|
|
7 way cord. Includes plugs compatible with BEC, Tamiya, Traxxas, EC3, Futaba & JR RX's*, plug with cap and extra set of insulated leads so you can customize with and 8th plug. *Fits TX's with Universal and Futaba J servo ends also. Won't fit inside charge jack type switches for JR/Airtronics/Hitec where charging is through a window in the switch face. Works will all JR/Airtronics/Hitec batteries directly and switches with charge pigtails (except antique old Airtronics and antique Futaba G) SKU Number: RRCCGCD7WAY
|
|
|
|
|
EC5 plug to 4mm Gold banana on charger end on 22-gauge Silicone Wire charge cord. About 16-18" long. SKU Number: RRCCGCDEC5GB
|
|
|
|
|
Multiplex 6-Pin Female Silicone Charge Cords. About 8-10" long. 4mm banana on charger end. SKU Number: RRCCGCDMPX6
|
|
|
|
|
XT60 plug on 14ga heavy duty silicone charge cord. 30cm/12" Length, with 4mm banana plugs to interface with charger. SKU Number: RRCCGCDXT60
|
|
|
|
|
XT90 plug on 12ga heavy duty charge cord. 30cm/12" Length, with 4mm banana plugs to interface with charger. SKU Number: RRCCGCDXT90
|
|
|
|
|
Connect 1,2,3 or 4 MCX (Bind and Fly) batteries in series for faster charging on a single port charger. To be used ONLY when charging in BALANCE MODE. SKU Number: RRCCGCDMCX1234
|
|
|
|
|
Connect 3 each 2S packs or 2 each 3S packs in series to charge as 6S assembly. To be used ONLY when charging in BALANCE MODE. The best way to charge packs that are being discharged in series. Balance harness from battery pack must be plugged into the balance connector immediately adjacent to the charge connector where your heavy wires are plugged in. SKU Number: RRCCGCDDN236
|
|
|
|
|
4 x XT60 plug to on heavy duty charge cord. 12-14" Length. Heavy duty wire with 4 mm banana plugs to interface with charger. SKU Number: RRCCGCD4XXT60
|
|
|
|
|
Anderson Power Pole / Sermos charger cord added to one of our heavy duty cords. Standard 4mm banana on charger end. SKU Number: RRCCGCDAPPSER
|
|
|
|
|
4x Anderson Power Pole / Sermos charger cord added to one of our heavy duty cords. Length 12-14". Standard 4mm banana on charger end. SKU Number: RRCCGCD4XAPP
|
|
|
|
|
Found on larger single cell models (generally 300mah and up). Use to build your own single or multi-charge cords for single cell Bind and Fly battery packs. 22 gauge wire (heavier than normal). This is the plug found on charge cords and ESC battery inputs. SKU Number: RRCRCPBNFLARGE
|
|
|
|
|
Genuine Deans Ultra plug added to one of our heavy duty silicone charge cords. 11-12" long with banana plugs for most common chargers. We use only Genuine W.S. Deans Plugs. Standard 4mm banana on charger end. SKU Number: RRCCGCDDEANSUSIL
|
|
|
|
|
Genuine Deans Ultra plug added to one of our vinyl heavy duty charge cords. About 20-24" long with standard banana plugs for most common chargers. We use only Genuine W.S. Deans Plugs. Standard 4mm banana on charger end. SKU Number: RRCCGCDDEANSU
|
|
|
|
|
As per photo with caps. 12-14" Length. Heavy duty wire with standard 4 mm banana plugs to interface with charger. SKU Number: RRCCGCD4XDS
|
|
|
|
|
Genuine Deans 2 pin mini polarized plug added to one of our 22 gauge charge cords. About 18" long with banana plugs for most common chargers. We use only Genuine W.S. Deans Plugs. SKU Number: RRCCGCDDEANS2PP
|
|
|
|
|
EC3 plug to one of our 22 gauge bland charge cords. About 18" long. Standard 4mm banana on charger end. SKU Number: RRCCGCDEC3
|
|
|
|
|
4 Way EC3 Charge Cord. 12-14" Length. 12-14" length. Heavy duty wire with standard 4 mm banana plugs to interface with charger. SKU Number: RRCCGCD4XEC3
|
|
|
|
|
EC5 plug to one of our 22 gauge blank charge cords. About 18" long. Standard 4mm banana on charger end. SKU Number: RRCCGCDEC5
|
|
|
|
|
4 X EC5 plug to one heavy duty charge cord. Approximately 12-14" long. Standard 4mm banana on charger end. SKU Number: RRCCGCD4XEC5
|
|
|
|
|
Red BEC/JST charge cord for the most common park flier battery packs. This is the same plug used on all the S-300 and smaller GWS birds. It's the only red plug with covered pins. About 24" long. Standard 4mm banana on charger end. SKU Number: RRCCGCDRXBEC
|
|
|
|
|
Tamiya Block female plug added to one of our blank heavy duty charge cords for you. About 24" long. Standard 4mm banana on charger end. SKU Number: RRCCGCDTAMFB
|
|
|
|
|
Use to build your own single or multi-charge cords for single cell Bind and Fly battery packs. 26 gauge wire (heavier than normal). SKU Number: RRCRCPBNF
|
|
|
|
|
This charge adapter cord lets you charge 3 MCPX connectored 1S battery packs as a 3S series pack. The cord must be used with a Balance charger AND it MUST be in balance mode. Just putting it in charge mode will damage the batteries. Be sure you advance your lipo menu to BALANCE. This way you get to charge 3 battery packs at one time on one port. The XH 3S balance connector plugs directly into your balance port or balance board. Use a Red JST charge cord to interface with the Red JST plug for the power input. Set your charger to 3S, your choice of charge rate (observe MFG reccomendations) in balance mode and your off to the races. With a 4 port charger, it's simple to get 12 battery packs charging at once. This harness has 3 inputs for the MCPX connector and can be purchased just to get these pigtails to remove for your own custom charge harness if you like. TEMPORARILY OUT OF STOCK SKU Number: RRCCGCD3SMCPX
|
|
|
|
|
Multi Charge Cord with one each, Kyosho/Tamiya/Amp connectors on one end and standard 4mm banana plugs on opposite. About 24" long.
SKU Number: RRCCGCDKYTMAMP
|
|
|
|
|
Kyosho Block MALE CLIP plug added to one of our heavy duty charge cords for you. About 24" long. Standard 4mm banana on charger end. SKU Number: RRCCGCDTAMMC
|
|
|
|
|
Kyosho/Tamiya Mini Male Clip Charge Cord on one end and banana plugs on opposite. About 24" long. Standard 4mm banana on charger end. SKU Number: RRCCGCDMINTAMM
|
|
|
|
|
Charge Cord female HPI with banana male plugs. Approximately 24". SKU Number: RRCCGCDHPI
|
|
|
|
|
This charge adapter cord lets you charge 1, 2, 3 or 4 MCX bind and fly 1S battery packs in series. No need to fill it up, you can charge any number up to 4 in one charge session. The cord must be used with a Balance charger AND it MUST be in balance mode. Just putting it in charge mode will damage the batteries. Be sure you advance your lipo menu to BALANCE. This way you get to charge 3 battery packs at one time on one port. The balance end fits all the chargers we sell (excepting FMA Cell Pro) plugging directly into your chargers balance board port or 6S XH port. Charge input leads are standard 4mm bullets like all your normal charge cords. This harness has 3 inputs for the Single cell connector and can be purchased just to get these pigtails to remove for your own custom charge harness if you like. SKU Number: RRCBNF14S
|
|
|
|
|
Also known as a Gold Stecker, cord fits Super Tigre and other battery packs using this plug. SKU Number: RRCCGCDST35
|
|
|