HS-65HB/MG / 5065MG / 70MG / 5070MH - Horn & Hardware Set Micro 25T. This is the replacement HS-65HB/MG servo horn set from Hitec. This set contains one star shaped horn (24mm), one short (25.4mm), and one long (35mm) servo arm. Set also includes mounting screw to mount servo horn to servo and lock washers.
Harrier Supreme V2 ESC's are made for a wide variety of applications. Comes with extensive manual for programming all settings. Well documented. Programming card compatible available seperately.
A123 Systems/LithiumWerks #18650 3.2 V 1.8 Ah 1800mAh Lithium Iron Phosphate (LiFePO4) Battery Single Cell.
[edits pending.....These batteries are capable of 30C constant discharge, with a 10 second pulse rating of 60C. Cycle up to 1000 times before significant capacity loss occurs. The rugged assembly of the products will ensure that your pack will last for years, not months. Can be repeatably charged to 100% in 15 minutes. This is the nano phosphate technology the automobile companies are testing on their future hybrid vehicles. Charge only with Lithium chargers with an A123/LithiumWerks mode limiting charge voltage to 3.6V per cell. ]
Specifications:
Manufacturers Part Number: 320749-001
Nominal Ratings:
Voltage 3.2 V
Capacity @ C/5 Typical (Min) 1.8 Ah (1.7)
Energy 5.76 Wh
Specific Energy 133 Wh/kg
Energy Density 330 Wh/L
Impedance (1kHz ACIR) < 20 mΩ
Cycle Life at 0.5C/0.5C, 100% DOD > 4000 cycles
Discharging:
Max Continuous Discharge Current 5.4 A (3C)
Max Pulse Discharge Current, 10s 18 A (10C)
Minimum Voltage 2.0 V
Temperature -20°C to 60ºC
Charging:
Recommended Charge Voltage 3.6 V
Recommended Charge Current <= 0.9 A (C/2)
Max Continuous Current,>10ºC2.7 A (1.5C)
Terminate Charge @ 3.6 V < 36 mA
Float Voltage 3.5 V
Temperature 0ºC to 60ºC
Storage:
Temperature -30 oC to 70 oC
Mechanical:
Diameter O18.5 +/- 0.1 mm
Length 64.95 +/- 0.2 mm
Mass 43.4 g +/- 1.0 g
Certifications:
Transportation shipped @ <= 30% SOC UN 3480, UN 38.3
Heavy Duty 14.5 gauge (1.810mm^2) 360 strand wire. Insulation diameter 3.2mm. Great for power supply extensions, charge cords and other high amperage applications suiting a high strand count quality vinyl jacketed wire. Select desired length below, cut in bulk.
Notes: 15 guage is 1.65mm^2, 14 guage is 2.08mm^2. Thus, this wire @ 1.81mm^2 is approximately 14.5ga.
Brushless 64mm brushless ducted fan. 4600KV motor with EP2540x6 blade rotor. Use optional heat sink GWACS019 for running over 11.1v input.
GWS Performance Chart
Volts
Amps
Thrust G/OZ
Watts Power
Efficiency Grams/Ounces Per Watt
7.4
9.5
212/7.48
70.30
3.02/106.36
11.1
17.2
410/14.46
190.92
2.15/75.74
12
25.1
651/22.96
301.2
2.61/76.23
* At 12V power is boosted but fatal damage can occur from overheating, great care must be taken. Heat sink GWACS019 should be used. SKU Number: GWEDF064D
5S K6 Series 3300. 65C (195 amps) Constant; 130C (390 amps) Burst. High discharge cells. Industry Standard XH balance plug. Weight: 435 grams. Measures: 139 x 45 x 34mm.
ULTRA-HIGH POWER LITHIUM-ION CELL, 2800mAh, Multi-Cell Pack
INR18650-P28A
Molicel has dedicated our product development in the path of ultra-high power cells with focus.
[EDITS PENDING: The launch of a new generation 18650 power cell, INR-18650-P28A, featuring 7% higher capacity however 22% lower DCR compared to P42A. Its consistent 45A discharging performance has now enhanced hugely with superior fast charge capability up to 3C charging rate.]
This is a starting point of low impedance version that shall be ideal for premium segment in EV, eVTOL, micro-mobility, home appliances and more applications.
Single Cell is in last photo.
Molicel Battery - Ultra-high Power Cell INR18650-P28A
Charge Current: Recommended: 2.8 A (1C); Maximum: 6.0 A (3C)
Discharge Current: Continuous (MAX): 35 A
Dimensions: Diameter: 18.6mm X Length: 65.2mm
Weight: 46g
Power Output: 184W (10s, SOC 90%); 168W (10s, SOC 50%)
Energy Density: 610 Wh/l; 240 Wh/kg
ABOUT ADVANCED R&D PRODUCTS & APPLICATIONS bolt Up to 120W Higher retention for discharge energy up to 120W continuously loop 500+ Cycles High rate 80% retention electrical_services Fast Charge 13.5A continues charge south_west Lowest DCIR Max internal resistance 13.8 mOhm trending_down Low Impedance Growth Over long cycle thermostat Thermal Controlling In cell thermal distribution optimized (3-4 ?C)
Choose your custom pack from the options below, if there's a plug and wire combination not listed, type in your request in the box provide below the options. Photos depict wire configuration options, want something different, type in your request in the box provided below the options.
Please indicate # Cells x # Cells and other notes in the "Battery Pack Shape Notes" box below, then in the Comments section at checkout tell us you're sending us a drawing, diagram, or photo.
Some helpful shape descriptions:
Square: # Cells High x # Cells High, Even # Cells, looks like two cells on top of two cells from end view.
Block: # Cells Flat Wide x # Cells Flat High
Block Offset/Nested: # Cells Flat Wide x # Cells Flat High Offset/Nested
Double Stick: # Cells End to End beside # Cells End to End, "Shotgun barrel style"
Triangle: 3 Cells in a triangle (1 cell nested on top of 2 cells)
Triple Stick Triangle: 2 Sticks of #Cells End to End + 1 Stick of # Cells High Nested, multiples of 3 Cells
Triple Stick Flat: 3 Sticks # Cells x # Cells Flat, multiples of 3 Cells
Quad Stick Offset/Nested: # Cells per Stick, 2 Sticks Wide x 2 Sticks High, Offset/Nested, Even Cell Counts
Capable of big sky flying or ball park low-n-slow! You can trust the Quick Wing in any flight condition. Any 20mm brushless motor system capable of turning a 4-6" prop at 50-150 watts or more will work well. She is sure to please the most speed hungry wing fanatic while still retaining very good slow speed handling characteristics. Quick "3D Jigsaw Puzzle" assembly in only 1-2 hours. World class laser cutting and design make this one of the quickest and most enjoyable balsa models you will ever build. You'll be amazed at the wide speed envelope the Quick Wing has. It easily goes from high speed to ball park flying with no bad habits. I'm totally comfortable recommending this kit as a good 2nd or 3rd model as long as you keep the power system modest. Advanced pilots can take the power as far as they like.
Specs: Wing Span 22.25" Wing Area 195 sq. in. Weight 8.5-14oz. Length 13.75" Average Cord 9.75"
Required: Covering;3ch+ Radio with elevon mixing; RX;2 Micro servos (HS-55 or similar); 50-200 watt 20mm motor; Prop; 700-1800mah+/- 2S-3S LiPB; ESC. If you select a receiver (RX), tell us which channel you need at checkout.
The HS-485HB updates the very popular HS-475HB by adding more torque and greater speed. With its top ball bearing, heavy duty, high impact Karbonite gears and high performance circuitry, the HS-485HB offers lots of torque and features excellent centering and resolution.
6S K6 Series 3800mAh 65C (247 Amps) Constant 130C (494 Amps) Burst. High discharge cells. Industry Standard XH balance plug. Weight: 640 grams. Measures: 44H x 48W x 140mm L. SKU Number: KYP6S3800HD65C
The new Sig Somethin' Extra has it all - good looks, incredible performance, Sig quality balsa and ply construction and every part in the kit is laser-cut!
This kit can literally be built as fast as the modeler can apply CA glue and accelerator. Fantastic flight performance using either 2-stroke or 4-stroke engines. The aerobatic capabilities of this model are virtually unlimited due to its thick airfoil section and very light wing loading. A perfect club contest airplane.
Kit Features: Balsa and Ply Construction, Pre-Cut Sheet Balsa Tail Surfaces, Durable Aluminum Main Landing Gear, Formed Tailwheel Wire, Molded Clear Plastic Canopy, Full Size Plans, Fast-Building 2 Piece Wing For Easy Transportation, Full Size Plans, Engine Mounts, Sig Easy Hinges, Pushrods, Complete Hardware Pack & Large Decal Sheet.
Wingspan: 51.5 in 1308 mm Wing Area: 614 sq in 39.6 sq dm Flying Weight: 4.25-4.75 lb 1928-2150 g Length: 48.25in 1226 mm Radio Required: 4 Channel, 4 Servos Recommended Engines: .40-.46 cubic in (6.6 - 7.5 cubic cm) 2-Stroke, .56-.65 cubic in (9.2 - 10.7 cubic cm) 4-Stroke
Special notes about electric from Dave: This model makes an excellent electric conversion. My first large electric was one of these on 20 1750FAUP Cells. Yikes, I'd love to do another one with modern packs! Here is how I'd do it. Yes, this is same chart as the 4 Star 40, similar weight and wing area. An under recognized yet excellent electric conversion model. Good weight to wing area. A little troublesome to get large NiMH packs into due to the wing tube. However, with Lipo's it's super easy to fit the pack. Below are my suggestions for a range of practical power systems.
Setup and Performance Chart
Motor
# Cells
Prop
Amps
Watts In
RPM
Thrust oz.
Pitch Speed MPH
Climb FPM
Est. Top Speed
Himax 3522-0990
3
12x6
41.7
469
8,470
62
48
1377
53
Himax 3528-800
3
12x10
37.4
421
6,950
66
54
1260
56
Himax 3528-800
4
11x7
36.6
549
9,770
65
68
1674
61
Himax 3528-1000
3
12x6
44.5
501
8,690
49
64
1490
54
Himax 3528-1000
4
11x5.5
51.4
771
11,660
61
85
2177
64
Himax 3528-1000
3
12x6
44.5
501
8,690
49
64
1490
54
Himax 5018-530
5
12x8
30.5
572
8,560
65
76
1839
63
Himax 5018-530
6
12x8
40.5
911
9,930
75
104
2766
73
Estimates based on manufacturers provided constants using E-Calc. High Quality 2100-3000mah used as trial cell in calculations. Presumed model weight of 76oz. @3 cells (added oz for higher cell counts). Actual performance may vary depending on components, accuracy of data provided by manufacturer, quality of battery, ESC, and many other factors.
Fits Himax 35 series outrunners and many others. Motor plate is drilled for 4 bolt pattern of 1" (25.4mm)diameter. This is a most common mounting pattern in motors of this class such as Himax 35XX Series and many others (does not fit AXI 28XX motors). Standoffs provided in 4 different lengths to aid your setup. Measurements provided so you can figure out spacing. Note, if motor is mounted inside front plate, it's thickness does not add to motor spacing off firewall. High impact plastic base plate supports ends of standoffs against firewall to a solid and rugged mounting system.
Fits motors with 1" (25.4mm) mounting spacing Max motor length- 53mm Max motor diameter- 35mm for Outrunners, 36mm for regular motors 4 sets of rods included lengths; 12.65" (32mm), 1.655" (42mm), 1.892" (48mm) & 2.125" (54mm) Font plate thickness: .117" (3mm) Rear plate mounting space: .140" (3.5mm) Weight- 1.6 to 1.8 oz. Includes all necessary hardware
Side By Side 9.6V FDK (formerly Sanyo) HR-AA NIMH Airtronics Stylus pack. HIGH capacity pack! Yes, it is the same size as your current AA pack. A "AA" is a "AA". This is what your computer TX should have come with! Tired of having to quick charge at the field? You can program all night friday night and fly all day saturday with a fully charged 1650. Also fits older Futaba gold case FG radios. In the Futaba case the pack appears to have 9 cells but one is a hollow dummy cell. This pack fits just fine and is correct voltage.
Maintenance charge and maximum form charge rate for this pack is not to exceed 100mah. See chart at top of category page for charging recommendations.
Form charge on factory wall charger only, not to exceed 100mah. Attempting to form charge (initial charge) on peak detection charger or by any other method not specifically stated here is not recommended and voids warranty.
These motors are for large models weighing 10-12Lb for 3-D flight, 17-22Lb for aerobatic flight and 22-30Lb for leisure flight. High torque to turn large props direct drive. Mounting hardware and connectors included. Himax Brushless motors are manufactured to high standards for the discerning modeler. Designed for light-weight, high efficiency, high torque and durability Himax Outrunner motors are sure to make today's radio controlled models perform.
All HC63 series outrunner motors include: Prop adapter, female wire connectors, motor mounting kit w/screws and two hex keys.
Specifications:
Weight
Size D x L
Amps
Shaft
Max Motor RPM
KV
Resistance
No Load Current
690g/24.3oz.
63mm(2.48") x 63mm(2.48")
30-80, 100 15s
8.0mm (.315")
10k
230
.025Rm
1.9A
Setup and Performance Chart
# Cells
Prop
Amps
Watts Input
RPM
Static Thrust oz.
Pitch Speed MPH
12
16x12
77.7
3636
8,550
349
97
12
18x8
81.1
3795
8,450
397
64
10
18x8
62.4
2434
7,390
295
56
10
16x12
59.6
2324
7,460
261
85
10
16x12
57.3
2625
7,630
276
87
10
15x10
43.2
1685
7,880
212
75
8
20x10
69.2
2159
5,650
279
54
8
20x12
77.5
2418
5,460
298
62
7
22x12
81.1
2214
4,620
286
53
Estimates based on manufacturers provided constants using E-Calc. Kokam 3200 used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables. SKU Number: MPIHC63320230
Thank you for purchasing this short kit by Stevens AeroModel. The Adrenaline Rush was designed to achieve optimum performance with an affordable GWS EDP-50XC or 12mm Brushless inrunner systems. This Mini Hotliner / Racer features a wide flight envelope with forgiving stall characteristics. The model will slow to a crawl yet climb out to a dot in seconds and reaches blistering speeds in a shallow dive.
This product is cut to order, please allow a possible 7-14 business days for production.
o Ideal club racing platform. o Cuts through high winds that sends all other pilots packing. o Durable solid balsa and carbon construction. o Simple one evening construction from building board to first flight. o Outstanding performance from simple brushed 180 motors.
General Information: Short Kit Contents: o Illustrated Instruction Manual o Laser Cut Wing, Blocks, and Tail Feathers. o 1 - 0.194" x 17" Carbon Fiber Fuselage. o 1 - 1/32" x 18" Pushrod Stock. o 1 - 1/32" x 12" ID Nylon Pushrod Guide tube. o 3 - Du-Bro Micro Control Horns o 3 - Du-Bro EZ-Links
Radio Setup: o 2 - 6g Sub Micro Servos (JR-SM8 or HS-50) o 1 - Micro receiver (Berg Micro Stamp MS4 or MS4L) o 1 - 12mm Heatsink (GW/EHS-50 - functions as motor mount)
Suggested Brushed Power System: (38 mph): o 1 - 12mm "IPS" Brushed Motor (GWS EDP-50XC) o 1 - 5A Brushed ESC (Castle Pixie 7P) o 1 - 300-450mAh battery. (E-TEC 300mAh 7.4v) o 1 - 3x2 GWS Direct Drive Propeller
Suggested Brushless Power System: (65-80+ mph): o 1 - 12mm Brushless Motor (Medusa MR-012-030-4000) o 1 - 9A Brushed ESC (Castle Thunderbird 9) o 1 - 300-450mAh battery. (E-TEC 450mAh 11.1v) o 1 - 3x2 or 3x3 GWS Direct Drive Propeller
Himax Brushless motors are manufactured to high standards for the discerning modler. Designed for light-weight, high efficiency and durability of todays performance. Select ESC Combo below.
Specifications/Constants:
Weight
OD x Lengths
Max Efficient
Shaft
Max Motor RPM
KV
Resistance
No Load Current
65g(2.3oz)
20mm (.79") x 42mm (1.68")
6-15A
2.0mm(.078")
60k
3200
.144Rm
.53A
Setup and Performance Chart
# Cells
Prop
Amps
Watts In
RPM
Thrust oz.
Pitch Speed MPH
2
4.7x4.2
10.5
79
18,150
10
69
2
5.5x4.5
15.2
114
15,540
14
63
2
6x4
16.9
127
14,590
16
53
3
4.7x4.1
10.3
77
18,260
11
67
3
5.5x4.5
15.2
114
15,540
14
63
Estimates based on manufacturers provided constants using E-Calc. High Quality 500mah used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables.
Himax 3528 series motors are most generally used in 34-90 oz models depending on application. Replaces AXI 28 series motors. Manufactured to high standards for the discerning modeler. Package includes collet type prop adapter, prop saver, bullet females for your ESC and fasteners.
Specifications:
Weight
Size D x L
Amps
Shaft
Max Motor RPM
KV
Resistance
No Load Current
197g/6.9oz.
35.2mm(1.39") x 54.2mm(2.13")
8-29, 40 15s
5.0mm (.1969")
20k
800
.031Rm
1.7A
Setup and Performance Chart
# Cells
Prop
Amps
Watts In
RPM
Thrust oz.
Pitch Speed MPH
3
10x10
22.4
234
7,130
33
66
3
11x10
26.5
296
6,660
41
62
3
12x8
28.3
316
6,500
49
48
3
13x10
37.4
417
5,720
54
53
3
14x7
36.2
404
5,820
57
38
3
14x10
42.5
474
5,280
60
49
3
15x10
47.4
529
4,860
64
45
4
10x10
30.9
460
8,750
49
81
4
11x10
37.8
562
8,050
60
75
4
12x8
40.1
597
7,810
71
58
4
12x10
44.5
662
7,360
71
68
4
13x6.5
42.1
626
7,610
79
45
4
14x7
49.5
737
6,850
86
44
5
9x4.5
35.9
673
15,740
81
64
5
10x6
30.4
565
11,280
70
62
5
11x7
40.8
759
10,050
84
65
6
10x6
38.2
853
12,710
90
70
6
11x7
44.3
989
11,890
102
60
Estimates based on manufacturers provided constants using E-Calc. High Quality 2200mah used as trial cell in calculations. Actual performance may vary depending on components used, accuracy of data as provided by manufacturer, quality of ESC, weather and many other variables. * Over reccomended maximum RPM. SKU Number: MPIHC35280800
12 pack #2 laser cut aircraft ply washers. 1/16" thick (Aproximately .063" or 1.5mm), OD .650", ID .089". Use in many applications such as wing hold down bolts where a softer washer is often desired. Use for shimming motor mounts, servos and anyplace fine thickness adjustment is needed. Work well with metal and plastic fasteners. SKU Number: RRC2FW116
 "RRC K6 Series 2600 11.1V 3S 65C")
 "MayTech 25 Amp Harrier Supreme ESC")
 "A123/LithiumWerks LiFe Nano Phosphate 1800mah Single #18650 Cell")
 "2-Pole Red/Black Battery Zip Cord 14.5GA")
 "EDF064 w/2028-3 Brushless Motor")
 "RRC K6 Series 3300 18.5V 5S 65C")
 "RRC Gold Bars 33x8mm, 6PK")
 "RRC K6 Series 4500 7.4V 2S 65C")
 "MOLICEL Ultra-High Power 2800mAh Multi-Cell Pack, #INR18650-P28A Air")
 "Radical RC Quick Wing 20mm")
 "Hitec HS-485HB Heavy Duty Deluxe Ball Bearing Servo")
 "RRC K6 Series 3800 22.2V 6S 65C")
 "Sig Somethin' Extra Kit")
 "Stand Off Motor Mount for 35mm Outrunners")
 "FDK/Sanyo 1650mah AA NiMH 9.6V 8-Cell Airtronics Stylus/ Futaba FG TX Pack")
 "Himax HC6332-230 Series Outrunner Motor")
 "RRC K6 Series 18.5V 5S 1300mAh 65C")
 "Adrenaline Rush Mini Pylon Racer by Stevens AeroModel")
 "Himax 2025 3200KV Brushless Direct Drive")
 "Himax HC3528 Outrunner 800 KV")
 "RRC K6 Series 3000 14.8V 4S 65C")
 "#2 x 1/16\" Ply Fender Washer 12-Pack")
 "60/40 Rosin Core Solder 1oz. Spool")
