|
| |
Futaba J end with two heavy duty 22 gauge for battery use. Understand, Male and Female gender type refers to the plastic connector body and not the pins. All 2 wire pigtails are about 10" long. $2.00 per lead/pigtail.
LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00. Mix and match any way you choose (Female connector shown in listing below).
SKU Number: RRC2PPMFJ
|
|
|
|
|
| |
Female Futaba J Radio Connector Pins only, 10-Pack = 30 pins, for use with our special Hobby Pin Crimp Tool to make your own custom extensions, Y's etc. All pins are gold plated.
These Female Pins are for installation into Male Futaba J Shells.
SKU Number: RRCPINFFJ10
|
|
|
|
|
| |
Male Futaba J Radio Connector Pins only, 10-Pack = 30 pins, for use with our special Hobby Pin Crimp Tool to make your own custom extensions, Y's etc. All pins are gold plated. These Male Pins are for installation into the Female Futaba J Housings/Shells.
SKU Number: RRCPINMFJ10
|
|
|
|
|
| |
Use these Female pin kits with our special Hobby Pin Crimp Tool to make your own custom extensions, Y's etc. Build it to fit your setup exactly. The two arms of Y harnesses and RX's are Female. What you plug a battery into is female. Since the connector pins are covered by the connector jacket the unit is gendered as female. This kit contains enough parts to build 10 Female (fewer parts show in photo). All pins are gold plated. Available in multiples of 10 below.
SKU Number: RRCKIT10FFJ
|
|
|
|
|
| |
Female 2 wire battery Switch lead. This is the lead the battery plugs into like on your switch. 22 gauge This is not to be put on a battery. All 2 wire pigtails are about 10" long. $2.00 per lead/pigtail. Select wire option: 22 gauge heavy duty or 26 gauge standard duty.
LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00. Mix and match any way you choose (Male connector shown in listing above).
SKU Number: RRC2PPFFJ
|
|
|
|
|
| |
Just like a servo end. Understand, Male and Female refers the plastic connector body and not the pins. All 3 wire pigtails are about 10" long. Select below: 22 gauge heavy duty or 26 gauge standard duty.
LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00. Mix and match any way you choose (Female connector shown in listing below).
SKU Number: RRC3PPMFJ
|
|
|
|
|
| |
Like RX end. Use to build your own Extensions, Y's etc. Understand, Male and Female refers the plastic connector body and not the pins. A servo plugs into the Female plug. All 3 wire pigtails are about 10" long. Select below: 22 gauge heavy duty or 26 gauge standard duty.
LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00. Mix and match any way you choose (Male connector shown in listing above).
SKU Number: RRC3PPFFJ
|
|
|
|
|
| |
6 inche extension includes ferrite toroid. Perfect between RX and throttle servo which is mounted up front near spark ignition system. Greatly reduces RF interference from ignition system that would otherwise wick down servo wire into your RX. Also useful for battery packs or any other items located close to ignition or any other source of unwanted RF.
SKU Number: RRCRFNSUP6FJ
|
|
|
|
|
| |
3",6", ~10" or ~12" Futaba Style servo extension harness, 22 gauge heavy duty wire.
Select length desired below.
SKU Number: RRCEXT03/06/10/12FJ
|
|
|
|
|
| |
Futaba Extension Harness 18", 24", 30", 36" or 40". Futaba Style servo extension. 22 gauge heavy duty wire.
Select length desired below.
Please refer to photo of above extensions to see similar leads.
SKU Number: RRCEXT18/24/30/36/40FJ
|
|
|
|
|
| |
Micro Lite Extension harness, 29" long. Very light weight for use on foamies, park flyers, sailplanes, 1/2A and other lite applications. 30 gauge fine, lightweight wire. Universal connectors. TEMPORARILY OUT OF STOCK
SKU Number: RRCEXT29ML
|
|
|
|
|
| |
RadicalRC Futaba J Style Extension Harness 78 inch (200cm) Buffered/Filtered. Futaba Style servo extension. 22 gauge heavy duty wire.
SKU Number: RRCEXT78BFJ
|
|
|
|
|
| |
RadicalRC JR Style Extension Harness 78 inch (200cm) Buffered/Filtered. JR Style servo extension. 22 gauge heavy duty wire.
SKU Number: RRCEXT78BFJR
|
|
|
|
|
| |
Great part to use when there would be a little too much wire left over otherwise. 22 gauge wire so this is heavy duty. Gold contacts.
SKU Number: RRCYSHORTFJ
|
|
|
|
|
| |
Y harness. 10" long. Use to run two servos off one channel output on RX. Futaba connector style, 26 gauge heavy duty 60 strand wire, gold connector pins as always.
SKU Number: RRCYSTDFJ
|
|
|
|
|
| |
Micro Lite servo pigtail. Super light weight for Foamies. Your servo end fits into this female connector end. JR and Hitec are same. Tech Note: Male and Female refers the plastic connector body and not the pins. Micro Lite pigtails are about 5" in length.
LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two wire battery male single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00. (Male universal connector shown in listing above).
SKU Number: RRC3PPMLFFJ
|
|
|
|
|
| |
Y harness. 10 to 12" long. Use to run two servos off one channel output on RX. Futaba connector style, 22 gauge heavy duty 60 strand wire, gold connector pins as always.
SKU Number: RRCY12HDFJ
|
|
|
|
|
| |
Block End Y Harness. 6" long. Use to run two servos off one Rx channel. JR-universal male to universal block end female connector. A JR or Futaba J servo will plug into the block.
SKU Number: RRCY06BLOCKFJ
|
|
|
|
|
| |
Simple installation. Adjustable trimpot. Works with AM, FM, and PCM. Operates with 4.8v to 6.0v. This is "Y" configuration. Gold plated connectors.
SKU Number: CER216FJYGSR
|
|
|
|
|
| |
Long leg Y harness. Need to drive 2 servos in a tail that are close to each other but far from the receiver? Here is a special part to solve some of those special problems. The Arms are fixed at 3" for all sizes. The Leg is available in variable length. Select leg length below. 22 gauge heavy duty wire. Note: JR harnesses on left and Futaba J on right.
SKU Number: RRCYSTLL03AFJ
|
|
|
|
|
| |
This nifty Y harness invented and available exclusively at Radical RC is handy to use for loaded voltage and current testing of your radio system. Here is what it can help you do: 1. Use in conjunction with an amp meter to test current to any one servo or between the battery pack and the entire system. 2. Use a combo of your amp meter and ESV to see how far your battery voltage is depressing at a given load. 3. Use in combination with our ESV to see what your voltage is while your system switch is on. A jumper plug is used to complete the connection when your doing volt only and no amp tests. Regular hobby battery test and charge cords (you probably already own) can be used to interact with this Y harness. Here is how is how to use me:
To measure current. First set your meter to measure amps and set it one setting higher than you expect to measure so as not to damage your meter. For a typical aircraft you might start at 5 or 10 amps range to be safe. You can reduce the range later (if that is an option) once you know your not going to over drive it. For many digital meters you'll have only two settings, one low like 300mah or less and one for over 300mah up to 10 amps. Use the higher of these two settings for most applications. Unplug the jumper plug. The jumper plug is shown unplugged above at the top of the photo. Plug your JR or Futaba RX charge cord in where the jumper was (notice all black wires here) plug the banana ends of your charge cord into your meter (most meters use standard 4mm banana inputs) correctly. Your meter completes the ground wire connection between your battery and your RX or Servo (or whatever load your checking). Run your device and take your reading. To measure voltage, Set meter for DC, if it has a set of ranges, choose a lower range like up to 10V (this setting should be above what you expect to measure). Plug the jumper back in and plug your charge cord into the other arm of the Y. Plug the banana plugs from your charge cord into your meters volt check inputs. Take reading. If you have 2 meters, you can test voltage and amps load at the same instant. Also, with 2 Test Y Harnesses, you can take readings between the battery and also at a distant servo. Maybe you want to know how much voltage drop there is at the end of the line in your tail servos for example. In this case you need to know the loaded voltage at the battery and also at the distant servo to see what the actual drop in your wiring harness's really is. If you only measure at the servo your total voltage drop will be the total of the wiring and the battery and not just the wiring. Not reccomended for any in-flight applications.
SKU Number: RRCYTEST
|
|
|
|
|
| |
Long Arm Y harness. Great to drive 2 aileron or flap servos from the same channel in a large wing. Eliminates risk and weight of all those extra hidden connectors you'd have if you piece together a bunch of stock sizes. Here is a special part to solve some of those special problems. The Leg is 6" for all sizes. Arms (to plug servos into) are variable length. Length below is for each arm so 24" Long Arm Y has 48" spread. Size choice is length of each arm from y joint. Pick your size below. 22 gauge heavy duty wire. Note: JR harnesses on left and Futaba J on right.
SKU Number: RRCY06L__AFJ
|
|
|
|
|
| |
Use these Male pin kits with our special Hobby Pin Crimp Tool to make your own custom extensions, servo leads, Y's etc. Build it to fit your setup exactly. Battery ends and servo ends are male. This kit contains enough parts to build 10 male ends (fewer parts show in photo). All pins are gold plated. Available in multiples of 10 below.
SKU Number: RRCKIT10MFJ
|
|
|
|
|
| |
Bulk pack of Futaba J compatible pins and shells. This kit contains enough parts to build 25 male battery or servo ends. All pins are gold plated.
SKU Number: RRCKIT25MFJ
|
|
|
|
|
| |
Bulk pack of Futaba J compatible pins and shells. This kit contains enough parts to build 25 female ends. All pins are gold plated.
SKU Number: RRCKIT25FFJ
|
|
|
|
|
| |
Bulk pack of Futaba compatible pins and shells. This kit contains enough parts to build 50 male battery or servo ends. All pins are gold plated. Photo is sample for identification of parts only and not representative of quantity.
SKU Number: RRCKIT50MFJ
|
|
|
|
|
| |
Bulk pack of Futaba compatible pins and shells. This kit contains enough parts to build 50 female ends. All pins are gold plated. Photo is sample for identification of parts only and not representative of quantity.
SKU Number: RRCKIT50FFJ
|
|
|
|
|
| |
3-Pole/Wire 4" Micro Lite V Harness. Very light weight for use on foamies and park flyers. Use to run two servos off one channel output on RX. JR/universal male to two Futaba J females connector style.
SKU Number: RRCV04ML
|
|
|
|
|
| |
Micro Lite Servo V harness. 6" long. Very light weight for use on foamies and park flyers. Use to run two servos off one channel output on RX. Connectors are Futaba females and JR-universal male.
SKU Number: RRCV06ML
|
|
|
|
|
| |
Micro Lite 3-Pole/Wire Extension harness. 3" long. Very light weight for use on foamies and park flyers! 30 gauge fine, lightweight wire. Universal connectors. TEMPORARILY OUT OF STOCK
SKU Number: RRCEXT03ML
|
|
|
|
|
| |
Micro Lite 3-Pole/Wire Extension harness. 6" long. Very light weight for use on foamies and park flyers! 30 gauge fine, lightweight wire. Universal connectors.
SKU Number: RRCEXT06ML
|
|
|
|
|
| |
Micro Lite Extension harness, 10" long. Very light weight for use on foamies and park flyers! 30 gauge fine, lightweight wire. Universal connectors.
SKU Number: RRCEXT10ML
|
|
|
|
|
| |
12" Female Connector Single-Sided J-Series Connector (Female) (FPC-8J) Additional information: Weight: 1.5 oz Dimensions: 7 x 4 x 1 in
SKU Number: FUTFPC8J
|
|
|
|
|
| |
Futaba AEC-2 Dual Servo Extension
SKU Number: FUTAEC-2
|
|
|
|
|
| |
Futaba AEC-1 J-Aileron Extension Cord
SKU Number: FUTAEC-1
|
|
|
|
|
| |
Universal Y w/ Digital reverser (fits Futaba/Hitec/JR/Airt. Z) for 4.8v - 6.0v applications. This Reversing Y-Adapter is designed for giant scale, glider, pattern, or sport planes with split-elevators, split-flaps, or twin-engines. This Y-Adapter will reverse one servo and keep the other servo straight. COMING SOON
SKU Number: MPI3469D
|
|
|
|
 "2-Pole/Wire Battery Pigtail Single End Male Futaba J")
 "Female Futaba J Radio Connector Pins only, 10-Pack = 30 pins")
 "Male Futaba J Radio Connector Pins only, 10-Pack = 30 pins")
 "Female Connector Pins, Shells, & Housings Kit Futaba J")
 "2-Pole/Wire Battery Pigtail Single End Female Futaba J")
 "3-Pole/Wire Servo Pigtail/Conn. Single End Male Futaba J")
 "3-Pole/Wire Servo Pigtail/Conn. Female Futaba J")
 "RF Noise Suppression Extension Futaba J")
 "Futaba HD Extension Harness 3\", 6\", ~10\", or ~12\"")
 "3-Pole/Wire Micro Lite Extension Harness 29\", Universal")
 "RRC Extension Harness 78\" (200cm) Buffered/Filtered Futaba J")
 "RRC Extension Harness 78\" (200cm) Buffered/Filtered JR")
 "Short Heavy Duty Y Harness Futaba")
 "Servo Y Harness Futaba Standard 26ga")
 "3-Pole/Wire Micro Lite Servo Pigtail, Futaba Female")
 "Servo Y Harness Futaba")
 "Block End Y Harness Futaba")
 "Cermark Servo Reverser Futaba J-Y-Gold")
 "Super Tail Y Harness Long-Leg Futaba J")
 "Testing Y Harness")
 "Super Y Harness, Long Arm Futaba J")
 "Male Radio Connector Pins & Shells Kit Futaba J")
 "Male Connector Pin Kit Futaba J 50 Bulk")
 "3-Pole/Wire Servo 4\" Micro Lite V Harness")
 "3-Pole/Wire Servo 6\" Micro Lite V Harness Universal")
 "3-Pole/Wire Micro Lite Extension Harness 3\"")
 "3-Pole/Wire Micro Lite Extension Harness 6\"")
 "3-Pole/Wire Micro Lite Extension Harness 10\", Universal")
 "Futaba 12\" Female Connector Single-Sided")
 "Futaba AEC-2 Dual Servo Extension")
 "Futaba AEC-1 J-Aileron Extension Cord")
