3S K6 Series 4000. 65C (260 Amps) Constant 130C (520 Amps) Burst. High discharge cells. Industry Standard XH balance plug. Weight: 390 grams Measures: 141 x 49 x 26mm
All controls have Latest Software onboard! The Phoenix-25 ESC available in aircraft and helicopter versions and is ideal for Most Mid sized outrunners 400 size and smaller. Astro 020, Astro 05, Aveox 1005, Jeti Phasor (under 25 amps) and Hacker BL-20 and BL-40 motor applications. Cells w/ BEC 5-10 or 2-3 Lipo Cells w/o BEC 5-16 or 2-5 Lipo Continuous 25 Amps Surge 40 Amps Switching Rate 7,000 Hz Resistance 0.0065 Ohms Brake yes, programmable Reversible yes - change any two wires Size 1.08 x 0.91 x 0.16 in. Weight (w/wires) 0.7 oz. (17g) Universal connector
This monster was created as a replacement for the YS170, Plattenberg Evo 30-10 class motors so common in pattern competition today. However, it has MANY more uses. All Himax motors come equipped with Japanese bearings, so no replacing them right out of the gate like most of the other brands.
Specifications:
Weight
Size D x L
Amps
Shaft
Max Motor RPM
KV
Resistance
No Load Current
575g/20.28oz.
63mm(2.48") x 67mm(2.48")
20-75, 80 15s
8.0mm (.315")
10k
210
.022Rm
1.5A
Setup and Performance Chart
# Cells
Prop
Amps
Watts Input
RPM
Static Thrust oz.
Pitch Speed MPH
8
25x12.5
86.7
2367
4,170
286
49
8
20x12
58.1
1813
5,420
234
61
8
22x12
74.7
2331
5090
283
57
10
18x12
60.5
2360
6,830
270
76
10
20x12
80.2
31.28
6390
338
71
10
22x10
90.4
3526
6,160
371
57
12
16x12
57
2668
8380
271
94
12
18x12
87
3693
7,820
358
87
14
16x12
71.8
3920
9430
345
105
14
18x10
86.7
4734
9,010
424
84
16
16x8
65.3
4075
11,060
367
82
Estimates based on manufacturers provided constants using E-Calc. High quality 3200 used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables. SKU Number: MPIHC6330PRO
4 oz tank measurements: 1 1/2 H x 2 1/16 W x 3 3/4 Long. Du-Bro Fuel Tanks are designed to be tough! Our fuel tanks will not split or crack from vibration or pressure. In fact, our fuel tanks can be used with pressurized fuel systems! Comes complete with clunk line, clunk, brass tubes and stopper, cap and fastener.
The DU-BRO Fuel Tanks are known throughout the RC hobby for their incredible strength, reliability, and long service life. With over 30 years of 0% tank failure, these tanks have earned a reputation as some of the toughest and most dependable in the industry.
DU-BRO fuel tanks are designed to resist cracking, splitting, and deformation from vibration or engine pressure. They are even strong enough to work with pressurized fuel systems, making them a trusted choice for both sport and high-performance models.
Each tank comes complete with high-quality hardware, including DU-BRO's famous one-piece clunk, which features built-in fuel barbs to prevent fuel tubing from slipping off. This ensures a secure, leak-free connection and smooth fuel delivery during flight.
You can use DU-BRO fuel tanks with glow fuel or gasoline. All you need for gas use is the #400 Gasoline Conversion Stopper, unless you are using one of these tank series:
#690-#692 - Includes tubing and stoppers for both glow and gasoline
#795-#797 - Pre-configured specifically for gasoline use
Each tank's capacity is approximate and may vary slightly. Also note:
2 oz and 4 oz tanks do not have the protruding lip
All larger sizes do include the molded lip for secure mounting
These tanks are perfect for RC airplanes, boats, and other models that require a strong, worry-free fuel system. They are easy to install, long-lasting, and built to handle the demands of everyday flying.
Tubing:
2-24 oz. Tanks include 3/32" I.D. silicone tubing. For gasoline, purchase 3/32" I.D. Tygon tubing (not included)
32-100 oz. Tanks include 1/8" I.D. silicone and Tygon tubing for gasoline or nitro fuel.
Proudly Made in the USA, DU-BRO Fuel Tanks continue to set the standard for reliability, durability, and performance in RC fuel systems.
Second from left motor in photo is the 3516 series.
Himax 3516 series motors are most generally used in 34-70 oz models depending on application. Replaces AXI 28 series motors. Manufactured to high standards for the discerning modeler. Package includes collet type prop adapter, prop saver, bullet females for your ESC and fasteners.
Specifications:
Weight
Size D x L
Amps
Shaft
Max Motor RPM
KV
Resistance
No Load Current
134g/4.7oz.
35.2mm(1.39") x 42.2mm(1.66")
15-40,56 15s
5.0mm (.1969")
20k
1350
.023Rm
2.3A
Setup and Performance Chart
# Cells
Prop
Amps
Watts In
RPM
Thrust oz.
Pitch Speed MPH
2
10x10
26
195
7,710
29
62
2
12x10
39.4
296
5,800
42
54
3
8x6
28.2
317
12,880
42
71
3
9x4.5
31.7
357
12,600
50
51
3
9x6
38.5
433
12,040
56
66
3
9x9
49.4
556
11,150
54
98
3
10x5
44.4
500
11,560
65
53
3
10x7
54.1
609
10,770
70
69
3
11x5.5
58
653
10,450
78
52
4
8x4
32.7
491
17,250
60
62
4
8x6
43.5
653
16,260
68
89
4
9x4.5
48.5
728
15,800
82
64
5
7x6
42.5
797
20,980*
70
115
Estimates based on manufacturers provided constants using E-Calc. High Quality 2200mah used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables. * Over reccomended maximum RPM. SKU Number: MPIHC35161350
Actual KV here measured in our shop is 1207. Motors like this mostly commonly used 3S for sport ship range where moderate to high pitch speeds are required. A motor like this is perfect for many aircraft and commonly used on models from 16-32 oz. A good motor on our Stick 400 and other similar kits.
Specifications As Per MFG:
Weight
Size D x L
Amps
Shaft
Max Motor RPM
KV
Resistance
No Load Current
73g/2.72oz.
27.7mm (1.102") x 35.86mm (1.412")
25.4A (368 watt)
4mm (.159") x 44.9mm OAL
Non-Pub
Actual 1478
Non-Pub
Non-Pub
Setup and Performance Chart
# Cells
Prop
Amps
Watts Input
Lost Watts (Heat)
% Motor Efficiency
RPM
Static Thrust Ounces
Pitch Speed MPH
2
9x7
23.5
176
40
75%
8,150
24
54
2
10x6
27.1
203
50
73%
7,670
28
44
3
7x6
21.4
241
39
82%
13,810
27
78
3
8x4
23.3
262
44
82%
13,540
31
51
3
8x6
29.8
335
63
79%
12,610
37
72
4
6x5.5
20.7
311
43
85%
19,300
30
101
4
7x4
25.5
383
55
84%
18,650
42
70
4
7x5
29.5
443
67
83%
17,940
45
85
5
6x4
23.5
441
55
87%
24,230
43
92
Estimates based on manufacturers provided constants using E-Calc. High Quality 2200mah used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables.
Side By Side 9.6V AA-700 NiCad. Yes, it is the same size as your current AA pack. A "AA" is a "AA". Slightly higher capacity than man factory packs (600mAh is typical). Also fits Futaba FG radios with gold cases. In the Futaba case the pack appears to have 9 cells but one is a hollow dummy cell. This pack fits just fine and is correct voltage.
Maintenance charge and maximum form charge rate for this pack is not to exceed 70mAh. See chart at top of category page for charging recommendations.
Form charge on factory wall charger only, not to exceed 70mAh. Attempting to form charge (initial charge) on peak detection charger or by any other method not specifically stated here is not recommended and voids warranty.
These motors are for large models weighing 4.8-5.8Lb for 3-D flight, up to 9.5Lb for aerobatic flight and 14Lb for leisure flight.
HC50 Outrunners generally used from 800-1500 Watts. High torque to turn large props direct drive. Replaces .40-.60 size engines. Mounting hardware and connectors included. Himax Brushless motors are manufactured to high standards for the discerning modler. Designed for light-weight, high efficiency, high torque and durability Himax Outrunner motors are sure to make todays radio controlled models perform.
All HC50 series outrunner motors include: Prop adapter, female wire connectors, motor mounting kit w/screws and two hex keys. Also included is base for standoff motor mount kit ACC3650 sold seperately.
Specifications:
Weight
Size D x L
Amps
Shaft
Max Motor RPM
KV
Resistance
No Load Current
275g/9.7oz.
48.8mm(1.96") x 53.2mm(2.09")
30-50, 65 15s
6.0mm (.2362")
12k
530
.033Rm
1.8A
Setup and Performance Chart
# Cells
Prop
Amps
Watts In
RPM
Thrust oz.
Pitch Speed MPH
3
16x10
36.7
413
4,590
76
43
3
18x12
52.7
593
3,990
95
45
4
14x10
40.1
603
6,290
91
58
4
15x10
47.6
714
5,980
105
56
4
16x12
60.8
912
5,440
119
61
5
12x12
42.5
793
8,020
89
90
5
13x10
46.2
866
7,840
111
73
5
14x7
44.2
829
7,930
119
51
5
15x10
64.6
1211
7,010
147
65
6
12x12
55.2
1242
9,020
118
103
6
14x7
57.5
1294
9,090
158
59
6
15x7
67.4
1517
8,600
177
69
7
12x8
53
1391
11,090
153
82
7
13x6.5
56.8
1491
10,890
170
65
8
11x10
59.5
1785
12,490
153
116
Estimates based on manufacturers provided constants using E-Calc. High Quality 3200mah used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables. SKU Number: MPIHC50180530
Slow Stick Canard made easy! This all-in-one unit will mount your horizontal stab and allow angle of attack adjustments to suit your special setups. Most canards should be set to between 3 and 5 degrees positive. Range of adjust ment is from 0 to 7 degrees positive. Elevator servo moves with the canard mounting surface so your elevator adjustment stays the same relative to your canard when you alter the angle of attack setting. Mount has built in nose gear block and nose gear steering servo mount. All holes are predrilled. Includes high quality socket head hardware needed to complete.
My personal Slow Stick Canard is a twin tractor. I have a 1000mm boom length and the CG is set at 1-1.25" in ffront of the main wing leading edge. I have never built one with a stock boom length (800mm) but I would start with the CG in the range of 0-.5" in front of the leading edge. The shorter the boom the further the CG comes back, the longer the further forward you would place it. I don't know where Bob Masterson's CG is set but I would thing it is similar to my 1000mm boom setup.
Maiden Flight Video of Bob Masterson's converted Canard Slow Stick. This model is full house with 10" extended boom length.
Himax Brushless motors are manufactured to high standards for the discerning modler. Designed for light-weight, high efficiency and durability of todays performance. Select ESC Combo below.
Specifications/Constants:
Weight
OD x Lengths
Max Efficient
Shaft
Max Motor RPM
KV
Resistance
No Load Current
65g(2.3oz)
20mm (.79") x 42mm (1.68")
10-20A
2.0mm(.078")
60k
4200
.075Rm
.75A
Setup and Performance Chart
# Cells
Prop
Amps
Watts In
RPM
Thrust oz.
Pitch Speed MPH
2
4.1x4.1
15.8
119
24,330
12
94
2
4.7x4.2
21.9
164
21,670
16
86
2
5x3
20.9
157
22,100
18
63
3
4.2x2
20
225
37,490
23
73
Estimates based on manufacturers provided constants using E-Calc. High Quality 500mah used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables.
This FDK (formerly Sanyo) AA 1650 Multiplex pack is the only way to go when replacing your weak factory pack. 7.2 volts and 6 cells just more bang. Comes without plug, reuse your old plug, direct solder or select optional Multiplex transmitter connector below. No thermal fuse in these packs.
Maintenance charge and maximum form charge rate for this pack is not to exceed 100mah. See chart at top of category page for charging recommendations.
Form charge on factory wall charger only, not to exceed 100mah. Attempting to form charge (initial charge) on peak detection charger or by any other method not specifically stated here is not recommended and voids warranty.
Maxx Products Light Weight Motor Mount, small size. Fits most outrunners smaller than 28mm like Himax 22 series and etc. Fits most 20mm inrunners. Injection molded part. Stands motor out 2.65" (67.3mm). SKU Number: MPIACC3952
A123/LithiumWerks' High Performance Nanophospate lithium iron phosphate (LiFePO4) battery technology delivers high power and energy density combined with excellent performance and extensive life cycling in a lighter weight, more compact package. A123LithiumWerks' cells have a low capacity loss and impedance growth over time as well as high usable energy over a wide state of charge (SOC) range, allowing out them to meet requirements of many applications.
These batteries are capable of 50 amp constant discharge, with a 10 second pulse rating of 120 amps. Cycle up to 1000 times before significant capacity loss occurs. The rugged assembly of the products will ensure that your pack will last for years, not months. Can be repeatably charged to 100% in 15 minutes. Charge only with Lithium chargers with an A123 (LIFE) mode limiting charge voltage to 3.6V per cell.
Specifications, March 2021:
Nominal Ratings Voltage 3.3 V Capacity @ 25 °C 2.56 Ah +/- 0.1 Ah Energy @ 25 °C 8.25 Wh Specific Power @ 25 °C, 2 sec pulse > 4000 W/kg Impedance (1KHz AC) Typical 6 mΩ Cycle Life at 1C/1C, 100% DOD > 4000 cycles
Discharging Max Continuous Discharge Current 50 A (20C rate) Max Pulse Discharge Current (10s) 120 A (48C rate) Minimum Voltage / HPPC Pulse 2 V / 1.6 V Temperature -30 °C to 60 °C
Charging: Charge only with Lithium chargers with an A123 (LIFE) mode limiting charge voltage to 3.6V per cell:
Cell charging parameters: CC-CV (constant current - constant voltage) Recommended Charge Current 3 A (1.2C rate) Max Continuous Charge Current 10 A (4C rate) Max Pulse Charge Current (10s) 20 A (8C rate) Float Voltage 3.45 V Recommended charge V & Cut-off Current 3.6 V, taper to 125mA
Temperature Range (reduce charging current to 250mA when under 0 °C) -20 °C to 60 °C
Storage Storage Temperature -40 °C to 70 °C
Mechanical Diameter Ø25.96 +/- 0.5 mm Length 65.15 +/- 0.5 mm Mass 76 g +/- 1.0 g
Tech Notes: 10A Recommended float charge and storage voltage: 3.8V Recommended cut-off current for CV hold: 0.05A Maximum continuous charge current: 10A Maximum allowable charge voltage: 4.2V MAX Fast charge time: 15 minutes Cell discharging parameters: Recommended discharge cut-off voltage: 2.0V Maximum continuous discharge current: 50A Cell temperature parameters (skin temperature) Maximum recommended cell temperature: (158F) Maximum allowable cell temperature: (185F)
ULTRA-HIGH POWER LITHIUM-ION CELL, 2800mAh, Multi-Cell Pack
INR18650-P28A
Molicel has dedicated our product development in the path of ultra-high power cells with focus.
[EDITS PENDING: The launch of a new generation 18650 power cell, INR-18650-P28A, featuring 7% higher capacity however 22% lower DCR compared to P42A. Its consistent 45A discharging performance has now enhanced hugely with superior fast charge capability up to 3C charging rate.]
This is a starting point of low impedance version that shall be ideal for premium segment in EV, eVTOL, micro-mobility, home appliances and more applications.
Single Cell is in last photo.
Molicel Battery - Ultra-high Power Cell INR18650-P28A
Charge Current: Recommended: 2.8 A (1C); Maximum: 6.0 A (3C)
Discharge Current: Continuous (MAX): 35 A
Dimensions: Diameter: 18.6mm X Length: 65.2mm
Weight: 46g
Power Output: 184W (10s, SOC 90%); 168W (10s, SOC 50%)
Energy Density: 610 Wh/l; 240 Wh/kg
ABOUT ADVANCED R&D PRODUCTS & APPLICATIONS bolt Up to 120W Higher retention for discharge energy up to 120W continuously loop 500+ Cycles High rate 80% retention electrical_services Fast Charge 13.5A continues charge south_west Lowest DCIR Max internal resistance 13.8 mOhm trending_down Low Impedance Growth Over long cycle thermostat Thermal Controlling In cell thermal distribution optimized (3-4 ?C)
Choose your custom pack from the options below, if there's a plug and wire combination not listed, type in your request in the box provide below the options. Photos depict wire configuration options, want something different, type in your request in the box provided below the options.
Please indicate # Cells x # Cells and other notes in the "Battery Pack Shape Notes" box below, then in the Comments section at checkout tell us you're sending us a drawing, diagram, or photo.
Some helpful shape descriptions:
Square: # Cells High x # Cells High, Even # Cells, looks like two cells on top of two cells from end view.
Block: # Cells Flat Wide x # Cells Flat High
Block Offset/Nested: # Cells Flat Wide x # Cells Flat High Offset/Nested
Double Stick: # Cells End to End beside # Cells End to End, "Shotgun barrel style"
Triangle: 3 Cells in a triangle (1 cell nested on top of 2 cells)
Triple Stick Triangle: 2 Sticks of #Cells End to End + 1 Stick of # Cells High Nested, multiples of 3 Cells
Triple Stick Flat: 3 Sticks # Cells x # Cells Flat, multiples of 3 Cells
Quad Stick Offset/Nested: # Cells per Stick, 2 Sticks Wide x 2 Sticks High, Offset/Nested, Even Cell Counts
Capable of big sky flying or ball park low-n-slow! You can trust the Quick Wing in any flight condition. Any 20mm brushless motor system capable of turning a 4-6" prop at 50-150 watts or more will work well. She is sure to please the most speed hungry wing fanatic while still retaining very good slow speed handling characteristics. Quick "3D Jigsaw Puzzle" assembly in only 1-2 hours. World class laser cutting and design make this one of the quickest and most enjoyable balsa models you will ever build. You'll be amazed at the wide speed envelope the Quick Wing has. It easily goes from high speed to ball park flying with no bad habits. I'm totally comfortable recommending this kit as a good 2nd or 3rd model as long as you keep the power system modest. Advanced pilots can take the power as far as they like.
Specs: Wing Span 22.25" Wing Area 195 sq. in. Weight 8.5-14oz. Length 13.75" Average Cord 9.75"
Required: Covering;3ch+ Radio with elevon mixing; RX;2 Micro servos (HS-55 or similar); 50-200 watt 20mm motor; Prop; 700-1800mah+/- 2S-3S LiPB; ESC. If you select a receiver (RX), tell us which channel you need at checkout.
The HS-485HB updates the very popular HS-475HB by adding more torque and greater speed. With its top ball bearing, heavy duty, high impact Karbonite gears and high performance circuitry, the HS-485HB offers lots of torque and features excellent centering and resolution.
6S K6 Series 3800mAh 65C (247 Amps) Constant 130C (494 Amps) Burst. High discharge cells. Industry Standard XH balance plug. Weight: 640 grams. Measures: 44H x 48W x 140mm L. SKU Number: KYP6S3800HD65C
The new Sig Somethin' Extra has it all - good looks, incredible performance, Sig quality balsa and ply construction and every part in the kit is laser-cut!
This kit can literally be built as fast as the modeler can apply CA glue and accelerator. Fantastic flight performance using either 2-stroke or 4-stroke engines. The aerobatic capabilities of this model are virtually unlimited due to its thick airfoil section and very light wing loading. A perfect club contest airplane.
Kit Features: Balsa and Ply Construction, Pre-Cut Sheet Balsa Tail Surfaces, Durable Aluminum Main Landing Gear, Formed Tailwheel Wire, Molded Clear Plastic Canopy, Full Size Plans, Fast-Building 2 Piece Wing For Easy Transportation, Full Size Plans, Engine Mounts, Sig Easy Hinges, Pushrods, Complete Hardware Pack & Large Decal Sheet.
Wingspan: 51.5 in 1308 mm Wing Area: 614 sq in 39.6 sq dm Flying Weight: 4.25-4.75 lb 1928-2150 g Length: 48.25in 1226 mm Radio Required: 4 Channel, 4 Servos Recommended Engines: .40-.46 cubic in (6.6 - 7.5 cubic cm) 2-Stroke, .56-.65 cubic in (9.2 - 10.7 cubic cm) 4-Stroke
Special notes about electric from Dave: This model makes an excellent electric conversion. My first large electric was one of these on 20 1750FAUP Cells. Yikes, I'd love to do another one with modern packs! Here is how I'd do it. Yes, this is same chart as the 4 Star 40, similar weight and wing area. An under recognized yet excellent electric conversion model. Good weight to wing area. A little troublesome to get large NiMH packs into due to the wing tube. However, with Lipo's it's super easy to fit the pack. Below are my suggestions for a range of practical power systems.
Setup and Performance Chart
Motor
# Cells
Prop
Amps
Watts In
RPM
Thrust oz.
Pitch Speed MPH
Climb FPM
Est. Top Speed
Himax 3522-0990
3
12x6
41.7
469
8,470
62
48
1377
53
Himax 3528-800
3
12x10
37.4
421
6,950
66
54
1260
56
Himax 3528-800
4
11x7
36.6
549
9,770
65
68
1674
61
Himax 3528-1000
3
12x6
44.5
501
8,690
49
64
1490
54
Himax 3528-1000
4
11x5.5
51.4
771
11,660
61
85
2177
64
Himax 3528-1000
3
12x6
44.5
501
8,690
49
64
1490
54
Himax 5018-530
5
12x8
30.5
572
8,560
65
76
1839
63
Himax 5018-530
6
12x8
40.5
911
9,930
75
104
2766
73
Estimates based on manufacturers provided constants using E-Calc. High Quality 2100-3000mah used as trial cell in calculations. Presumed model weight of 76oz. @3 cells (added oz for higher cell counts). Actual performance may vary depending on components, accuracy of data provided by manufacturer, quality of battery, ESC, and many other factors.
Fits Himax 35 series outrunners and many others. Motor plate is drilled for 4 bolt pattern of 1" (25.4mm)diameter. This is a most common mounting pattern in motors of this class such as Himax 35XX Series and many others (does not fit AXI 28XX motors). Standoffs provided in 4 different lengths to aid your setup. Measurements provided so you can figure out spacing. Note, if motor is mounted inside front plate, it's thickness does not add to motor spacing off firewall. High impact plastic base plate supports ends of standoffs against firewall to a solid and rugged mounting system.
Fits motors with 1" (25.4mm) mounting spacing Max motor length- 53mm Max motor diameter- 35mm for Outrunners, 36mm for regular motors 4 sets of rods included lengths; 12.65" (32mm), 1.655" (42mm), 1.892" (48mm) & 2.125" (54mm) Font plate thickness: .117" (3mm) Rear plate mounting space: .140" (3.5mm) Weight- 1.6 to 1.8 oz. Includes all necessary hardware
 "RRC K6 Series 4000 11.1V 3S 65C")
 "Castle Creations Phoenix 25")
 "Himax HC6330Pro 210kv F3A Brushless Motor, Light Weight 20-Pole Design")
 "RRC K6 Series 3300 7.4V 2S 65C")
 "Du-Bro 4 ounce Fuel Tank")
 "RRC K6 Series 5100 11.1V 3S 65C")
 "Himax HC3516 Outrunner 1350 KV")
 "RRC K6 Series 2600 14.8V 4S 65C")
 "MTO2836-1500")
 "Radical RC 700mAh AA NiCad 9.6V 8-Cell Airtronics Stylus/Futaba FG TX Pack")
 "Himax HC5018-530 Series Outrunner Motor")
 "RRC K6 1800 18.5V 5S 65C")
 "Slow Stick Canard Mounting Kit")
 "Himax 2025 4200KV Brushless Direct Drive")
 "FDK/Sanyo 1650 AA NiMH 7.2V 6-Cell Multiplex TX Pack")
 "Stand Off Motor Mount Small")
 "RRC K6 Series 7.4V 2S 1300mAh 65C")
 "GWS Mini LF Ball Bearing Servo Futaba")
 "MOLICEL Ultra-High Power 2800mAh Multi-Cell Pack, #INR18650-P28A Air")
 "Radical RC Quick Wing 20mm")
 "Hitec HS-485HB Heavy Duty Deluxe Ball Bearing Servo")
 "RRC K6 Series 3800 22.2V 6S 65C")
 "Sig Somethin' Extra Kit")
 "Stand Off Motor Mount for 35mm Outrunners")
