LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00. Mix and match any way you choose (Female connector shown in listing below).

LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00.

TEMPORARILY OUT OF STOCK 

LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" Deals you want because your getting 5 connectors for the price of 4 at $8.00. Mix and match any way you choose (Female connector shown in listing below).
SKU Number: RRC3PPMATX

This compact controller can keep it's cool even during the most extreme 3D maneuvers. Talon 25 is intended for use in most 400-size helicopter setups running up to 6S LiPo or your favorite 3D foamy that pulls up to 25 amps. Despite it's size, it boasts an impressive 8 amp peak/3 amp continuous BEC, keeping even the most draining servos at ease. Talon 25 also offers Castle's industry-leading helicopter functions, not to mention easy programming using the Castle Link USB adapter (coupon for free Castle Link included). Talon 25 tips the scales at a mere 18 grams!

Notes from Dave: This is a world beater ESC. Now we can run high voltages in our smaller models with a small tight ESC from a quality manufacturer. I'm very excited to put one of these in my 5S, 16 ounce Stick 400. Sweet!

Input Voltage: 2-6 Lipo
Max Continuous Amperage: 25*
BEC Voltage: 5.5v
BEC Amperage: 3 Continuous, 8 Surge**
Switching Rate 7,000 Hz
Resistance 0.0065 Ohms
Brake yes, programmable
Reversible yes - change any two wires
Size .072 x 1.72 x 0.32 in.
Weight (w/wires) 0.63 oz. (17.9g)
Universal connector

*RC HOBBY APPLICATION RATING: 25 amps for the duration of a single 4,000 mAh battery pack with the ESC in contact with a 5 mph airflow of 25C (77F) or cooler air. Controller temperature must never exceed 100C (212F). Exceeding current or temperature ratings may damage components and may shorten the life of the ESC. Always verify system current draw at full-throttle. Decrease load or increase airflow to decrease the ESC's operating temperature.

**Peak indicates amperage sustainable for most servos' current draw transients. Always confirm servo current draw before the first flight of the model.

Castle Creations Warranty Info.

SOLD OUT, ETA 2026

Included: 25 Feet Futaba Color Coded Servo Heavy Duty Twisted 22ga Wire
10 each Male End Connectors
10 each Female End Connectors
Radcial RC Connector Crimp Tool
SKU Number: RRCMCCSF

Easily snaps over simple L bends to retain your pushrod end in servo or control surface horn. For .072 wire size. .072 is the diameter of the non-treaded portions of 2-56 pre-threaded pushrods.

By making use of different motor systems and different boom lengths, you can make a quad of any size you like up to 1 meter (39") frame OD. Our motor mounts are light enough for small outrunners and strong enough for even 28mm size outrunners. You can use this kit as the basis for your special project. Want to carry your GoPro camera to get that special shot? Want to build a Quad FPV? Want to deliver a can of soda, or perhaps a bowling ball? The basis for all those fun projects is here.

The center platform is 5" in diameter. Each motor mount surface is 1 5/8" (41.27mm) square and on the same plane as the center component platform. All required parts are included to attach the battery pack mount on top or bottom of platform. Mounts for auxilliary booms are provided if for example you wish to mount a tail fin or place a gimbled camera on a boom between the motor booms. Wire for landing gear is provided. The gear is mounted on the motor mounts. A bending plan is provided. The kit may be configured for flying in either On-Axis (Cruciform or +) or Off Axis (Racecar or X) configuration.

What you get: All parts for center platform including main boom and auxillary boom mounts, 4 motor mounts, battery straps, fasteners/stand offs, wire and bending plan for landing gear.

What you need to add: 2 each 10mm square booms (GWS Slow Stick Booms and woodie arms listed in this category), 4 motors, 4 speed controls, stabilizer board of some sort, battery to match (usually 3S 2100 or so) and receiver.

Mark Harrison's Arcticopter II build log and flight videos. Marks excellent multi-rotor blog site and his use of our Designers Quad Kit and accessories as he evolves his multi-rotor concepts.

LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire battery male single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00.

You can program mix SwitchGlo just as you can program mix any servo on your craft, allowing you to utilize your glow in ways you never thought possible! Low Throttle glow activation is achieved by programming your TX to activate the SwitchGlo channel at any throttle position you desire. You can further enhance your Low Throttle mix by assigning a toggle switch to activate the mix, thereby forever preventing "Hot Starts"

Know when you glow! - SwitchGlo will beep the entire time your glow plug is glowing, providing invaluable reassurance you never thought you needed! SwitchGlo helps you diagnose starting problems; a single beep from SwitchGlo signals the glow/ground loop is open, most often indicating your glow plug is spent. This feature greatly reducing your troubleshooting efforts!

Technology: SwitchGlo Pro is an intelligent and highly efficient on-board glow driver. Its state-of-the-art voltage adaptive algorithm optimizes the power transferred from your battery pack to your glow plug providing the ideal glow. Outfitted with low power components, switched-mode voltage regulation and adjustable firmware, SwitchGlo is not your conventional on-board glow system.

Other on-board glow systems use linear regulators that waste power (up to 3 times as much) and operate at dangerously high temperatures. These linear glow drivers also suffer from low glow at lower pack voltages, while SwitchGlo gives a strong and consistent glow from 4V - 9V. Combining the benefits of switch-mode voltage regulation and the smallest footprints on the market, SwitchGlo Pro is the most advanced way to glow! SwitchGlo Pro draws an insignificant 0.4mAh per 1 second of glow time and will not noticeably drain your receiver battery. Total onboard weight is only 25 grams including the pig tail.

Easy to cut gator off and solder on any plug connector you like, see options in drop down menu. Check out "Glow & Fuel Power Everthing" sub category "Glow Plug Fittings" for varieties. At your Add any of them to your basket and include a note with order that you'd like it added to your SwitchGlo Pro along with wire length you'd like. We'll do the soldering no charge!

Specifications: 

• Dimensions: 1.587" x .720" x .590"
• Receiver cable: 8"
• Glow Plug Pigtail: 8"
• Weight: 28 grams with pigtail
• Input Voltage: 4V - 9V input
• Output Power: 4.8W 

Power Consumption:

•  0.44mah per second of glow time
• 2.2mah per 5 seconds glow (average start)
• 4.4mah per 10 second glow (auto shut-off)
• 33mah to start craft for a typical 15 flights per charge
• Over 2300 average glows on a 5200mah battery (assumes no other battery draw)
• Glow plug average current draw measured at 1.5a

Each package includes two complete push rod systems, so you can set up two control surfaces--such as the elevator and rudder. Everything you need is included, and the parts are designed to work together for simple, clean installation.

Each set contains:

• 2 pushrods with a pre-bent 90? end, ready to use
• 2 pushrod housings that guide the rods and stop them from bending
• 2 Micro E/Z Links for attaching to your control horn
• 2 Mini E/Z Connectors for attaching to your servo arm and making easy adjustments

These components allow for smooth movement with very little friction. They also make it easy to fine-tune your control surfaces so your airplane responds the way you want it to.

The Micro Push Rod System is available in four different weights to fit a wide range of aircraft sizes:

• #847 - 3.2 grams per set
• #852 - 4.6 grams per set
• #922 - 5.7 grams per set
• #941 - 18 grams per set (for slightly larger electric planes)

This system works great on:

• Indoor flyers
• Small park flyers
• Slow flyers
• Foamies and EPP aircraft
• Lightweight scratch-built planes

Installation is quick and beginner-friendly. The housings glue easily to your model, and the connectors make attaching and adjusting your pushrods simple.

Proudly Made in the USA, the DU-BRO Micro Push Rod System provides a dependable and lightweight way to get precise control from your electric RC aircraft.

This item qualifies as a Rod Stock Item, read below:

Rod Stock Policy: In order to include long skinny products at our very favorable shipping rates: All USA orders that contain rod-stock items need to contain at least 6 rods. Rod stock is anything over 30". This would include Music Wire, Carbon Rods of any kind, larger Pushrod kits, brass or aluminum rods and anything else of that nature. Thinner items like carbon strips .5mm thick, sub 1mm diameter carbon rods and music wire .020 or thinner ordered in quantities less than 6 rods total will be shipped coiled. Unless otherwise stated, all carbon rod stock is pull-truded construction grade. The resin is heat cured as the fibers are pulled through a die of the proper shape. Sizes are approximate usually within 5%. Weight is in grams per meter, as per the manufacturer documentation, no guarantees on weight. Find other qualifying items to mix and match to meet the 6PC Minimum Purchase Requirement:

https://www.radicalrc.com/category/Rod-Stock-Policy-Items-634

Deans 3-Pin Male/Female, one set.
Use for Servo, battery or charger connection.
Deans connectors are bulletproof.
All Deans connectors come bare with heat shrink.

Put wires colors where you want, the standard if you want to conform is polarity pin (the offset pin) is signal, center is red (+) and the other outside pin is black (-). We sell and use only Genuine W.S. Deans Plugs.

We sell and use only Genuine W.S. Deans Plugs.

The PowerBox PIK range of connectors exploits modern Hot-Melt technology to combine proven connector systems used in modelling applications.

All the joints in our cables are soldered on our premises, and subsequently checked by a second staff member for correct polarity and quality of workmanship. The connector is then placed in a specially made injection-moulding tool, in which it is encapsulated with a special plastic at a temperature of 220ºC and a pressure of 10 bar.

This process permanently seals the soldered joints as well as acting as a strain relief. Neither mechanical stress nor environmental influences - such as damp or heat - can have any adverse effect on this connection. The plastic we use is resistant to vibration, oxidation, acids, alkalis and fuels, and is temperature-resistant from -30ºC to +90ºC.

The cables we supply include types with different conductor cross-sections, adapters, charge leads and three-core servo leads. Cables with a cross-sectional area of up to 1.0mm have PVC insulation, while the 1.5mm and 2.5 mm types feature silicone insulation.

We are anxious to protect you, our customers, from plagiarists, and for this reason we have registered the design and other quality characteristics of these products in the Design Register of the Deutsches Patent- und Markenamt (German Patent and Brand Office).

(Reference No. DE 40 2010 000 949.5, Rights Holder: PowerBox-Systems GmbH)

10" machine made Silicone pigtails are available in our connector section at lower cost if they can meet your needs.

Note, for a happy life, get your sex right. Servo and battery ends are "MALE", RX's and Y harness receptacles are "FEMALE". When the pins are hidden, connectors are gendered by the shell. Just remember as an assembly, a servo plug fits inside an RX or Extension therefore it's male.

TEMPORARILY OUT OF STOCK 

If you don't mind doing a bit of soldering, the PERS can be easily reversed and assigned a fail-safe setting. The PERS was designed to use the power from your receiver battery, but it can also be configured to use a separate battery, up to 20V. Take a look at the PERS instructions (link below) for reverse/fail-safe settings and wiring diagrams.

The PERS is available with 4 different types of servo connectors to accommodate the various micro receivers available today. Scroll down to view the different options and cart buttons. Packing Note: PERS's ordered in 1pc quantities will come in individual packages. 3 and 10pcs quantities may be supplied in one package with one set of instructions.

Choose your connector option:

PERS with standard Universal/JR servo connector   

This model comes with a standard universal/JR servo lead which will plug into any brand receiver which uses standard servo connectors. The servo lead is 3" of 28AWG wire in Futaba colors, but with a universal connector.

PERS with 1.00mm servo connector for Spektrum AR6400 receivers   

This model comes with a 1.00mm servo lead that will plug into the Spektrum AR6400 and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in JR colors. The PERS is ten times lighter than the AR6400 receiver so it won't noticably affect the weight of your model. In one of the images below you can see the PERS plugged into an AR6400 receiver controlling a high-brightness LED.

PERS with 1.25mm servo connector for Futaba R616FFM micro receivers

This model comes with a 1.25mm servo lead that will plug into the Futaba R616FFM receiver and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in Futaba colors. The PERS is 20 times lighter than the R616FFM receiver so it won't noticably affect the weight of your model.

 PERS with 1.50mm servo connector for Spektrum AR6300 receivers

This model comes with a 1.50mm servo lead that will plug into the Spektrum AR6300 and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in JR colors. The PERS is six times lighter than the AR6300 receiver so it won't noticeably affect the weight of your model.

Receiver Power: 2.0-6.0V

Receiver Current Draw: <1mA (LED off), 5mA (LED on)

Maximum Continous Switch Current: 3.0 amps

Maximum Momentary (<2s) Switch Current: 4.0 amps

Maximum Switch Voltage: 20.0V (see instructions for using a separate battery)

Circuit size not including wires: 7.7 x 6.2 x 3.4mm (0.30 x 0.24 x 0.13in)

Specs - Universal Connector

Weight without output wires: 0.85g (0.030oz)

Weight with 6" output wires: 1.14g (0.040oz)

Overall length with 6" output wires: 23.7cm (9.25in)

Receiver connection: Universal/JR 0.1" connector, 3" 28AWG Futaba color wire

Specs - All Other Connectors

Weight without output wires: 0.30g (0.011oz)

Weight with 6" output wires: 0.59g (0.021oz)

Overall length with 6" output wires: 18.0cm (7.0in)

Receiver connection: 1.00mm / 1.25mm / 1.50mm, 1" 30 AWG wire