|
|
Our F3P biased servo horn used by many top competition pilots. 4 peices per sheet. Control Radius .625" (Equivelant to 1.25" spread servo horn). 6 Holes are offset in 6 degree steps starting at 5 degrees and ending at 35 degrees. Holes are precision drilled at .031 to be snug zero slop fit to common .032 pin control rod fittings and music wire. May be sewn and glued to many standard horns. Laser cut from 1/32 aircraft grade plywood. Strong and light weight. I've never had a report of a broken horn. SKU Number: RRCF3PBSH2
|
|
|
|
|
Our F3P biased servo horn used by many top competition pilots. 4 peices per sheet. Control Radius .625" (Equivelant to 1.25" spread servo horn). 6 Holes are offset in 6 degree steps starting at 5 degrees and ending at 35 degrees. Holes are precision drilled at .031 to be snug zero slop fit to common .032 pin control rod fittings and music wire. May be sewn and glued to many standard horns. Laser cut from .020 Fiberglass. Strong and light weight. I've never had a report of a broken horn. Designed in conjunction with Scott Barnhart. SKU Number: RRCF3PBSH2FG
|
|
|
|
|
8 each of our Micro Pull Pull Tension Adjusters. Alows you to loop your pull pull string through a horn then back to this adjuster which can be slipped and locked along the lenght of the cord running to the horn. Works like a tent pole rope adjuster. Use on F3P and other small models with pull-pull control functions. A very difficult part to make by hand simplified for you here. SKU Number: RRCMPPTA
|
|
|
|
|
FEATURES: Black plastic construction Designed for medium size Park Flyers and indoor models SKU Number: DUB936
|
|
|
|
|
Great for indoor and micro park flyers! A pack of 10 pcs. Approximately 7/16" long horn. Black nylon. SKU Number: RRCMCH
|
|
|
|
|
Du-Bro part with fasteners. Made to accept clevis pins typical in 2-56 hardware. Use anywhere you want a shorter horn, not just for 1/2A size models. 2 complete units per package. SKU Number: DUB107
|
|
|
|
|
Du-Bro Control Horn set. 1 1/16" working height/length. Molded from Nylon, left and right handed flange mount with nut plate. Complete with fasteners for easy installation. 2 per pkg. SKU Number: DUB105
|
|
|
|
|
Du-Bro Stronger than conventional nylon control horns, these aerodynamically designed Super Strong control horns come complete with back plate and 2-56 x 1/2" socket head cap screws for easy installation. 1 3/4" (44.45 mm) long with 5 adjustment positions. 2 complete units per package. SKU Number: DUB716
|
|
|
|
|
1 3/8 Long with 5 adjustment positions. Each set incluees 2 control horns that are center on base, 2 self threading nut plates and (4) 2-56 x 5/8 screws. TEMPORARILY OUT OF STOCK SKU Number: DUB237
|
|
|
|
|
These large scale T-Style control horns were aerodynamically designed with large scale planes in mind. 1 3/8 long with 4 adjustment positions and 4 mounting holes. Comes complete with back plate and (4) 4-40 x 1 Socket Head Cap Screws. 2 complete units per package. SKU Number: DUB366
|
|
|
|
|
Set of five control horns, for control surfaces. Opaque fiberglass material. Precision cut. Mounting surface area on these are idealy suited to models with 3/32 to 1/4" thick control surfaces. These horns have pre-drilled holes correct for 1/32 wire which is used in most park flier and F3P applications. Upper right hand horn in photo. SKU Number: RRCFGCH13
|
|
|
|
|
Set of five control horns, for control surfaces. Opaque fiberglass material. Precision cut. Mounting surface area on these are idealy suited to models with 3/32 to 1/4" thick control surfaces. These horns have pre-drilled holes correct for 1/32 wire which is used in most park flier and F3P applications. Lower left hand horn in photo. SKU Number: RRCFGCH16
|
|
|
|
|
Set of five control horns, for control surfaces. Opaque fiberglass material. Precision cut. Mounting surface area on these are idealy suited to models with 3/32 to 1/4" thick control surfaces. These horns have pre-drilled holes correct for 1/32 wire which is used in most park flier and F3P applications. Lower right hand horn in photo. SKU Number: RRCFGCH19
|
|
|
|
|
Large size horn useful for all control surfaces. Drilled for #2-56 (or 2mm) bolt-on ball joints. May be enlarged. Mounting flange drilled for #2 fasteners, may also be enlarged. Solid glass filled horn. May come in CB Associates or B&B Specialties packaging. Bushings for small clevis pins not included. This horn is intended for large control rod hardware. #2 fasteners minimum. SKU Number: CB5546
|
|
|
|
|
Custom designed for F3P competition aircraft and similar foamies. This set contains all the most popular parts from our full rod and shink set. No bipe aileron transfer horns or stand offs in this set. Our ever popular #1 biased control horn for your center aileron servo is included. We thank Seth Arnold for flying our F3P horn sets to victory at the 2009 ETOC. The "Y" horn is for those that prefer a pull-pull rudder setup. Included is a set of 4 micro tension adjusters for your pull-pull lines. The adjusters allow you to loom up your lines like a tent line so you can adjust the tension of your control strings as weather and temperature demands. Note the extra special Biased Servo Horn. This can be screwed or sewn to many common micro dual arm servo horns. Normally the aileron control horns are a bit farther apart than the spread of a stock servo horn. The Biased horn allows you to connect your aileron pushrod so that the rod is 90 degrees to the horn eliminating differential movement the stock horn would cause. This package is sure to save you 2-3 hours of fiddly cutting, sanding and filing. ;-) Lets get busy and get some building done! SKU Number: RRCLHF3PR&SB
|
|
|
|
|
Think BIG!! These HD Adjustable Control Horns are the latest in a family of innovative control horn applications. The self-adjusting horn will mount straight (90? to center line of control surface) against the angled control surface using no wedges or shims! With two sizes available, your aircraft will be even more functional as well as stylish. Intended for .91 and above aircraft. 2 complete units in each package. SKU Number: DUB913
|
|
|
|
|
2 units per package complete with bases and fasteners. Nice 3 bolt aero shape base. Intended for 4-40 (or 2.5mm) thru-bolt ball joint type clevis ends. SKU Number: MPJ2220B
|
|
|
|
|
One complete units with all fasteners and snap pin included. Excellent quality gear. For extra nap pins, order MPJ2234. SKU Number: MPJ2230B
|
|
|
|
|
Two complete units with all fasteners and snap pins included. Excellent quality gear. For extra snap pins, order MPJ2234. TEMPORARILY OUT OF STOCK SKU Number: MPJ2231B
|
|
|
|
|
One complete units with all fasteners and snap pin included. Excellent quality gear. For extra nap pins, order MPJ2234. SKU Number: MPJ2232B
|
|
|
|
|
Two complete units with all fasteners and snap pins included. Excellent quality gear. For extra nap pins, order MPJ2234. Comes in Black and White, choose below. BLACK COLOR IS TEMPORARILY OUT OF STOCK, NEW ORDERS FOR BLACK WILL BE BACKORDERED SKU Number: MPJ2233
|
|
|
|
|
Package of 10 each extra Snap Pins for MPJ2230,2231,2232,2233 small, short and long control horns. SKU Number: MPJ2234
|
|
|
|
|
Micro horn for smaller models. Glue into slot in control surface. Drilled for .039 (1mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. In the size range of park flyer and indoor pushrods all over the world. 2 per package. TEMPORARILY OUT OF STOCK SKU Number: MPJ2200B
|
|
|
|
|
Micro horn for smaller models. Glue into two punctures in control surface. Drilled for .025" (.6mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. Typical size for indoor pushrods all over the world. 2 per package. SKU Number: MPJ2201B
|
|
|
|
|
Micro horn for smaller models. Glue into two punctures in control surface. Drilled for .032" (.8mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. Typical size for indoor pushrods all over the world. 2 per package. SKU Number: MPJ2202B
|
|
|
|
|
Micro horn for smaller models. Glue into two punctures in control surface. Drilled for .025" (.6mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. Typical size for indoor pushrods all over the world. 2 per package. SKU Number: MPJ2204B
|
|
|
|
|
Micro horn for smaller models. Glue into two punctures in control surface. Drilled for .032" (.8mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. Typical size for indoor pushrods all over the world. 2 per package. TEMPORARILY OUT OF STOCK SKU Number: MPJ2205B
|
|
|
|
|
Micro horn for smaller models. Glue into two punctures in control surface. Drilled for .039" (1mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. 2 per package. SKU Number: MPJ2206B
|
|
|
|
|
Small horn. Bolts on with provided fasteners. Drilled for .039" (1mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. 2 per package. TEMPORARILY OUT OF STOCK SKU Number: MPJ2210B
|
|
|
|
|
Small horn. Bolts on with provided fasteners. Drilled for .062" (1.6mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. This is the standard size for American (SAE) clevis ends. 2 per package. SKU Number: MPJ2212B
|
|
|
|
|
Small horn. Bolts on with provided fasteners. Drilled for .051" (1.3mm) Wire Z and L bends or other similar micro control rod ends. Can be drilled out to larger sizes if you wish. Next SAE Music wire size is .055". 2 per package. SKU Number: MPJ2211B
|
|
|
|
|
A molded plastic part with 8-32 threads. The intention is you can drill a servo arm, tap it for 8-32. Install and run two push-rods off the same pivot point on the servo arm. Use to drive mechanical retracts, brake, pick nose gear steering off the rudder servo. Take your pick. An old time part. We have a few packages in stock at the time of this listing. 3 parts per package. SKU Number: RCDHSS
|
|
|
|
|
Control horn in anodized aluminum. 30mm tall over all. Control radius, 18.5, 21.5 and 25.5mm plus distance from mounting surface to hinge axis. SKU Number: RRCC16130
|
|
|
|
|
Control horn in anodized aluminum. 20mm tall over all. Control radius, 14.5, 16.5 and 19.5mm plus distance from mounting surface to hinge axis. 6 horns per package. Color may vary from blue, red or purple, we'll ship what we have. SKU Number: RRCC16120
|
|
|
|
|
Control horn in anodized aluminum. 14mm tall over all. Control radius, 8.2, 10.2 and 12.2mm plus distance from mounting surface to hinge axis. 6 horns per package. SKU Number: RRCC16114
|
|
|
|
|
Slip over horn with adjustment wheel collar as shown in photo. This is a complete set of adjustable horns that slip over the wire. Your aileron pushrod connects to this part. Simplifies servo link hook-ups. Includes (2) 3-32 Dura-Collars, (2) Nylon Horn Connectors, and (2) 4-40 x 1/8 Slotted Screws. For .093 wire. (QTY/PKG: 2 ) Weight: 3 grams/set (1.5 grams/each). SKU Number: DUB103
|
|
|
|
|
Tired of your carbon bracing breaking out chunks of foam? These hard points are intended to go on the suface with the rod passing through the hole/slot and to spread the stress over a larger area. Less damage, more flying! The large double hole is for X landing gear to pass through. Precision made from 1/64th aircraft plywood, the quality you expect. Small slots/holes are for 1mm (.039) rod, larger slots/holes are for 1.5mm (.059) rod. Designed in conjunction with Scott Barnhart. SKU Number: RRCF3PHP
|
|
|
|
|
This system was designed for medium to large aircraft using 2-56 control rods and standard clevises. Bolt is 6-32 X 1 1/2" long. Adjustable horn is 3/4" long. .40 to .91 sized aircraft. Mounts in 9/64" drilled hole. SKU Number: DUB867
|
|
|
|
|
For large aircraft .91 and larger, comes complete with high quality aluminum horns, washers, steel 8-32 long shaft, nuts, horn arms, and clevises (for 4-40 rods) with aluminum pivot pins. 2/pkg.. SKU Number: DUB882
|
|
|
|
|
For medium to large scale aircraft .40-.91. Adjustable width to exactly match your rudder control horn width. Comes complete with high quality aluminum horns, washers, steel 6-32 long shaft, nuts, horn arms, and kwik-links (for 2-56 rods). 2/pkg. SKU Number: DUB880
|
|
|
|
|
Includes 4 each E/Z Adjust Nylon Horn Bracket only. These are interesting parts. Intended to be used on the threaded vertical leg of aileron torque rods. They allow you to adjust the control radius (adjust the horn up and down) by turning on the threads. You could also use one of these on a long bolt or set screw on a wheel collar to make a nose gear control or other specialty horn. 3/32" ID hole for 4-40 threads. (No, I don't know why Du-Bro calls this a "bracket".) SKU Number: DUB557
|
|
|
|
|
Includes 4 each E/Z Adjust Nylon Horn Bracket only. These are interesting parts. Intended to be used on the threaded vertical leg of aileron torque rods. They allow you to adjust the control radius (adjust the horn up and down) by turning on the threads. You could also use one of these on a long bolt or set screw on a wheel collar to make a nose gear control or other specialty horn. 1/8" ID hole for 6-32 threads. (No, I don't know why Du-Bro calls this a "bracket".) SKU Number: DUB559
|
|
|
|
|
Get rock solid control of your surfaces with these horns. Made to fit the precut Slow Stick holes exactly. No more wobbly bendy horns slopping up your flying performance. Ever wonder how much the in flight wind loads move them around? I say it does a lot and this is mostly because of the sloppy stock horns. Pick up a few MPH of wind and you can still fly with this mod. Also, she'll fly smoother when you actually get 100% of the throw you command. Solid control, that's where it's at! Horn set is two complete horns, glue into the foam tail parts with foam safe CA. The horn is made from 3 parts providing lots of support on the surface of the horn. There is no substitute for straight stiff control rods, make sure your control rod setup is right to get the very best from these horns. SKU Number: RRCSSCH
|
|
|
|
|
A split elevator torque rod with centrally molded on control horn. Horn is molded onto wire. Approx 4 1/16" (103mm) wide, Legs approx 1" (25.4mm) long. Horn is in center and drilled for control radius of .5" (12.7mm), .75" (19mm) and 1" (25.4mm) control radius. TEMPORARILY OUT OF STOCK SKU Number: SIGSH554
|
|
|