GF Nylon Spinners have light weight aluminum back plate. No special prop nut or adapter is required. Spinner is held to back plate with two attachment screws. Machined groove supports edge of spinner. Back plate is knurled on both sides to grip both your prop and prop adapter making it easier to tighten than other spinners of this style. Size 1.5" (38mm) OD. Factory shaft hole in back plate is .197" (5mm). Overall Length is 1.4" (35.5mm).
See this and all other new sizes up to 75mm in Spinners-Fixed-Props. Within "E-Power-Everything".
High resolution display with 10 high intensity LEDs. 12 bits microchip IC design, for accurate voltage readings. Large LCD display shows battery voltage and 7-step capacity graphic display. Capable of measuring 1-2-3-4 cell (3.7V-7.4V-11.1V-14.8V) Li-Po or 4.8V-6.0V-9.6V NiXX battery packs. The test sequence shows battery condition under 500mA load. Test range is between 3.7V-20V. Reverse polarity protected. Universal test probe included.
This is the pencil iron we use to build hand solder packs in our shop. Capable of soldering large cells and large wire. If your tired of all the toys, here is an iron with spirit that will get the job done. Safety light lets you know when it's on, tip temperature up to 900 degrees F, 5 foot power cord, stainless body and simple iron support.
And you thought the story about aliens at Wright Patt was just a conspiracy theory? At long last, a durable light weight quad copter airframe kit. This kit makes use of basic 10mm square carbon, fiberglass or aluminum tubes. All of our 10mm boom based Slow Stick hopups such as servo mounts, battery tray's, gear mounts and etc.... are compatible with our Quad Coper Designers Kit.
By making use of different motor systems and different boom lengths, you can make a quad of any size you like up to 1 meter (39") frame OD...............
We are very excited about this new soldering workbench. The manufacturer allowed us to get some modifications and enhancements into this design. Features metalic surfaces and magnetic jigs. Tools can be mounted on the back wall or horizontal surface of the jig as shown. Magnets allow for easy repositioning to match any need. Comes complete with Pack Holder, Conector Holder and Wire Vise. Connector holder fits Deans, XT-60 and 3mm bullets. Extra wire clamps and blank tool holders are available separately. This is a kit with simple photo instructions. Easy to build. This is one our our feature new items for Toledo 2011.
Handy soldering fixture. Use to hold wires steady while soldering. Plug clamp (hiding in rear of photo) holds Deans, XT-60 and other housing type plugs. Machined from billet aluminum. Made here, not imported.
Over Stock Sale! We've got about 30 bottles to blow out. Regular $3.00 On sale now 33% off, just $1.99. Great way to get some top quality Mercury Thick CA on hand for when you need it!
Mercury M1100G Instant is a thick gap filling viscosity that bonds to a wide variety of materials including wood, paper, cardboard, ...................
Check the listing in adhesives if you want to read more about it. Order in this listing only to get the sale price.
Mercury M1100G Gap Filling Viscosity adhesive 2oz ON SALE!
Over Stock Sale! We've got about 20 bottles to blow out. Regular $9.00 On sale now 33% off, just $5.99. Great way to get some top quality Mercury Thick CA on hand for when you need it!
Mercury M1100G Instant is a thick gap filling viscosity that bonds to a wide variety of materials including wood, paper, cardboard, ...................
Check the listing in Adhesives if you want to read more about it. Order in this listing only to get the sale price.
Great tail wheel assembly for 120 through 50cc models. Parts are prebent, fasteners, spacers, wheel collar and clevis inlcuded. Wheel is about 2 1/8" (54mm).
RRC V-Reg Digital Switch JR/Hitec/Spektrum Type Plugs
A digital switch and linear voltage regulator in one that simplifies wiring in your craft. Rated for 10 amps constant, 20 amps burst (Max 8 seconds). Perfect for use with 2S LIPO packs. Simple opperation, hold button 1 second to turn on, hold button 1 second to turn off.
Low voltage warning beeps start when input voltage falls to 7V, increased warnings at 6.6v. Warning beeps and flash become rapid at 6V. So efficient, when off, it would take 886 days to consume 1000mah out of your pack.
Specifications:...............
To see full specifications and all other Switches: Switches-Radio-Misc within Radio Plugs & Wiring.
To see full specifications and all Voltage Regulators within Onboard Electronics.
Weldbond is a non-toxic, fume free adhesive formulated for smooth and porous surfaces alike. Bonds almost anything to anything. Weldbond is not flammable, non toxic, non staining and won't become brittle with age. It may be mixed with water to form a brushable sealer if so desired. Weldbond is Foam Safe and works well with Depron, Poly-Styrene and other hobby foams. Joint remains slightly flexible which is desireable with Depron and other sheet foams.
If your friends all think your models are bricks, this is the glue for you as it's also advertised as a great masonry adhesive. Many purposes, one adhesive.
14 New Items! Some interesting in-between sizes for Glow or Electric flight are available again. 3 Bladed props from 3.125" up to 5", 2 blade from 3" to 6". Neat pusher sizes also available. Great for Glow or E-Power flight.
Prop Adaptor for 3.0mm(0.12") motor or gearbox shafts. Lite weight version.
Radical RC, The go to place when you need a prop adapter. 48 different adapters from 1.5mm thru 10mm in stock. Ready......Contact..... Brovrooombrarooombrarooombraroooom.....
A great product to use where corrosion protection is desired without inhibiting conductivity. Excellent for high temp and high current applicaitons. A very light smear will make Deans and other tight connectors easier to work.
The SSX Biplane Build Kit includes detailed graphic instructions, high quality laser-cut wood to build
the bi-wings and tail sections, along with a 10mm carbon fiber fuselage, carbon fiber struts, Millennium
R/C's own X-Gear landing gear, outrunner motor mount and X-Fuse battery mount, servo mounts,
adjustable pushrod guides, steerable tail gear and wheels. Special features of this kit include plug-in
wings with carbon wing tubes to make transporting the model a breeze! Recommend using any light
covering, such as SoLite, Ultracote Lite or ParkLite. (Power components not included in airframe kit).
At last! An all chemistry charger charger that runs on both 12V and 110VAC input power. Complete with illistrated instuctions. Even includes a charging flow chart in the booklet. Charges Nicad, NiMH, Lipo, A123 (LIFE) and PB (Lead Acid cells). Balances lithium type packs automatically in balance mode..............
Use to offset a second boom from your main boom. Imgaine a Schiender cup racer but rather than a float centered under the fuse, we're adding a second boom. Original intention is to locate a second boom below your main boom to hold landing gear, battery and camera mount for FPV experimenters. In this way (with other parts available separately) Can be used to configure Slow Stick for single tractor motor with camera position in front of prop if you like.
Other uses are possible, perhaps you want to put a boom up above your wing to hold motor or camera above prop. Use your imagination with this special kit.
On model in photo parts are colored black with permanate marker. Made from laser cut 3/32 Aircraft Plywood. This kit offsets second boom with 4 3/8" gap.
Kavan Bar Clamps. With parallel jaws, useful for fuselage assembly or any other situation where you need a temporary "helping hand". Uses rubber bands for clamping force so you can adjust tightness to match materials and situation. Pack of 5 clamps. Smaller clamp as shown in photo.
NASA wants to go back to the moon. Radical RC's Wicked Wing beat them to it! Check out our original designs! Radical RC Verti-Go 125, Verti-Go 3D, E-Hornet, Mini Stick, Micro Stick, Micro Bipe, Micro Low Stick, Quick Wing 12mm, Quick Wing 20mm, Quick Wing Twin 20mm Double Trouble, Das Mini Low Stick, Das Mini Bipe, Mini Hunter, Mini Intern Trainer, Stick 600,
We cover all the basics on charging and cycling, and the receivers that we provide. PLEASE READ THIS PRIOR to sending any items back. 99% of all returned items test perfect. Learn how to check your cycler/charger or receiver here without spending money on postage.
Pictured to left is one of Garrett's competition ships, to right .... Dave, Here is a picture of my second plane. This is a 3W Extra 330 40%. The plane is flying great. Thanks so much for all your support in this hobby. I really like using your products. My friends as well are very happy with the equipment & fast-friendly service that is coming out of your company. Let's keep in touch. -Garrett Morrison
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
