Use our Caribbean Blue filament, just to get into the spirit of the islands or for any great blue project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Forest Green filament, just to get into the spirit of the pines or for any great green project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Grass Green Standard filament, just to get into the spirit of summer grass or for any green project!  It is a great shade that makes you almost want to lay down on it and look up at the clouds! 

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Bubblegum Pink filament, just to get into the spirit of PINK or for any great pink project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Metallic Gold filament, just to get into the spirit of this beautiful Gold or for any great metallic gold project! Metallic Gold is the most metallic you can get without any metal or abrasives. 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Tangerine Orange filament, just to get into the fall/Autumn/Halloween/Pumpkin/Tangerine spirit or for any great orange project! If bright orange is your color, you'll love our Tangerine Orange Filament! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Autumn Orange filament, just to get into the fall/Autumn/Halloween/Pumpkin spirit or for any great darker orange project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Island Fuchsia Standard filament, just to get into the spirit of island flowers or for any fuschia (not quite magenta, not quite purple) project! Island Fuchsia Standard PLA3D 3D printer filament is right in between. Sometimes called Barney Purple, our Island Fuchsia filament will make your prints pop! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Grape Purple filament, just to get into the spirit of the grapes or for any great purple project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Metallic Copper filament, just to get into the Fall or Autumn spirit or for any great metallic brown project! Metallic Copper is the most metallic you can get without any metal or abrasives. 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Daffodil Yellow filament, just to get into the spirit of Daffodils or for any great yellow project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Fire Engine Red filament, just to get into the spirit of Fire Engines or for any great red project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Cobalt Blue filament, just to get into the spirit of the blues or for any great coblat blue project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use Re-Fuel Recycled filament, just to get into the spirit of the creativity for any great project! It works great, prints great, and is otherwise almost equal to our normal PLA lineup. In fact, being run through a 2nd time, it often has better tolerances than the first run material. ReFuel comes vacuum-sealed with desiccant in a plain brown box with minimal labeling. 4kg spool available by request. E-mail for price and availability. No Color selection on this item.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Warm Bisque Standard filament, just to ease your spirit or for any pastel project!  

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Chocolate Brown filament, just to get into the spirit of Chocolate or for any great brown project!

Standard PLA is a basic, entry-level PLA filament. It's available in a broad color selection and uses only virgin NatureWorks Ingeo 4043d PLA resin. No fillers or stretchers means a more predictable 3D printing experience.

Because 3D Fuel doesn't use fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Standard PLA, or, Polylactic Acid, is among the most popular 3D printing materials in the world because it is easy to print and strong. Standard PLA is a hard plastic that produces a barely noticeable, but quite pleasant, sugary smell when extruding.

4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Buzzed is a beer based 3D printing filament made using waste byproducts from the beer making process. 3D Fuel uses those beer left-overs to create a special 3D printing material. Printing with Buzzed beer filament results in visibly unique print finishes. The filament produces products with a rich golden color and a noticeable natural grain. Buzzed beer filament can be printed on any machine capable of printing PLA. Standard PLA settings can be used. Note: Because this material uses bio-waste, color may vary from batch to batch.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 1.1 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Simply Silver filament, just to get into the spirit of all things silver or for any silver project! 4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel

Use our Snow White filament, just to get into the spirit of snow or for any great white project! Architectural and engineering models look fantastic in Snow White, one of our most popular colors of Standard PLA 3D printer filament. If you can't decide which color of Standard PLA to go with, you can never go wrong with Snow White; it is an excellent pick.

4kg spool available upon request.

Print Settings Hotend Temp: 190-220C
Bed Temp: 0-60C
Bed Surface: PEI, heated bare glass, blue painters tape, BuildTak, WhamBam
Recommended Print Speed: 40 – 100 mm/s

Since there are no fillers, the ideal print temp might be 5-10C higher than your current PLA settings.

Weight: 2.2 lbs
Dimensions: 8.3 × 3 × 8.5 in
Manufacturer:  3D Fuel