, max amp one min 15 a, deans 3 pin motor connector on motor. This is the short version of the motor. Specifications: Stator Winding: 8 Turns Rpm/Volt: 3200KV Winding Resistance: 0.156 ohms No Load Current: .3amp Max Amps: 15 amps Max Power: 150 watts Size: 1.3" L, .098 D Weigh:t 56 grams Setup and Performance Chart # Cells | Prop | Amps | Watts Input | RPM | Static Thrust oz. | Pitch Speed MPH | 2 | 10x8 | 10.3 | 77 | 5,070 | 16 | 37 | 2 | 11x8 | 12.4 | 92 | 4,630 | 19 | 34 | 3 | 10x4.7 | 13.6 | 152 | 7,700 | 28 | 33 | 3 | 9x7 | 13.5 | 151 | 7,720 | 25 | 50 | 3 | 8x6 | 9.2 | 103 | 8,710 | 19 | 48 | 4 | 8x4 | 10.9 | 162 | 11,700 | 28 | 42 | 4 | 8x6 | 14.2 | 211 | 10,870 | 31 | 60 | Estimates based on manufacturers provided constants using E-Calc. High Quality 1300 used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables. NEW IN SHELF-WORN BOX, LAST ONE LEFT, NON-WARRANTY, SALE IS FINAL SKU Number: AST801GM08T
|
|
|
| |
Fiberglass Cloth has found many valuable uses in the model field. It is excellent for reinforcing critical strength areas of a model airplane such as the firewall attachment, wing center section, and landing gear installation. Model boat builders also like it for covering the bottom of a wooden boat hull for extra strength and puncture resistance. Polyester Glass Resin or slow-drying Epoxy Glue should be used to saturate the Glass Cloth and adhere it to the model structure. Glass Cloth and resin can also be used to mold entire model parts, such as a whole airplane fuselage. Cowlings, wheel pants, and any other model parts that have a lot of compound curves are also especially suited to fiberglass construction. Fiberglass parts such as these will have an outstanding strength-to-weight ratio and excellent dimensional stability. Lastly, many modelers like to use the ultra-light weight Glass Cloth as a covering material for their entire model, especially when an epoxy or enamel paint is going to be used. It's super strong and goes around compound corners with ease. Like the name implies, Glass Cloth is made of actual glass! First, very fine filaments of pure glass are spun into yarn. This yarn is then woven into varying weights of cloth. Glass is one of the strongest textile fibers, having greater tensile strength than steel wire of the same diameter. We have Glass Cloth available in four different weights to suit all possible modeling applications. Chemically treated to enhance glue/resin adhesion. This is the finest grade Glass Cloth available, manufactured by the largest fiberglass producer in the U.S. DISCONTINUED BY SIG, WHILE SUPPLIES LAST... SKU Number: SIGGF002
|
|
|
| |
Fiberglass Cloth has found many valuable uses in the model field. It is excellent for reinforcing critical strength areas of a model airplane such as the firewall attachment, wing center section, and landing gear installation. Model boat builders also like it for covering the bottom of a wooden boat hull for extra strength and puncture resistance. Polyester Glass Resin or slow-drying Epoxy Glue should be used to saturate the Glass Cloth and adhere it to the model structure. Glass Cloth and resin can also be used to mold entire model parts, such as a whole airplane fuselage. Cowlings, wheel pants, and any other model parts that have a lot of compound curves are also especially suited to fiberglass construction. Fiberglass parts such as these will have an outstanding strength-to-weight ratio and excellent dimensional stability. Lastly, many modelers like to use the ultra-light weight Glass Cloth as a covering material for their entire model, especially when an epoxy or enamel paint is going to be used. It's super strong and goes around compound corners with ease. Like the name implies, Glass Cloth is made of actual glass! First, very fine filaments of pure glass are spun into yarn. This yarn is then woven into varying weights of cloth. Glass is one of the strongest textile fibers, having greater tensile strength than steel wire of the same diameter. We have Glass Cloth available in four different weights to suit all possible modeling applications. Chemically treated to enhance glue/resin adhesion. This is the finest grade Glass Cloth available, manufactured by the largest fiberglass producer in the U.S. DISCONTINUED BY SIG, WHILE SUPPLIES LAST... SKU Number: SIGGF006
|
|
|
| |
APC LP07475C Sport Prop 7.4 x 7.5C
Q40 Carbon DISCONTINUED BY APC, LIMITED INVENTORY, WHILE SUPPLIES LAST SKU Number: APC07475C
|
|
|
| |
The Sig Cub was designed to be a simple, but capable, "advanced trainer" for modelers learning the ins and outs of trimming a F/F model. This little gem is capable of long high flights, limited only by the developing flier's knowledge. Kit Features: Die-cut Balsa Parts, Molded Plastic Propeller, Molded Plastic Wheels, SIG Contest Rubber Motor, Covering Material, Detailed Building And Flying Instructions & Detailed Full-Size Plans. SORRY, SOLD OUT SKU Number: SIGFF1
|
|
|
| |
When Hall of Fame modeler Frank Ehling set out to design a simple little rubber power model that AMA could use to introduce newcomers to the hobby, he probably never thought he was drawing up the most popular model airplane of all time. This is the same model that has been used since 1968 in beginner's promotions around the world. Very easy to build, yet can turn in some amazing flights. Perfect for a group build. Kit Features: A Ready-To-Use One-Piece Balsa Stick Fuselage. Printed Covering Material On Which The Wings And Tail Surfaces Are Constructed. A Ready-To-Use Molded Plastic Propeller Assembly. SIG Contest Rubber Motor. Detailed Building And Flying Instructions. The Kit Includes Everything Except The Glue! SORRY, SOLD OUT SKU Number: SIGFF5
|
|
|
| |
The full-size Monocoupe was always known for its exceptional flight performance. Tom Stark's model of this classic lightplane has proved to be a winner from its first test flight. Now you can duplicate this little beauty for your own enjoyment. 1973 Nationals Winner. Includes Sig contest rubber, die cut balsa parts, covering material, wheels, prop, instructions, plans with isometric views and full set of decals. Wingspan: 24" Lenght: 16" Potential for electric conversion with today's modern micro gear. SORRY, SOLD OUT SKU Number: SIGFF25
|
|
|
|