The DU-BRO Micro Push Rod System is a lightweight and easy-to-install control linkage designed for small to medium electric RC airplanes. It gives you smooth, accurate control while keeping the weight of your model as low as possible. This makes it perfect for foamies, indoor planes, park flyers, and small electric aerobatic models.

Each package includes two complete push rod systems, so you can set up two control surfaces--such as the elevator and rudder. Everything you need is included, and the parts are designed to work together for simple, clean installation.

Each set contains: 

• 2 pushrods with a pre-bent 90° end, ready to use
• 2 pushrod housings that guide the rods and stop them from bending
• 2 Micro E/Z Links for attaching to your control horn
• 2 Mini E/Z Connectors for attaching to your servo arm and making easy adjustments
   

These components allow for smooth movement with very little friction. They also make it easy to fine-tune your control surfaces so your airplane responds the way you want it to.

The Micro Push Rod System is available in four different weights to fit a wide range of aircraft sizes: 

• #847 - 3.2 grams per set
• #852 - 4.6 grams per set
• #922 - 5.7 grams per set
• #941 - 18 grams per set (for slightly larger electric planes) 

This system works great on: 

• Indoor flyers
• Small park flyers
• Slow flyers
• Foamies and EPP aircraft
• Lightweight scratch-built planes 

Installation is quick and beginner-friendly. The housings glue easily to your model, and the connectors make attaching and adjusting your pushrods simple.

Proudly Made in the USA, the DU-BRO Micro Push Rod System provides a dependable and lightweight way to get precise control from your electric RC aircraft. 

This item qualifies as a Rod Stock Item, read below:

Rod Stock Policy:

In order to include long skinny products at our very favorable shipping rates: All USA orders that contain rod-stock items need to contain at least 6 rods. Rod stock is anything over 30". This would include Music Wire, Carbon Rods of any kind, larger Pushrod kits, brass or aluminum rods and anything else of that nature. Thinner items like carbon strips .5mm thick, sub 1mm diameter carbon rods and music wire .020 or thinner ordered in quantities less than 6 rods total will be shipped coiled. Unless otherwise stated, all carbon rod stock is pull-truded construction grade. The resin is heat cured as the fibers are pulled through a die of the proper shape. Sizes are approximate usually within 5%. Weight is in grams per meter, as per the manufacturer documentation, no guarantees on weight.

Find other qualifying items to mix and match to meet the 6PC Minimum Purchase Requirement:

New Du-Bro Micro Pushrod System. (2) 20"x.032 pushrods, (2) 18" pushrod housings and (2) micro E/Z Links and (2 Mini E/Z Connectors. Great for indoor and park flyers! 90 degree bend is already on pushrods. 2/pkg.

TEMPORARILY OUT OF STOCK

To install, cut the housing and cable to length. Glue the housing into the model. Attach a Brass Coupler or Clevis to one end (by soldering, gluing or crimping). Insert the cable, and attach a Coupler or Clevis to the other end. Thread Clevis(es) onto the Coupler(s); you need a Coupler on at least one end for adjustability.

The .032 size cable is very flexible and light, and is excellent for throttle hookup for engine powered planes and for control surfaces in electrics and gliders.

36" Length, 1-1/2" Minimum Radius, 1 set per package

S507 - 2-56 Hardware

Splined carbon filled nylon. .032 diameter brass plated stainless steel cable - very flexible. Minimum bend radius 1.5". Clevis included. 1 unit per package.

Du-Bro Micro Aileron System designed for indoor and park flyer aircraft. Complete with Micro E/Z Link (2), Micro E/Z Connector (2), 1/32 (.032) push rods (2), .032 torque rods. Instruction sheet included.

Traditional aileron torque rod setup for your smaller park fliers and indoor models. Use one servo to drive two ailerons. Complete hardware included.