3-pole male pigtail JST Micro White connector. Used by battery on Plantraco RX, servos for Wes Technic, JST GWS RX's and is the same connector used on Spektrum/JR satellite remote RX extensions. Comes with 26 gauge wire. White in color.
LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two & three wire battery male single end leads/pigtails are quantity of 5 for $8, regularly $2 each. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00.
How it works: SwitchGlo Pro simply plugs into a receiver channel, then to your glow plug. You assign a transmitter toggle switch to this SwitchGlo channel, and toggle your glow on and off, at startup or in-flight.
You can program mix SwitchGlo just as you can program mix any servo on your craft, allowing you to utilize your glow in ways you never thought possible! Low Throttle glow activation is achieved by programming your TX to activate the SwitchGlo channel at any throttle position you desire. You can further enhance your Low Throttle mix by assigning a toggle switch to activate the mix, thereby forever preventing "Hot Starts"
Know when you glow! - SwitchGlo will beep the entire time your glow plug is glowing, providing invaluable reassurance you never thought you needed! SwitchGlo helps you diagnose starting problems; a single beep from SwitchGlo signals the glow/ground loop is open, most often indicating your glow plug is spent. This feature greatly reducing your troubleshooting efforts!
Technology: SwitchGlo Pro is an intelligent and highly efficient on-board glow driver. Its state-of-the-art voltage adaptive algorithm optimizes the power transferred from your battery pack to your glow plug providing the ideal glow. Outfitted with low power components, switched-mode voltage regulation and adjustable firmware, SwitchGlo is not your conventional on-board glow system.
Other on-board glow systems use linear regulators that waste power (up to 3 times as much) and operate at dangerously high temperatures. These linear glow drivers also suffer from low glow at lower pack voltages, while SwitchGlo gives a strong and consistent glow from 4V - 9V. Combining the benefits of switch-mode voltage regulation and the smallest footprints on the market, SwitchGlo Pro is the most advanced way to glow! SwitchGlo Pro draws an insignificant 0.4mAh per 1 second of glow time and will not noticeably drain your receiver battery. Total onboard weight is only 25 grams including the pig tail.
Easy to cut gator off and solder on any plug connector you like, see options in drop down menu. Check out "Glow & Fuel Power Everthing" sub category "Glow Plug Fittings" for varieties. At your Add any of them to your basket and include a note with order that you'd like it added to your SwitchGlo Pro along with wire length you'd like. We'll do the soldering no charge!
Specifications:
Dimensions: 1.587" x .720" x .590"
Receiver cable: 8"
Glow Plug Pigtail: 8"
Weight: 28 grams with pigtail
Input Voltage: 4V - 9V input
Output Power: 4.8W
Power Consumption:
0.44mah per second of glow time
2.2mah per 5 seconds glow (average start)
4.4mah per 10 second glow (auto shut-off)
33mah to start craft for a typical 15 flights per charge
Over 2300 average glows on a 5200mah battery (assumes no other battery draw)
And you thought the story about aliens at Wright Patt was just a conspiracy theory? At long last, a durable light weight quad copter airframe kit. This kit makes use of basic 10mm square carbon, fiberglass or aluminum tubes. All of our 10mm boom based Slow Stick hopups such as servo mounts, battery tray's, gear mounts and etc.... are compatible with our Quad Coper Designers Kit.
By making use of different motor systems and different boom lengths, you can make a quad of any size you like up to 1 meter (39") frame OD. Our motor mounts are light enough for small outrunners and strong enough for even 28mm size outrunners. You can use this kit as the basis for your special project. Want to carry your GoPro camera to get that special shot? Want to build a Quad FPV? Want to deliver a can of soda, or perhaps a bowling ball? The basis for all those fun projects is here.
The center platform is 5" in diameter. Each motor mount surface is 1 5/8" (41.27mm) square and on the same plane as the center component platform. All required parts are included to attach the battery pack mount on top or bottom of platform. Mounts for auxilliary booms are provided if for example you wish to mount a tail fin or place a gimbled camera on a boom between the motor booms. Wire for landing gear is provided. The gear is mounted on the motor mounts. A bending plan is provided. The kit may be configured for flying in either On-Axis (Cruciform or +) or Off Axis (Racecar or X) configuration.
What you get: All parts for center platform including main boom and auxillary boom mounts, 4 motor mounts, battery straps, fasteners/stand offs, wire and bending plan for landing gear.
What you need to add: 2 each 10mm square booms (GWS Slow Stick Booms and woodie arms listed in this category), 4 motors, 4 speed controls, stabilizer board of some sort, battery to match (usually 3S 2100 or so) and receiver.
Deans 3-Pin Male/Female, one set. Use for Servo, battery or charger connection. Deans connectors are bulletproof. All Deans connectors come bare with heat shrink.
Put wires colors where you want, the standard if you want to conform is polarity pin (the offset pin) is signal, center is red (+) and the other outside pin is black (-). We sell and use only Genuine W.S. Deans Plugs.
PowerBox Systems Charging Lead Deans type, silicone wire 1.5mm, 40cm Long. Also includes the connectors made by the American Deans company. We use only original Deans plugs and sockets for these connectors. Features: Heavy-duty insulation of soldered joints Excellent long-term functional properties Soldered joints immune from oxidation Vibration protection Kink protection Resistant to chemical influences Temperature-resistant from -30°C to +90ºC
The PowerBox PIK range of connectors exploits modern Hot-Melt technology to combine proven connector systems used in modelling applications.
All the joints in our cables are soldered on our premises, and subsequently checked by a second staff member for correct polarity and quality of workmanship. The connector is then placed in a specially made injection-moulding tool, in which it is encapsulated with a special plastic at a temperature of 220ºC and a pressure of 10 bar.
This process permanently seals the soldered joints as well as acting as a strain relief. Neither mechanical stress nor environmental influences - such as damp or heat - can have any adverse effect on this connection. The plastic we use is resistant to vibration, oxidation, acids, alkalis and fuels, and is temperature-resistant from -30ºC to +90ºC.
The cables we supply include types with different conductor cross-sections, adapters, charge leads and three-core servo leads. Cables with a cross-sectional area of up to 1.0mm have PVC insulation, while the 1.5mm and 2.5 mm types feature silicone insulation.
We are anxious to protect you, our customers, from plagiarists, and for this reason we have registered the design and other quality characteristics of these products in the Design Register of the Deutsches Patent- und Markenamt (German Patent and Brand Office).
(Reference No. DE 40 2010 000 949.5, Rights Holder: PowerBox-Systems GmbH)
We can hand make pigtails to almost any specification. A "Pigtial" has a connector on only one end. Silicone 20 gauge are as heavy as you can get and have the added bonus of being very flexible and heat resistant. Use to repair servos, switch harnesses or perhaps add to existing servos for that "Extension Free" custom instalation. Choose from drop down menus your preferences. Generally we size these by measuring from the back of each connector. So the overall length will be greater by connector shell length. Twisted wire can be adjusted slightly in length by changing the number of twists. We try to get within about 1/2" of your spec. Please order long enough to compensate for minor variance.
10" machine made Silicone pigtails are available in our connector section at lower cost if they can meet your needs.
Note, for a happy life, get your sex right. Servo and battery ends are "MALE", RX's and Y harness receptacles are "FEMALE". When the pins are hidden, connectors are gendered by the shell. Just remember as an assembly, a servo plug fits inside an RX or Extension therefore it's male.
The PERS is a very tiny receiver-actuated on/off switch. It plugs into one of your receiver channels and lets you turn a device on/off using a stick, switch, or knob on your transmitter. The PERS performs the operation equivalent to a servo moving a mechanical switch back and forth, but in a much smaller package, and with no moving parts! The PERS will operate with any receiver running on 2-6V and can switch on/off pretty much any device up to 3A of current. The PERS is perfect for lights, glow plug drivers, motors, smoke pumps, rocket igniters, solenoids, relays, and whatever else you can think up. Wired correctly, it could be used to trigger cameras or other electronic devices. The PERS weighs just 0.3g, not including the 6" output wires (if left full-length these wires weigh another 0.3g).
If you don't mind doing a bit of soldering, the PERS can be easily reversed and assigned a fail-safe setting. The PERS was designed to use the power from your receiver battery, but it can also be configured to use a separate battery, up to 20V. Take a look at the PERS instructions (link below) for reverse/fail-safe settings and wiring diagrams.
The PERS is available with 4 different types of servo connectors to accommodate the various micro receivers available today. Scroll down to view the different options and cart buttons. Packing Note: PERS's ordered in 1pc quantities will come in individual packages. 3 and 10pcs quantities may be supplied in one package with one set of instructions.
Choose your connector option:
PERS with standard Universal/JR servo connector
This model comes with a standard universal/JR servo lead which will plug into any brand receiver which uses standard servo connectors. The servo lead is 3" of 28AWG wire in Futaba colors, but with a universal connector.
PERS with 1.00mm servo connector for Spektrum AR6400 receivers
This model comes with a 1.00mm servo lead that will plug into the Spektrum AR6400 and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in JR colors. The PERS is ten times lighter than the AR6400 receiver so it won't noticably affect the weight of your model. In one of the images below you can see the PERS plugged into an AR6400 receiver controlling a high-brightness LED.
PERS with 1.25mm servo connector for Futaba R616FFM micro receivers
This model comes with a 1.25mm servo lead that will plug into the Futaba R616FFM receiver and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in Futaba colors. The PERS is 20 times lighter than the R616FFM receiver so it won't noticably affect the weight of your model.
PERS with 1.50mm servo connector for Spektrum AR6300 receivers
This model comes with a 1.50mm servo lead that will plug into the Spektrum AR6300 and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in JR colors. The PERS is six times lighter than the AR6300 receiver so it won't noticeably affect the weight of your model.
Specs:
Receiver Power: 2.0-6.0V
Receiver Current Draw: <1mA (LED off), 5mA (LED on)
Maximum Continous Switch Current: 3.0 amps
Maximum Momentary (<2s) Switch Current: 4.0 amps
Maximum Switch Voltage: 20.0V (see instructions for using a separate battery)
Circuit size not including wires: 7.7 x 6.2 x 3.4mm (0.30 x 0.24 x 0.13in)
Specs - Universal Connector
Weight without output wires: 0.85g (0.030oz)
Weight with 6" output wires: 1.14g (0.040oz)
Overall length with 6" output wires: 23.7cm (9.25in)
Receiver connection: Universal/JR 0.1" connector, 3" 28AWG Futaba color wire
Specs - All Other Connectors
Weight without output wires: 0.30g (0.011oz)
Weight with 6" output wires: 0.59g (0.021oz)
Overall length with 6" output wires: 18.0cm (7.0in)
The DU-BRO Micro Push Rod System is a lightweight and easy-to-install control linkage designed for small to medium electric RC airplanes. It gives you smooth, accurate control while keeping the weight of your model as low as possible. This makes it perfect for foamies, indoor planes, park flyers, and small electric aerobatic models.
Each package includes two complete push rod systems, so you can set up two control surfaces--such as the elevator and rudder. Everything you need is included, and the parts are designed to work together for simple, clean installation.
Each set contains:
2 pushrods with a pre-bent 90? end, ready to use
2 pushrod housings that guide the rods and stop them from bending
2 Micro E/Z Links for attaching to your control horn
2 Mini E/Z Connectors for attaching to your servo arm and making easy adjustments
These components allow for smooth movement with very little friction. They also make it easy to fine-tune your control surfaces so your airplane responds the way you want it to.
The Micro Push Rod System is available in four different weights to fit a wide range of aircraft sizes:
#847 - 3.2 grams per set
#852 - 4.6 grams per set
#922 - 5.7 grams per set
#941 - 18 grams per set (for slightly larger electric planes)
This system works great on:
Indoor flyers
Small park flyers
Slow flyers
Foamies and EPP aircraft
Lightweight scratch-built planes
Installation is quick and beginner-friendly. The housings glue easily to your model, and the connectors make attaching and adjusting your pushrods simple.
Proudly Made in the USA, the DU-BRO Micro Push Rod System provides a dependable and lightweight way to get precise control from your electric RC aircraft.
This item qualifies as a Rod Stock Item, read below:
Rod Stock Policy: In order to include long skinny products at our very favorable shipping rates: All USA orders that contain rod-stock items need to contain at least 6 rods. Rod stock is anything over 30". This would include Music Wire, Carbon Rods of any kind, larger Pushrod kits, brass or aluminum rods and anything else of that nature. Thinner items like carbon strips .5mm thick, sub 1mm diameter carbon rods and music wire .020 or thinner ordered in quantities less than 6 rods total will be shipped coiled. Unless otherwise stated, all carbon rod stock is pull-truded construction grade. The resin is heat cured as the fibers are pulled through a die of the proper shape. Sizes are approximate usually within 5%. Weight is in grams per meter, as per the manufacturer documentation, no guarantees on weight. Find other qualifying items to mix and match to meet the 6PC Minimum Purchase Requirement:
The ParkBEC 6V is the 6 volt output version of our ParkBEC, the smallest and lightest switch-mode BEC on the market. The 6 volt output will give you more servo speed and torque than standard 5V models. It can support as many as six sub-micro servos. ParkBEC 6V is especially well suited for small helicopters and 3d planes, where extra response speed or torque are needed. It weighs only 6.5g and is designed for running parkflyer type aircraft with pack voltages up to 33.6V. The ParkBEC 6V installs between your ESC and receiver. You don't have to modify your speed control to disable its internal BEC, just plug the ESC into the ParkBEC 6V. It uses a switching type power supply to efficiently convert high pack voltages into a steady 6 volts. Additional notes If you are using small servos make sure they can run at 6v. Some sub-micros, notably the Hitec HS-50 and Futaba S3154, can be damaged by a 6v supply. For best results, ensure that the ParkBEC 6V is installed at least 2 inches away from your receiver and antenna. ParkBEC 6V is not compatible with 2s lithium packs. ParkBEC 6V cannot power multiple digital servos. Product Specs Model: ParkBEC 6V Specifications: Input voltage: 8V to 33.6v (3s-8s lithium, up to 21 NiMHs) Output current: 1.25A continuous, 1.5A 60 second peak. (6 4-9g servos, 4 standard servos) Weight: 6.5g/.23oz Weight Without Wires: 4.4g/.16oz 6 Volt output Universal connector fits all receivers 1.3V dropout voltage at 1A Can be put in parallel Applications: Parkflyers Small 3d aircraft Micro helicopters Robots
Discontinued by Manufacturer, while supplies last! Also see SportBEC
Long Arm Y harness. Great to drive 2 aileron or flap servos from the same channel in a large wing. Eliminates risk and weight of all those extra hidden connectors you'd have if you piece together a bunch of stock sizes. Here is a special part to solve some of those special problems. The Leg is 6" for all sizes. Arms (to plug servos into) are variable length. Length below is for each arm so 24" Long Arm Y has 48" spread. Size choice is length of each arm from y joint. Pick your size below. 22 gauge heavy duty wire. Note: JR harnesses on left and Futaba J on right. SKU Number: RRCY06L__AFJ
Y harness. Aprox. 10" long. Use to run two servos off one channel output on RX. Futaba 'G' connector style (old), standard twisted red/white wire. SKU Number: RRCY12HDFG
Fast, but not too fast. Maneuverable, but not tricky. A snap to build and surprisingly rugged compared to most. The original Sunday Fighters were the brainchild of Ken Willard back in the early 1970's. His were small, .049 powered 3-channel models and proved quite popular. Now, we've taken this idea, enlarged, and re-engineered them to make them as much fun to build as they are to fly.
You should see them take evasive maneuvers in Dog Fighting. Evade with snap rolls into spins, Immelmann turns and a loop. Our radio-controlled Sunday Fighter airplane kits just might be the most fun you've had in a long time.
Because of the interlocking design and high quality laser cutting of the parts, the Sunday Fighter is a quick build. Not only does it build quick, but it also builds straight and true as all of the parts are designed to align properly with a minimum of fuss and alignment tools.
The wings are removable for storage/transport and for giving access to the extra large cabin area. From there you have easy access to install most any brand of radio and control linkages. However, the fully assembled model can fit in the trunk of most mid-sized cars.
Up-front, we've designed in a hatch that covers the battery/tank compartment. This area will easily handle 3s packs and 6 ounce tanks.
Whether you choose to power your Sunday with electric or glow power, we've got you covered. Glow engines can be mounted side, inverted or even upright with a little modification. Electric motors can be mounted using the included Motor Box which will help space your motor to the proper distance.
Go true "old-school" with 3 channel control, or opt for functional ailerons (4 channel).
There are two Sunday Fighters - the German version you see here, and the British version you can see at this link.
Specifications:
Wingspan: 46.5 inches
Wing Area: 725 sq inches
Length (airframe only): 34 inches
Weight: 3.5 - 4 pounds
Radio: 3-4 channel system
Power:
o Glow (.20-.30 engine, 6 ounce tank, fuel tubing)
o Electric (equivalent brushless motor, 3s LiPo)
Premium USA Hardware
Included in each Old School Model Works kit is a premium hardware package. We only source our hardware from brand-name, USA manufacturers to guarantee the best quality.
Dual Ailerons Mounted under the lower wing, these two pre-cut aileron hatches make it easy to install the aileron servos.
WEB-LOCK Construction There's nothing else like it. Build our wings, straight and true - with a minimum amount of fuss.
Bolt on main gear Bending your own landing gear is hard. So that's why we include pre-bent main landing gear wire ready for you to assemble.
Front hatch Held in with magnets, this extra hatch gives you easy access to batteries or fuel.
Included Motor Box For electric power, we include the pieces to build this electric motor mounting box.
Design your color scheme Download this sheet to design your Heinschmitt's color scheme.
Additional items needed to complete our Sunday Fighter kit:
o Propeller
o Engine/Motor mount & mounting hardware
o 2-5 servos depending on setup: 2 mini for elevator/rudder, 2 Sub-Micro for ailerons/throttle
o "Y" servo harness (for ailerons)
o Pushrods (two 5" for ailerons, two 20" for elevator & rudder, one 9" for throttle if glow powered)
o Clevises for the pushrods (8 if electric, 10 if glow).
o 2 - 3.5" diameter wheels. We recommend Du-Bro's #350V Vintage wheels for the proper look.
o 1 - tailwheel assembly
o Covering
Flickr Album
Due to high demand, allow at least 2 weeks or more for shipment.
DELight Ultra Bright LEDs pair. Powerful, easy to use LED lights which are designed to be used with the DELight Controller. Fully self-contained, can be used by themselves if desired. Standard servo-type plug, so you can use off-the-shelf servo extensions and Y-harnesses. Each LED puts ot 15 lumens of light, which is more than a child's night-light. They have a wide 120 degree beam angle, so they can be seen from many positions and light up large surfaces. Each module consists of a half-watt surface mount LED, an appropriate current-limit resistor and a 24" lightweight wire pigtail terminating in a universal servo-type connector. Available colors are currently red, green and white. Product Specs: Operating voltage: 4V-6V Current: 150mA max Size: .2" x .375" x .125" + 24" Wire Pigtail Weight: 2.8 g Applications: Additional LEDs for the DELight Programmable Lighting System Model Lighting Theatrical Light Effects Night Flying
2 Wire battery female as found on the battery input lead of a switch harness or the end of a charge cord. This plug will accept the male connector on a stock RX battery pack. This item is a 26 gauge which is similar to what you find on many factory stock switch harnesses. I consider it light duty, use on charge cords or in smaller low servo count models. Twisted Wire. SKU Number: RRC2PPFJR26GTIG
Slip over horn with adjustment wheel collar as shown in photo. This is a complete set of adjustable horns that slip over the wire. Your aileron pushrod connects to this part. Simplifies servo link hook-ups. Includes (2) 3-32 Dura-Collars, (2) Nylon Horn Connectors, and (2) 4-40 x 1/8 Slotted Screws. For .093 wire. (QTY/PKG: 2 ) Weight: 3 grams/set (1.5 grams/each). SKU Number: DUB103
Celebrating Sig's Golden Anniversary, they are ecstatic to introduce the latest addition to their line of high quality Build It Yourself airplane kits: the 1/5 Scale J-3 Piper Cub..
They've put everything they've learned about model airplanes into this special kit: scale details, Sig laser cut parts, full size plans, a comprehensive instruction booklet. All the features you've come to expect from Sig. Then they added a little something special. The new 1/5 Scale J-3 Piper Cub is so real, you may have a hard time separating it from the 1930's full size airplane. All of the details are included - a working side door and window, dummy engine cowls with "eyebrows", scale-like wire landing gear, a fully detailed instrument panel... even the realistic "bird's eye-view" window on top of the cabin. Add in a full decal sheet including Cub lightning bolts and you have a Cub standing far above the rest.
Specifications: Wingspan 84.5 in 2146 mm Wing Area 947 sq in 61.1 sq dm Weight 7 lb 3175 g Length 55.25 in 1403 mm Radio Required 4-Channel, 5 Servos
Recommended Engines .40 - .46 cu in (6.5 - 7.5 cu cm) 2-Stroke .45 - .65 cu in (7.5 - 10.7 cu cm) 4-stroke
Kit Features 90% laser cut parts for accuracy and ease of assembly Windshield and engine cylinders Quality SIG AAA balsa and plywood A super tough scale-like tail wheel assembly Full size plans Molded plastic parts for windows Fiberglass cowling A full compliment of quality SIG hardware Fully illustrated manual to guide you from box to completion
Additional items required: 4 channel radio system with 5 standard servos .40-.46 2 stroke or .45-.65 4 stroke glow engine Propeller to fit engine 1 piece fuel tubing - SIGSH286 1 piece 12 ounce fuel tank - SUL429 2 pieces 3-3/8 inch main wheels - DUB338TC 1 piece 1 inch tail wheel - DUB100TW 4 rolls covering material Optional DuBro Fuel Valve - DUB334
Tools Required: Thin CA Adhesive Medium CA Adhesive Modeling knife with #11 blades Drill with bits Dremel Moto Tool with bits Sanding Block Sandpaper - Assorted Grits T Pins
Temporarily out of stock, pending manufacturer production
This material shrinks easily with your covering shrink gun, lighter or other heat source. After shrinking, this higher quality tube stays flexible keeping your strain relief plans intact. Shrinks about 50%. 1/16 and 3/32 sizes are most popular for individual servo and park flier pack wires. 1/8" for strain relief on 2 pole 22 gauge battery pack wire, larger sizes for larger wire. Shown at right is 3/8" for locking together servo connectors you won't be able to easily inspect later.
Measurement is inside diameter: 1/4" / .25" / 6.4mm
Very economical to keep plenty of this material on hand. You'll find many uses, we even use the smallest size for wheel collars on some of our kits! Sold in multiples of 3' lengths. SKU Number: WS06.4R
The Talon 60 is well suited for SMALL SCALE OR AEROBATIC HELIS ranging from 360-450 size requiring up to 1400 watts on 6S. This ESC offers Castle's industry-leading helicopter functions, such as the remarkable direct entry governor mode. Simply type in the desired RPM using a Castle Link USB adapter (redeemable coupon enclosed with purchase) and the free Castle Link Programming Suite running on a Windows (TM) PC.
The compact layout and slim profile of the Talon 60 is also perfect for SCALE, SPORT and AEROBATIC PLANES in the .32 - .60 range requiring up to 1400 watts on 6S. Mounting the Talon 60 is simple and stress-free in any setup.
The Talon series ESCs are known for sporting heavy-duty BEC's designed for today's servos. The Talon 60 is no exception. With its 20 AMP PEAK POWER and 8 AMPS OF CONTINUOUS POWER, it will keep even the most draining servos at ease.
CASTLE-LINK(TM)
For nearly 20 years Castle engineers have been setting the bar for industry leading software functionality. The Castle Link Programming Suite is the ticket to creating the perfect setup. Gaining access to the host of tuning parameters, including free firmware updates and added feature sets, requires only the Castle Link USB adapter (redeemable coupon enclosed with purchase) and the free Castle Link software on your Windows (TM) PC. Users can then fine tune many variables to enhance their level of expertise.
Power System Alerts
The Talon ESCs are programmed to sound a number of tunes and codes using the motor as well as flashing LED patterns to alert users to certain conditions regarding their power system, such as over temperature, excessive load and locked head speed.
Telemetry Capable
Telemetry has the potential not only to improve the safety of our models by monitoring battery voltages, ESC temperature, and other critical parameters, but it also creates other opportunities to get even more fun out of flying because you've essentially reduced the risks of "unknown" inevitable crashes. Think of the benefits to be had from alarms that will sound to warn you when there's interference about or if your receiver battery is running unexpectedly low. Requires purchase of Castle Telemetry Link for S.BUS2 (Item # 010-0152-00) and compatible Futaba Radio or Castle Telemetry Link for X-BUS (Item# 010-0148-00) and a compatible Spektrum Radio.
The TALON 60 is PROUDLY DESIGNED, MANUFACTURED AND SUPPORTED IN OLATHE, KANSAS, and is backed by Castle Creations' 1-year warranty and unparalleled 'make-it-right' customer support.
Technical Specs
Input Voltage Range: MIN: 2S LiPo
MAX: 6S LiPo
Max Continuous Amperage at full throttle: 60 amps*
Max Voltage: 25.2V
BEC Voltage: User selectable choice of 6 or 8 volt output (default is 6V).
BEC Output: 20 amp peak** , 8 amp continuous
Size: Width: 1.19" (30.2mm)
Length: 2.56" (65mm)
Depth: 0.41" (10.6mm)
Weight : 2.05 oz. (57 g) with wires
1.09 oz. (g) without wires
Connectors: N/A
Items Needed for Operation: Battery and Motor connectors sold separately.
Tools needed for installation: Soldering iron for attaching High Current bullet connectors to ESC, motor, and battery. (Deans Ultra Plugs, EC5 or Castle Polarized 4mm or 6.5mm)
Application Guidelines: SMALL SCALE OR AEROBATIC HELIS ranging from 360-450 size requiring up to 1400 watts on 6S and SCALE, SPORT and AEROBATIC PLANES in the .32 -. 60 range requiring up to 1400 watts on 6S.
Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Castle Link adapter included in package) and freely downloadable Castle Link Windows software. (A small subset of the settings available through Castle Link Windows software can be accessed via manual programming through the transmitter stick.)
1/32 aircraft ply small laser horns. Mounting surface area on these are idealy suited to models with 3/32 to 1/4" thick control surfaces. These horns have holes correct for 1/32 wire used in all the smallest servos such as GWS Pico/Naro, HS-50, PS-20. HE490, HE2003, MX30 and many others. kits. Install horns in a slot in surface, because of the large contact area, they won't wobble like plastic pin type horns do. This results in finer better control and fewer trim changes in flight. 8 horns per package. SKU Number: RRCLH32SM
Handy set of 8 black nylon keepers. Fits .055" (1.5mm) push rod wire most commonly used in park fliers and foamys. Black nylon material. Simply bend the end of your pushrod into an "L". Put the L through the servo or control horn. Bend the hand back and clip onto the rod. Simple use, removes and instals quickly. Keeps your push rods from slipping out of the control horns. Light weight, simple and they work great!
Photo shows an example of our "Flexi-Keeper" hooked to end of push rod and a control horn.
This material shrinks easily with your covering shrink gun, lighter or other heat source. After shrinking, this higher quality tube stays flexible keeping your strain relief plans intact. Shrinks about 50%. 1/16 and 3/32 sizes are most popular for individual servo and park flier pack wires. 1/8" for strain relief on 2 pole 22 gauge battery pack wire, larger sizes for larger wire. Shown at right is 3/8" for locking together servo connectors you won't be able to easily inspect later. Measurement is inside diameter. Sold in multiples of 2' lengths. SKU Number: WS30B
 "RRC Extension Harness 78\" (200cm) Buffered/Filtered JR")
 "3-Pole FJ Wire Pigtail w/Male JST Micro White")
 "SwitchGlo Pro")
 "Radical RC Quad Copter Designers Kit")
 "DEANS 3-Pin Connector One Pair")
 "PowerBox Systems Charging Lead Deans, silicone wire 1.5mm, 40cm Long")
 "Hansen Hobbies PERS V2- Pico Electronic Receiver & Accessory Switch")
 "Du-Bro 30\" Micro2 Pushrod System #922 (30\" x .047\") 2-Pack")
 "Dimension Engineering ParkBEC 6V ~WHILE SUPPLIES LAST!")
 "Super Y Harness, Long Arm Futaba J")
 "Servo Y Harness Futaba G (old)")
 "Old School Model Works German Sunday Fighter Heinschmitt Kit")
 "Dimension Engineering DELight Ultra Bright LED White")
 "Savox SV-1270TG High Voltage, \"Monster Torque\", Titanium Gear, Digital Servo")
 "Savox SC-0251MG High Torque, Metal Gear, Digital Servo")
 "Old Airtronics Servo Extension Harness 10\"")
 "Single End 2 Wire Battery Female 26 Gauge Twisted JR/Hitec/Airtronics Z(new) Style")
 "Du-Bro Strip Aileron Torque Rod Horn Set Only")
 "Sig Anniversary Piper J3 Cub 1/5 Scale Kit")
 "1/4\"/6.4mm Flexible Shrink Tubing for Wires, 3-Foot PC RED")
 "Castle Creations Talon 60")
 "Small Laser Control Horns for 1/32 wire")
 "Radical RC Flexi-Keepers .055\" (1.5mm) Wire L Bends 8 Pack")
 "1-3/16\"/30mm Flexible Shrink Tubing for Wires, 1-Foot Pc Black")
