GWS Black, HD 3 Blade prop. Conventional tractor rotation. Includes an assortment spru of centering rings.
Priced per each propeller.

Tidy up and protect your servo wire. 3mm fits 1 servo cable. Works like Chinese finger cuffs, push ends toward center of piece to open up to insert wiring. Very nice for heli applications, keeps wires from straying and protects from friction damage. 3-foot packs available in Orange & Yellow. See other listings for color and size options.

Limited quantities, while supplies last... 

Synchronous Balance Charger / Discharger 

Charge Current Range: 0.1 ~ 25.0A
Discharge Current Range: 0.1 ~ 20.0A
Discharge Cut-off voltage: 3.0 ~ 4.0V
Maximum Charge Power Capacity: 350W
Discharge Power: 3-24V
Normal Discharger Power limited: max. 25W
Energy Transfer Discharge Power limited max.: 200W
Current Drain for Balancing Lipo Cells: 300mAh/cell
Lithium Battery Cell Count: 1 - 6 cells
Pb: 2-20V
NiCad & NiMH Cells: 1 - 18 cells
Charge & Discharge Lead Acid: 2 - 20V
Input Voltage DC: 11.0-24.0V

Includes charger, manual, wire set (see photo).

New in box, box is shelf worn, last one available, sold as-is, non-warranty, no returns, discontinued, last one left in stock.

Torque (4.8/6v)	Weight	Speed (4.8/6v)	Bearings	Size SAE	Size Metric	Type
15/18 oz/in - 1.1/1.3 kg.cm	8g/0.28 oz.	0.17 / 0.14s	Plastic	.9"x .5"x .9"	23 x 12 x 24mm	Analog

WHILE SUPPLIES LAST

SERVO CASE COLOR IS BLACK 

With solderable nickel tabs. Quality Kokum cell. 15C, 20C burst discharge capable cells. Lithium packs/cells require a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method. New.

Discontinued, non-warranty, while supplies last, all sales final. 

Weight is 3.2oz.This pack requires a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method. NEW.

Discontinued, non-warranty, while supplies last, all sales final. 

Tidy up and protect your servo wire. 10mm fits over servo cables. Works like Chinese finger cuffs, push ends toward center of piece to open up to insert wiring. Very nice for heli applications, keeps wires from straying and protects from friction damage. 3-foot packs available in Orange & Yellow. See other listings for color and size options.

Limited inventory, while supplies last... 

Hint! Need your joint to cure a little faster? Take a covering heat shrink gun to the joint and warm it up. Be carefull, the heat will at first cause the epoxy to become thinner, it might run out of the joint and make a mess. Also, be warned! A little heat goes a long way and can cause your glue to dry faster than you had planned. You can also preheat the glue before applying to the parts or pre heat the parts.

WHILE SUPPLIES LAST 

Learn about epoxy from an expert at RCModelReviews

Product Description

• Function Range Accuracy
• DC Voltage 200mV-1000V +- (0.5%+1dgt)
• AC Voltage 2V-750V +- (0.8%+3dgt)
• DC Current 2mA-20A +- (0.5%+1dgt)
• AC Current 2mA-20A +- (1.0%+3dgt)
• Resistance 200Ω -20MΩ +- (0.8%+1dgt)
• Capacitance 2nF-20u F +- (2.5%+3dgt)
• Frequency 2KHz-20KHz +- (1.5%+5dgt)
• Diode Test -Yes
• Transistor Test -Yes
• Continuity Buzzer -Yes
• Auto Power Off -Yes
• Data Hold -Yes
• Power Supply 9V Battery 6F22 (battery not included)
• Maximum Display 1999
• Product Net Weight 300g
• Products Size 191x 89x 35mm
• Standard Accessories Test Lead, Battery, Manual.
• Case Color is Orange/Yellow

• 3-1/2 digits LCD, Max. reading 1999
• 8 function, 32 Ranges
• Data hold
• Low battery indication
• Auto Power Off
• Overload protection 

Accessories:

Test lead; Users Manual;

Hint! Need your joint to cure a little faster? Take a covering heat shrink gun to the joint and warm it up. Be carefull, the heat will at first cause the epoxy to become thinner, it might run out of the joint and make a mess. Also, be warned! A little heat goes a long way and can cause your glue to dry faster than you had planned. You can also preheat the glue before applying to the parts or pre heat the parts.

WHILE SUPPLIES LAST 

Learn about epoxy from an expert at RCModelReviews

Incredible power to weight ratio. 4.2V 8000mah block weighs 183g/6.44oz. Battery can sustain up to 64 amps continuos. Up to 80 amps with ever increasing judicious use of throttle control. This pack requires a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method. NEW Comes raw, or choose finished w/connector choice below.

Discontinued, non-warranty, while supplies last, all sales final. 

Brushless motor, 20mm size with added diameter from cooling fins, uses neodymium magnets, carbon case and unique solder posts are manufactured using advanced technologies from finest materials - our standard. Twin ballraced hardened steel shaft and overall robust but very lightweight construction ensure very long lifetime. This small beauties are suitable for use with gearbox or in ducted fans. Tapped hols in front of case match S-400/480 motors making it compatible with many S-400/480 type gearbox's.

I use one of these on a delta and it's sick fast. Enjoy!

Specifications:
Voltage range 6-8 cells
RPM per Volt 6,370 RPM/V
Max. Efficiency with ESC 77%
Max. Efficiency Current 14-22 A (>70%)
Max. loading 28 A / 30 s
No load Current / 8V w gear 3,9 A
Internal resistance 49 mohm
Dimensions with gearbox 24,8x65 mm
Shaft Diameter Gearbox 4 mm
Weight with gearbox 77 g
Recomended model weight 600 - 1200 g
Propeller range VMGM 6,00:1 6 cells prop 12"x8"
VMGM 6,00:1 7 cells prop 11"x7"
VMGM 6,00:1 8 cells prop 10"x6"

Non-warranty; Closeout; No Returns Accepted. 

WHILE SUPPLIES LAST, NON-WARRANTY, FINAL SALE 

 Short kit only for Tomboy Kit BB224

SHELF WORN PACKAGING, SOLD AS IS; NON-WARRANTY; NO RETURNS. 

This device was designed to pair up with our Nano Electronic Receiver Switch. The mechanical relay gives you completely isolated switching of any circuit, and you can even use 120VAC power. Just apply power (5V) to the coil pins to make the relay switch. You could use this relay to control pretty much anything with your radio; a motor, a glow plug, a toaster (or maybe xmas lights?). This would also be perfect as a kill switch for an engine ignition and you won't have to worry about the ignition circuit causing interference because the circuits will be completely isolated.

DISCONTINUED, WHILE SUPPLIES LAST... 

Incredible power to weight ratio. 7.4V 2000mah pack.  This pack requires a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method. Discontinued, non-warranty, limited quantity, while supplies last, all sales final. NEW. REG. $47.00

SALE !!!

Torque (4.8/6v)	Weight	Speed (4.8/6v)	Bearings	Size SAE	Size Metric	Type
76/94 oz. 5.5/6.8 kg.cm	55.2 g /1.94 oz.	0.18/0.15s	2BB	1.6"x 0.8"x 1.5"	41 x 20 x 38mm	Analog

Choose Quantity Option below. Want 1, 2, or 3 servos? Select first option, then enter quantity 1, 2, or 3. Want a bulk discount? Select bulk quantity, then enter quantity of 1.

DISCONTINUED BY HITEC, WHILE SUPPLIES LAST! 

Applications: Heli's and Aircraft up to 72" or up to 12lbs when using just one servo per control surface.

Torque (4.8/6v)	Weight	Speed (4.8/6v)	Bearings	Size SAE	Size Metric	Type
69/83 oz. 5.5/6 kg.cm	50 g/1.76 oz.	0.18/0.15 s	2BB	1.6"x 0.8"x 1.5"	41 x 20 x 39 mm	Analog

DISCONTINUED BY HITEC, WHILE SUPPLIES LAST! 

Product Introduction

Linear High Precision Regulator system (No switching Noise generated)Digital Controlled Electrical (MOSFET) Power Switching System.

3steps Low voltage sound and visual warning indicators.

The DYMOND DIGI SWITCH is an electronic switch with a powerful integrated BEC for use with two-cell LiPo battery packs.

The DIGI SWITCH provides a low voltage control for the connected LiPo pack, that outputs a visual and audible signal as the battery pack gets empty.

Linear BEC without any switching noise

3-stage low voltage warning

Extremely low power consumption in the off state (only 0.047 mAh)

Specifications

Nominal input voltage: 7.4V, 2-cell LiPo, max. > 1

Output voltage: 6V

Rated current: 5.5A continuous current at then 5V output voltage

Self power consumption

Off: 0.047 mAh

Off: 0.047 mAh

On mode: 3.9 mAh

With signal: 21 mAh

Dimensions: 59 x 20 x 21 mm

Dimensions for mounting hole: 17 x 46 mm, 19 mm mounting depth

Weight: 19.8g

Low voltage warning

Below 7.0V: Slow sound and flash frequency

Below 6.6V: Medium Speed sound and flash frequency

Below 6.0V: Rapid Tone and flash frequency

1. When the switch is on/off, press and hold the button for about 1 second.

2. Regulator built-in digital electronic switch.

3. When the voltage drops, it will be notified by LED lights and sound.

The standard of excellence in receiver technology.
Berg brand crystals are manufactured to the highest tolerances in order to maximize the superior selectivity, sensitivity, and noise rejection qualities of our Berg receivers. We don't recommend using any other brand of crystal for these reasons.
Choose from channels 11 through 60 below.

Choose your Channel preference below, USED or NEW preference option, and any alternate channels you will accept if we don't have your first choice, below in the box.

Note: Our USED inventory is always changing due to our Crystal Exchange service: https://www.radicalrc.com/shop/Radical-RC-Crystal-Exchange.php

Listed frequencies/channels are not guaranteed in stock, we'll check and always do our best to fulfill your request. 

WHILE SUPPLIES LAST! 

The LiPoChecker Pro8s is a voltage checker and a balancer / equalizer for LiFP+Lion+LiPo Lithium batteries combined in one device. Eight separate circuits allow the LiPoChecker pro to balance battery packs up to 8s and a maximum charging voltage of 4.23 V per cell. This can be done preferably during charging, but also afterward or during a full test of the battery pack. The LiPoChecker pro universal connector system (16pin header), known from Personal Computers, is easily available and allows an easy adaptation to common connector systems, such as Graupner, robbe, Thunderpower, Tanic, Polyquest etc. Ready-to-use adapters are available from Orbit electronic. An additional SIO feedback line allows voltage data of the individual cells to be sent to the evoJet Orbit POCKETLADER or MICROLADER battery chargers. That way, alarm states can be easily detected (closed loop) and the charging result can be optimized even with old or low-grade battery packs.

Connection: 16 pin male header
Operating voltage: +2.1V to +4.5V
Diversion: max.1000mA
Balancing: 3.4V - 4.23V
Dimensions: 41 x 16 x 160 mm / 1.6" x 0.6" x 6.3"

SOLD OUT 

The Phantom X4 Charger is a four-channel battery charger designed and built exclusively for DJI PhantomTM 3 and DJI PhantomTM 4 Smart Batteries. This charger is capable of charging, storing and deep cycling four DJITM smart batteries simultaneously. Two smart devices can be charged via USB ports and two remote controllers can be charged at the same time.
Chargers DJI Phantom(TM) 3/4 Smart Batteries
Quickly Charges Four Batteries Simultaneously
Charges 2 Remote Controllers
Charges 2 Tablet Devices (While batteries are charging)

This is the Hitec Phantom X4 Smart Battery Charger for the DJI PhantomTM 3 and DJI PhantomTM 4 Smart Batteries.

FEATURES
Designed exclusively to charge DJI Phantom 3/4 Smart batteries, Phantom 4 Smart batteries require adapter (not included, part #61116).
Charges, stores and deep cycles four DJI batteries simultaneously
Two smart devices can be charged via USB ports, and two remote controllers can be charged at the same time
One year limited warranty through Hitec beginning at date of purchase

INCLUDES
Hitec Phantom X4 Smart Battery Charger
AC Power Cord
Micro B Type USB Charge Cable
Two Remote Controller Charging Cables
Instruction Manual

REQUIREMENTS
#61116 Adapter cable if wanting to charge Phntom 4 batteries

SPECIFICATIONS
Input Voltage: AC 100-240V
Charge Power: 100Wx4
Charge Current: 6.0A
USB Output: 5V/2.1A x 2
DC Output: 19V/2A x 2
Dimensions: 10 x 5.6 x 7.1" (255 x 142 x 180mm)
Weight: 7.1lbs (3.22kg)

Manufacturer Mailing Address
Hitec
HITEC RCD USA, INC.
12115 PAINE STREET
POWAY, CA 92064
Additional Manufacturer Contact Info
Web Site: https://www.hitecrcd.com/
Email: service@hitecrcd.com
Phone: 858-748-6948

DISCONTINUED BY HITEC, WHILE SUPPLIES LAST!