|
| |
Incredible power to weight ratio. 11.1V 2000mah pack. This pack requires a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method. Discontinued, non-warranty, limited quantity, while supplies last. NEW. REG. $67.00 SALE !!!
SKU Number: KOK3S2000HD15C
|
|
|
|
|
| |
Connector Housing 2.5mm 5POS; XHP-5; JST Part #1125486, PRICED EACH
SKU Number: RRCMH05JST
|
|
|
|
|
| |
FDK (formerly Sanyo) single cell Ultra high capacity AA battery. Weight 30.3g, 1.07oz. FDK/Sanyo AA HR6 size cell. Button end cell. Unlike Sanyo's other NiMH cells, these ultra high capacity AA cells should never be fast charged EVER. We recommend 70mah (or less) wall chargers (very slow overnight charging) only. Suggested maintenance charge rate 50-70mah. Manufacturer's listed internal resistance is 25m. Discontinued by FDK(Sanyo), see the new Twicell version While supplies last!
SKU Number: RRC01H2500AABE
|
|
|
|
|
| |
Use to mount your charge plug to side of fuse or other panel. Makes it possible to charge without removing wing. WHILE SUPPLIES LAST, DISCONTINUED BY ERNST
SKU Number: ERN152
|
|
|
|
|
| |
Oringinal Security Clip, fits old style Futaba plugs. 2 clips for locking together important connectors. Mechanically locks the Futaba plug with a "snap", one pair for battery and aileron plugs. WHILE SUPPLIES LAST, DISCONTINUED BY ERNST
SKU Number: ERN115
|
|
|
|
|
| |
Correct gear to adapt your 2mm shaft motor (like many 20mm inrunners) into our 3.8:1 planetary gearbox. Width .199" (5mm). 15 tooth. Modulus/pitch is unknown. It's finer than .6mod and coarser than .3mod. Might be an engliish gear? Proper sun gear for the RRC 3.8:1 planetary gearbox.
SKU Number: HES3.8-2MMPINON
|
|
|
|
|
| |
Connects 3S packs to balancer and charger using Kokam connectors. Can be cut in half to make your own pigtails. While supplies last...
SKU Number: RRC3SBAL12EXTKOK
|
|
|
|
|
| |
Connects 4S packs to balancer and charger using Kokam connectors. Can be cut in half to make your own pigtails. While supplies last...
SKU Number: RRC4SBAL12EXTKOK
|
|
|
|
|
| |
Connects 5S packs to balancer and charger using Kokam connectors. Can be cut in half to make your own pigtails. While supplies last...
SKU Number: RRC5SBAL12EXTKOK
|
|
|
|
|
| |
Connects 3S packs to balancer and charger using Radical RC connectors.
Note: Can be cut in half to make your own pigtails.
SKU Number: RRC3SBAL12EXTXH
|
|
|
|
|
| |
Replacement Metal 1st gear set for Hitec HS-7115TH Servo. Original factory parts.
SKU Number: HRC55344
|
|
|
|
|
| |
Use a 3mm shaft motor in new style EDF 50 housing (GWDFS050). Use this adapter to mate to the new style Rotors. While supplies last!
SKU Number: GWADP007
|
|
|
|
|
| |
Flair Products FL1021 Baronette Plans & Instructions set imported from Flair Products, England. Usually Special Order, only one set in stock as of November 2014. Plans are folded.
Only 1 set left in stock as of 2/1/2022, no longer in production.
Flair is no longer in the business of producing and or selling model airplanes and their parts. Any inventory we have left in stock is the last and sold as is new in package unless otherwise stated, no warranty, no return.
SKU Number: FL1021PLANS
|
|
|
|
|
| |
1 Blade Tip, 1 Point Tip. WHILE SUPPLIES LAST, DISCONTINUED BY MFR.
SKU Number: KS911
|
|
|
|
|
| |
Designed for use in aircraft, car, boat, & helicopter models. Unlike conventional servo arms, they are made of long fiber composites for added strength. Longer versions have increased throw allowing for greater movement in controls. 8 Horns tan in color. WHILE SUPPLIES LAST, DISCONTINUED BY DU-BRO
SKU Number: DUB856
|
|
|
|
|
| |
Set of replacement ball bearings. Eight each ID 3mm x OD 6mm x Width 2mm Ball Bearings DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1114
|
|
|
|
|
| |
Dromida Ominus FPV Motor Cover Set. This is actually the motor mount. Ominus FPV Parts are different from the standard Ominus. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1164
|
|
|
|
|
| |
Dromida Ominus Prop Set. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1156
|
|
|
|
|
| |
Dromida Ominus Prop Set. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1157
|
|
|
|
|
| |
Dromida Ominus Prop Set. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1155
|
|
|
|
|
| |
Dromida Ominus Prop Set. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1110
|
|
|
|
|
| |
Dromida Ominus Shaft Set. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1116
|
|
|
|
|
| |
Dromida Ominus Canopy for Green. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1100
|
|
|
|
|
| |
Dromida Ominus Frame. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1121
|
|
|
|
|
| |
Dromida Ominus Frame. DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE1120
|
|
|
|
|
| |
INCLUDES: RTF Vista UAV Quadcopter, Radio, LED Lights, extra set of Blades four AAA Batteries, LiPo Battery, USB Charger, Instruction. Manual and Screwdriver. QTY limited to available stock. SPECS: Diagonal: 9.8" (251mm)
Weight: 4.3oz (122g) DISCONTINUED, WHILE SUPPLIES LAST
SKU Number: DIDE03
|
|
|
|
|
| |
D47 & D47S hardware set. Includes 4 servo horns, 2 servo horn screws, 2 mounting screws and two side mount tabs. Note, Dymond also lists the yellow version of this kit (11323). They are exactly the same except for color. We only stock the Red version which fits both servos exactly the same. Both servos are same output spline, same case, same fasteners. WHILE SUPPLIES LAST
SKU Number: DYM11327
|
|
|
|
|
| |
Dymond Precision Micro Servo D 200 BB #12001.
Coreless Motor
Precision ball bearing
Dimensions 1.1 x0.5 x 1.0
Weight 0.5oz.
Torque (4.8V) 35 oz.in.
Transit Time (4.8V)0.14 sec./60?.
Comes with universal connector, 2 control arms & mounting screws.
SKU Number: DYM12001
|
|
|
|
|
| |
Du-Bro 3.5 Adjustable Outboard Motor Mount WHILE SUPPLIES LAST, DISCONTINUED BY DU-BRO one left
SKU Number: DUB3101
|
|
|
|
|
| |
Dubro #6 x 1" button head screw. Package Quantity 8. WHILE SUPPLIES LAST, DISCONTINUED BY DU-BRO
SKU Number: DUB532
|
|
|
|
|
| |
Dubro #8 x 1" button head screw. Package Quantity 8. WHILE SUPPLIES LAST, DISCONTINUED BY DU-BRO
SKU Number: DUB535
|
|
|
|
|
| |
Micro horn sets. Extra long length for big throws on 3D ships. Can be trimmed to shorter lengths easily. 4 long single horns, 2 long double horns. Maximum control radius about .950" (24mm). Single arms are 1.1" (28.9mm) over all length. Double arms are 2" (51mm) over all length. Photo is manufacturers sample. Actual color blue. Known compatibility: Bluebird 303 and MPI MX-30 servos WHILE SUPPLIES LAST, DISCONTINUED BY DU-BRO
SKU Number: DUB933
|
|
|
|
|
| |
Micro horn sets. Extra long length for big throws on 3D ships. Can be trimmed to shorter lengths easily. 4 long single horns, 2 long double horns. Maximum control radius about .950" (24mm). Single arms are 1.1" (28.9mm) over all length. Double arms are 2" (51mm) over all length. Photo is manufacturers sample. Actual color gray. Known compatibility: GWS Narrow/Pico/MPI MX50 WHILE SUPPLIES LAST, DISCONTINUED BY DU-BRO
SKU Number: DUB932
|
|
|
|
|
| |
Replace lost pins from Dubro 917 & 921 Micro Clevis. WHILE SUPPLIES LAST, DISCONTINUED BY DU-BRO
SKU Number: DUB918
|
|
|
|
|
| |
These props are from the GWS Direct Drive / Hyper Drive series and are good for Higher RPMs than the Gear drive props above. Blades are stiffer and some in between pitches are here. Feel free to run these on gear drive and lower RPM setups if you like and the prop suits your needs better. Shaft hole size ranges from 1mm press on (2.5"props) to 1.5mm press on (3" props) to 4mm (4" & 5") props. All larger props are 3mm bore. Note prop size examples:
5030=5.0"diameter x 3.0"pitch.
2508= 2.5"D x.08"P Hyper drive props on RH side of photo, select your size below. Photo is taken before gray and black props were made. 90% of our stock is black or gray.
7035 props SOLD OUT!!! 6030 PROPS SOLD OUT!!!
SKU Number: GWEPDD
|
|
|
|
|
| |
These EP props are for gear drive applications.
Bore is 3mm which fits all GWS IPS and EPS gear drives. Select your size below.
Note prop size examples:
8060=8.0"Dx6.0"p
1575= 15"Dx7.5"p Please note: Pics of ALL GWS props are here. EP's in center with round tips. Photo is taken before gray and black props were made. 90% of our stock is black or gray. Latest generation of props may not have hex hubs. Prop are driven by friction between washers and nuts, not by the hex of the nut.
SKU Number: GWEPGD
|
|
|
|
|
| |
These props/rotors/impellers are for EDF Ducted Fan applications. Select size below.
SKU Number: GWSFR
|
|
|
|
|
| |
GWS Black, HD 3 Blade prop. Conventional tractor rotation.
SKU Number: GWPRO008A3D
|
|
|
|
|
| |
GWS Black, HD 3 Blade prop. Conventional tractor rotation. Includes an assortment spru of centering rings.
Priced per each propeller.
SKU Number: GWPRO002A3D
|
|
|
|
|
| |
GWS Black, HD 3 Blade prop. counter rotating or reversed pitch for use as a pusher or as a counter-rotating tractor on a multi motor aircraft.
SKU Number: GWPRR008A3D
|
|
|
|
|
| |
GWS Black, HD 3 Blade prop. counter rotating or reversed pitch for use as a pusher or as a counter-rotating tractor on a multi motor aircraft. Includes an assortment spru of center rings.
Priced per each propeller.
SKU Number: GWPRR006A3D
|
|
|
|
|
| |
GWS Black, HD 3 Blade prop. counter rotating or reversed pitch for use as a pusher or as a counter-rotating tractor on a multi motor aircraft. Includes an assortment spru of center rings.
Priced per each propeller.
SKU Number: GWPRR002A3D
|
|
|
|
|
| |
GWS Black, HD 3 Blade prop. counter rotating or reversed pitch for use as a pusher or as a counter-rotating tractor on a multi motor aircraft. Includes an assortment spru of center rings.
Priced per each propeller.
SKU Number: GWPRR003A3D
|
|
|
|
|
| |
GWS Black, HD 3 Blade prop. counter rotating or reversed pitch for use as a pusher or as a counter-rotating tractor on a multi motor aircraft. Includes an assortment spru of center rings.
Priced per each propeller.
SKU Number: GWPRR005A3D
|
|
|
|
|
| |
Made with barrell connector ready to go for the GWS C3-LP Charger. Plug into your 110V wall outlet and then plug power cord into your charger. Now you can leave the battery behind. Also a usefull power supply for many other chargers intended to run on 12V. Understand a running car 12V system is often about 14.5V so most other chargers made for typical 12V inputs will accept 15V just fine.
SKU Number: GWCHG006
|
|
|
|
|
| |
Use to teach another to fly. This is the standard cord to use between two GWS brand transmitters. If your tired of "pass the radio" you've found the right part. Note, although these "look" like JR cords they do not interchange. JR cords are 2 pole (mono) and GWS cords are 3 pole (stereo)
SKU Number: GWTRAINERCORD
|
|
|
|
|
| |
15 AMP control with BEC. . More versitile, capable of flying anything S-400 and below and will handle most 480 setups as well. Note, this control is inexpensive and works well but is about 3x as big as a GFS 12 or Castle 20. Weight 17g, Size 27.5x19.5x6mm.GWS Products warranty info. LIMITED QUANTITIES, WHILE SUPPLIES LAST!
SKU Number: GWICS400J
|
|
|
|
|
| |
Futaba Servo Gear Set S3114, S3114M, S3154 FUTM3467 Last one left!
SKU Number: FUTM3467
|
|
|
|
|
| |
30 AMP control with BEC and Brake. More versitile, capable of flying anything S-600 and below that is 30 amps or less. Weight 20g, Size 37x23.5x7mm GWS Products warranty info. While supplies last
SKU Number: GWGS600
|
|
|
|
|
| |
Motor mount for 400 type motors.
Beam mount type.
SKU Number: GWEMM400A
|
|
|
|
 "Kokam Lithium Polymer 3S 2000mAh 15C")
 "Connector Housing 2.5mm 5POS; XHP-5; JST Part #1125486")
 "FDK/Sanyo 2500mAh Single Cell NIMH Button End AA Battery")
 "Ernst Original Security Clips fits old style Futaba plugs")
 "RRC Planetary Gearbox 2mm Press On Pinion")
 "Kokam 3S, 12\" Balance Extension")
 "Kokam 4S, 12\" Balance Extension")
 "Kokam 5S, 12\" Balance Extension")
 "Radical RC 3S, 12\" XH Extension")
 "Hitec HS-7115th Mk 1st Gear Set (3pcs) LAST SET LEFT!!!")
 "EDF 50 3mm Adapter")
 "Replacement Tips for K & S 910 60 Watt Soldering Iron")
 "Du-Bro Airtronics Super Strength Long Horn Set")
 "Dromida Ominus Ball Bearing Set")
 "Dromida Ominus FPV Motor Cover (Mount) Set")
 "Dromida Ominus Blue Black Prop Set")
 "Dromida Ominus Yellow Black Prop Set")
 "Dromida Ominus Red Black Prop Set")
 "Dromida Ominus Green Black Prop Set")
 "Shaft Set Ominus Quadcopter")
 "Dromida Ominus Green Canopy")
 "Dromida Ominus White Frame")
 "Dromida Ominus Green Frame")
 "Vista UAV Quadcopter")
 "Dymond D47S + D47 Hardware Set")
 "Dymond Precision Micro Servo D200 #12001")
 "3.5 Adjustable Outboard Motor Mount")
 "#6 x 1\" Button Head Sheet Metal Screw, Qty 8")
 "#8 x 1\" Button Head Sheet Metal Screw, Qty 8")
 "Du-Bro Micro Horn Long Set for Bluebird / MPI")
 "Du-Bro Micro Horn Long Set for GWS / MPI")
 "Micro Clevis Replacement Pins")
 "GWS Direct & Hyper Drive Props")
 "GWS Gear Drive EP Props")
 "GWS Ducted Fan Rotors")
 "GWS 3 Blade Prop HD 6 x 3 Tractor, Black")
 "GWS 3 Blade Prop HD 8 x 4 Tractor, Gray")
 "GWS 3 Blade Prop HD 6 x 3 COUNTER ROTATING, Black")
 "GWS 3 Blade Prop HD 7 x 3.5 COUNTER ROTATING , Black")
 "GWS 3 Blade Prop HD 8 x 4 COUNTER ROTATING, Black")
 "GWS 3 Blade Prop HD 9 x 5 COUNTER ROTATING, Black")
 "GWS 3 Blade Prop HD 10 x6 COUNTER ROTATING, Black")
 "GWS 15V DC power supply for C3-LP Charger")
 "GWS Compatible Trainer / Buddy Cord")
 "GWS ICS 400 15 amp control")
 "Futaba Servo Gear Set S3114 S3114M S3154 FUTM3467")
 "GWS GS 600 30 amp control With Brake")
 "GWS Motor Mount 400A for 400 Type Motors")