|
|
Page [ 1 | 2 | 3 | 4 | 5 | 6 ] |
| - Whats New >
Til It's Gone!
|
All close-out sales are AS-IS and final. Products on this page are discontinued or replaced with newer models or are items we no longer have room to inventory. All items are new old stock.
Pricing for most items on this page are less than 1/2 (some less than 1/3!) of original price. In fact, I just recently cut most items here in 1/2 from the previous discount price! Get a bargain for some necassary parts or experimental gear. When it's gone it's gone, not to return to this page. These items are occupying a couple of shelving units we need for other products. Help us de-clutter and free up some much needed space and we'll help you get a screaming good deal! | | | |
EPS-100 Power Sytems are all the same Speed 280 motor in many different ratios. Comes with sleek gearbox. Remember, the higher the ratio the greater the static thrust at a lower speed. Choose wisely. By purchasing a few different props you'll be able to make adjustments to static, inflight thrust and pitch speed of your power system and come up with the best combination of performance for your bird. 100C on super Discount, check deduction in drop down box. You get them $6 flat! SKU Number: GWEPS100A-B-C-D-S1-S2
|
|
|
| |
EPS-280 Power Sytems are all the same Speed 280 motor in many different ratios. Remember, the higher the ratio the greater the static thrust at a lower speed. Choose wisely. By purchasing a few different props you'll be able to make adjustments to static, inflight thrust and pitch speed of your power system and come up with the best combination of performance for your bird. SKU Number: GWEPS280A-B-C-D-E-F-S1-S2
|
|
|
| |
All of these power systems use the same motor at different gear ratios. GWS says not to load them over about 6 amps. However, I've had good luck loading them to near 8 amps. They come with a sleeker gearbox than the 370DX series and a different lower KV S-300 motor. The quality is high in these powerful motors. They perform best on 7 or 8 720 NiMh or RRC 2x1800 Polymer packs. Remember, the higher the ratio the greater the static thrust at a lower speed. Choose wisely. By purchasing a few different props you'll be able to make adjustments to static, inflight thrust and pitch speed of your power system and come up with the best combination of performance for your bird. SKU Number: GWEPS300A-B-C-D-S1-S2
|
|
|
| |
All of these power systems use the same motor at different gear ratios. GWS says not to load them over about 6 amps. However, I've had good luck loading them to near 8 amps. They come with a sleeker gearbox than the 370DX series and a different lower KV S-300 motor. The quality is high in these powerful motors. They perform best on 7 or 8 720 NiMh or RRC 2x1800 Polymer packs. Remember, the higher the ratio the greater the static thrust at a lower speed. Choose wisely. By purchasing a few different props you'll be able to make adjustments to static, inflight thrust and pitch speed of your power system and come up with the best combination of performance for your bird. SKU Number: GWEPS350CBB
|
|
|
| |
These power systems have the most efficiant speed 300 motors you can get. All of them use the same motor at different gear ratios. GWS says not to load them over about 6 amps. However, I've had good luck loading them to near 8 amps. For this you'll have to do your own experimenting. The quality is high in these powerful motors. They perform best on 7 or 8 720 NiMh or RRC 2x1800 Polymer packs. Remember, the higher the ratio the greater the static thrust at a lower speed. Choose wisely. By purchasing a few different props you'll be able to make adjustments to static, inflight thrust and pitch speed of your power system and come up with the best combination of performance for your bird. SKU Number: GWEPSDX-370A-B-C-D-E-F-G-H-S1-S2
|
|
|
| |
All of these power systems use the same motor at different gear ratios. GWS says not to load them over about 12 amps. These are 7.2 S-400 motors. Although GWS normally reccomends these for 2S or 7-8 Nimh Nicad cells. They work well at 3S (or 10 round cells) if you keep the amps to 12 or less. they are best utilized at 8-12 amps range. No prop amp load chart is available for these. SKU Number: GWEPS-400A Thru I
|
|
|
| |
Everything except the motor that you need for onboard electronics for your indoor or park electric flyer. The GW/CB278/F Flight Pack contains: Two servos PICOX2 (includes servo horns, mounting hardware), Receiver R4P (specify channel below), Electronic speed controler ICS100, 5amp, 7 cell battery pack 8.4V/600mAh NI-CD. For Futaba/Airtronics radios. GWS Products warranty info. SKU Number: GWSCB278F
|
|
|
| |
Replacement gearbox frame for GWS LPS drive systems. SKU Number: GWLPS5A
|
|
|
| |
Replacement gear case/motor mount and 4 screws for type A-F IPS dual motors. SKU Number: GWIPSD-5A
|
|
|
| |
Replacement gear case/motor mount for 280 Power Systems. SKU Number: GWEPS5AB
|
|
|
| |
Screws included with some GWS power systems inteneded for mounting gearbox to firewall. Many possible other uses such as servo mounting screws, you name it. Small, phillips drive. Possible other GWS uses. Flat end screw intended to thread into predrilled hole. This metric screw is slightly smaller than typical 2-56 servo screws, perfect if your looking to shave some grams. Length .350" (9mm), Clearance hole/OD .068" (1.74mm), ideal threading hole .055 (1.4-1.5mm) (#54 drill bit). 4 screws per package. SKU Number: GWSGBXS
|
|
|
| |
These fit any brand S-300 series brushed motor and get them mounted in GWS (and many other brands) gearbox's. We recently found our stash of these screws and offer them here. Phillips drive, very thin heads so as not to interfer with gear rotation. 4 each per package. SKU Number: GWSC003
|
|
|
| |
Ball bearing set for Any LPS Single systems. All GWS LPS systems have 2mm shaft. Price per bearing. SKU Number: GWLPS2A
|
|
|
| |
Ball bearing for Any EPS-400 systems. Any GWS system with a 4mm diameter shaft. Price per each bearing. SKU Number: GWEPS2A4C
|
|
|
| |
Fully Compatible with JR ABC&W Crystals as well as the Berg 5 DSP2 crystals. Interchange at will. Made for single conversion GWS full size receivers. SKU Number: GWSSC
|
|
|
| |
4x10" section of solderable Tin coated steel sheet measuring about .008" (0.20mm). Solid Tin is easy to form, bend, cut and shape. Also easy to solder. Great for making your own scale details, straps, fittings and etc... DISCONTINUED, WHILE SUPPLIES LAST SKU Number: KS254
|
|
|
| |
Fast heating. Long life, lightweight. 30 watt, 550 degree F. 110V. Includes iron holder. Perfect for many applications like building custom wiring harnesses and the occasional tool or home repair. Every well equipped work space needs a soldering iron. DISCONTINUED, WHILE SUPPLIES LAST SKU Number: KS300
|
|
|
| |
Handy tube cutter for your shop or field box. Cut tube 1/16" to 5/8" O.D. For cutting copper, aluminum, brass and thin wall tubing. DISCONTINUED, WHILE SUPPLIES LAST SKU Number: KS296
|
|
|
| |
Clear fuel line for both glow gas and smoke fluids from K & S. ID: 1/16" (1.58mm); OD: .125" (3.17mm). Sold by the foot. Perfect for 1/2A and other small barbs. Enter number of feet as your QTY. DISCONTINUED, WHILE SUPPLIES LAST SKU Number: KS410FT
|
|
|
| |
Clear fuel line for both glow gas and smoke fluids from K & S. ID: 3/32" .093" (2.38mm); OD: .190" (4.82mm). Sold by the foot. Perfect for 1/8" and 3mm barbs. Enter number of feet as your QTY. DISCONTINUED, WHILE SUPPLIES LAST SKU Number: KS411FT
|
|
|
| |
Clear fuel line for both glow gas and smoke fluids from K & S. ID: .118" (3mm); OD: .235" (5.97mm). Perfect for 5/32" or 4-5.5mm barbs. Sold by the foot. Enter number of feet as your QTY. DISCONTINUED, WHILE SUPPLIES LAST SKU Number: KS412FT
|
|
|
| |
K & S Die Handle works with common 13/16" OD dies. 4 locking thumb screws make it easy to use with both round or hex shaped threading dies. DISCONTINUED, WHILE SUPPLIES LAST SKU Number: KS420
|
|
|
| |
Flair factory Messerschmidt BF110 decal set. Self Adhesive. Apply over fuel proofed finish. Out of production, only one set left in stock as of 9/25/15!
Flair is no longer in the business of producing and or selling model airplanes and their parts. Any inventory we have left in stock is the last and sold as is new in package unless otherwise stated, no warranty, no return.
SKU Number: FL1255
|
|
|
| |
Flair factory ASK 8 decal sheet. One Sheet. Self Adhesive. Apply over fuel proofed finish. Out of production, only two left in stock!
Flair is no longer in the business of producing and or selling model airplanes and their parts. Any inventory we have left in stock is the last and sold as is new in package unless otherwise stated, no warranty, no return.
SKU Number: FL1254
|
|
|
| |
5 x 5 inch with 5mm through hole (It's actually 4.81mm so the press on spinner fits it tightly). Maxx Products prop. While supplies last... SKU Number: MPIEPP0550
|
|
|
| |
NiCad SCP1500 Sub C Single Cell, fits screw-apart glow starters. SKU Number: RRC01N1500SCP
|
|
|
| |
Fiberglass Cloth has found many valuable uses in the model field. It is excellent for reinforcing critical strength areas of a model airplane such as the firewall attachment, wing center section, and landing gear installation. Model boat builders also like it for covering the bottom of a wooden boat hull for extra strength and puncture resistance. Polyester Glass Resin or slow-drying Epoxy Glue should be used to saturate the Glass Cloth and adhere it to the model structure. Glass Cloth and resin can also be used to mold entire model parts, such as a whole airplane fuselage. Cowlings, wheel pants, and any other model parts that have a lot of compound curves are also especially suited to fiberglass construction. Fiberglass parts such as these will have an outstanding strength-to-weight ratio and excellent dimensional stability. Lastly, many modelers like to use the ultra-light weight Glass Cloth as a covering material for their entire model, especially when an epoxy or enamel paint is going to be used. It's super strong and goes around compound corners with ease. Like the name implies, Glass Cloth is made of actual glass! First, very fine filaments of pure glass are spun into yarn. This yarn is then woven into varying weights of cloth. Glass is one of the strongest textile fibers, having greater tensile strength than steel wire of the same diameter. We have Glass Cloth available in four different weights to suit all possible modeling applications. Chemically treated to enhance glue/resin adhesion. This is the finest grade Glass Cloth available, manufactured by the largest fiberglass producer in the U.S. DISCONTINUED BY SIG, WHILE SUPPLIES LAST... SKU Number: SIGGF002
|
|
|
| |
Fiberglass Cloth has found many valuable uses in the model field. It is excellent for reinforcing critical strength areas of a model airplane such as the firewall attachment, wing center section, and landing gear installation. Model boat builders also like it for covering the bottom of a wooden boat hull for extra strength and puncture resistance. Polyester Glass Resin or slow-drying Epoxy Glue should be used to saturate the Glass Cloth and adhere it to the model structure. Glass Cloth and resin can also be used to mold entire model parts, such as a whole airplane fuselage. Cowlings, wheel pants, and any other model parts that have a lot of compound curves are also especially suited to fiberglass construction. Fiberglass parts such as these will have an outstanding strength-to-weight ratio and excellent dimensional stability. Lastly, many modelers like to use the ultra-light weight Glass Cloth as a covering material for their entire model, especially when an epoxy or enamel paint is going to be used. It's super strong and goes around compound corners with ease. Like the name implies, Glass Cloth is made of actual glass! First, very fine filaments of pure glass are spun into yarn. This yarn is then woven into varying weights of cloth. Glass is one of the strongest textile fibers, having greater tensile strength than steel wire of the same diameter. We have Glass Cloth available in four different weights to suit all possible modeling applications. Chemically treated to enhance glue/resin adhesion. This is the finest grade Glass Cloth available, manufactured by the largest fiberglass producer in the U.S. DISCONTINUED BY SIG, WHILE SUPPLIES LAST... SKU Number: SIGGF006
|
|
|
| |
3-4" Y harness built in our shop with Genuine Deans Ultra Red connectors. 3 batteries in series into 1 ESC. 14 gauge heavy duty wire. Use to add the voltage of 3 matched capacity packs together for higher volgat use. For example, 2 each 3S 4800 packs and 1 each 2S 4800 pack will yeild an output of 8S @ 4800mah.We sell and use only Genuine W.S. Deans Plugs. Plug-Harnesses-Ys-Pigtails Category Link While Supplies Last! SKU Number: RRCYDEANS3BS1E
|
|
|
| |
3-4" Y harness built in our shop with Geniune Deans Ultra Red connectors. batteries into 2 parallel ESC's. 14 gauge heavy duty wire. Lets your double capacity, for example you can run two 11.1 (3S) 2100mah packs together so they function just like 1 3S 11.1volt 4200mah pack. Great way to economize smaller packs you already own into your new larger projects.We sell and use only Genuine W.S. Deans Plugs. Plug-Harnesses-Ys-Pigtails Category Link While Supplies Last! SKU Number: RRCYDEANS1B2PE
|
|
|
| |
Replacement pigtail for your Speed 480 set up. Heavy duty Genuine Deans Ultra Red female connector. Approximately 9" long. Plug-Harnesses-Ys-Pigtails Category Link
SKU Number: RRC2PPFDUS480
|
|
|
| |
Maxx Products Light Weight Motor Mount, large size. Fits most outrunners up 400 watt range like Himax 35 series and AXI 28 series. Fits most Inrunners 20-28mm od. Injection molded part. Stands motor out 3.8" (97mm). DISCONTINUED BY MANUFACTURER, WHILE SUPPLIES LAST SKU Number: MPIACC3958
|
|
|
| |
Micro Motor and ESC Set. Micro Outrunner Brushless 5A Micro ESC, Speed Control and Brushless Micro Outrunner 3.5g, 7.4V. Discontinued, while supplies last! SKU Number: RRCMICROPFS74
|
|
|
| |
Micro Outrunner Motor 4500KV for 7.4 volt operation. Use up to ~3-4oz models. Specifications: KV 4500 Voltage 7.4V No load current 0.5A No load RPM 33200 +/- 3% Max continuous current 2A Continuous RPM 21000+/- 3% Resistance 1.18ohm Dimensions 13 x 4.6mm Shaft Dia. 1.5mm Weight 3.5g Discontinued, while supplies last! SKU Number: HEMICRO74V
|
|
|
| |
The Dash One-Meter from Hobby People is the easy way to get flying in a hurry. It is completely ready to fly, and easy to quickly assemble. Great Performance! Dash 1-M's power system is "just right". The Li-Po battery provides more run time with less weight than a typical NiMH battery, thus providing longer run times and consistent power to the brushed motor. Dash 1-M climbs out with authority and makes high speed passes with great stability. The wing and tail are molded from foam with an outer skin, making them resistant to "hangar rash", and can be easily repaired with foam safe glue. Simply fun to fly, fast at full throttle, easy to fly at 1/2 throttle, and glides power-off giving it a wide speed envelope and fun flying characteristics. NEW IN BOX, SOMEWHAT SHELF WORN, LAST ONE LEFT, DISCONTINUED, SALE IS FINAL, AS-IS NON-WARRANTY Assembles in minutes! Amazing features: - 1-Piece undercambered wing
- Bolt-on tail section for quick assembly
- Easily dismantled for storage in the original box
- Includes: Folding Propeller & spare
- Includes: Proportional ESC for throttle
- Includes: Li-Po battery, 2S 1000mAh
- Includes: Li-Po balancing battery field charger (12V Input)
- Includes: Transmitter, 27mHz 4-Channel; 2-Stick; Radio
- Extras: Rubber band for the wing retainer (probably need replaced due to age), ribbon to check wind direction
Requirements: - Transmitter requires 8AA alkaline batteries (not included)
Specification:
Wing Span: 39.4in / 1m Wing Area: 175 sq. in. / 11.29 sq. dm. Length: 25in / 635mm Flying Weight: 13.75oz / 390g Wing Loading: Wing loading is 34.53g/sq.dm. / (11.3 oz/sq. ft.) Brushed Motor: 400 size Brushed ESC: 10amp Photo Credit & Review: Model Airplane News SKU Number: HP117215
|
|
|
| |
Light weight design made of high quality aluminum bar stock. Shiny finish. Comes with 4mm collet. Reverse Pitch Version. Fits 5/32"(4mm) shaft diameter. Weight: 1.07oz(30g) for Cobalt 05, 15, 20, brushless motors. ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished to a brushed metal finish. Notes on Ordering: 1. Find out the size of the prop nut you need. 2. If you need a different prop nut, you need to order it separately. 3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut. Shiny Finish styles are considered "while supplies last", new style is brushed aluminum. SKU Number: MPIPSR50R
|
|
|
| |
Light weight design made of high quality aluminum bar-stock. Polished to mirror finish. Comes with 2.3, 3.2 and 4mm collets. Fits 2.3mm, 1/8" (3.2mm), 5/32"(4mm) shaft diameter. Weight: .26oz(7g) for Cobalt 400, Speed 400 motors. ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished. Notes on Ordering: 1. Find out the size of the prop nut you need. 2. If you need a different prop nut, you need to order it separately. 3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut. Shiny Finish styles are considered "while supplies last", new style is brushed aluminum. SKU Number: MPIPS29
|
|
|
| |
Light weight design made of high quality aluminum bar stock. Polished to mirror finish. Comes with 3.2 (1/8"), 4mm, and 5mm collets. Fits 5/32"(4mm) shaft diameter. Weight: .40oz(11g) for Cobalt 05, 15, 20, brushless motors. ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished. Notes on Ordering: 1. Find out the size of the prop nut you need. 2. If you need a different prop nut, you need to order it separately. 3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut. Shiny Finish styles are considered "while supplies last", new style is brushed aluminum. SKU Number: MPIPS38
|
|
|
| |
Light weight design made of high quality aluminum bar stock. Polished to mirror finish. Comes with 3.2 (1/8"), 4mm, and 5mm collets. Reverse Pitch Version. Fits 1/8"(3.2mm), 5/32"(4mm), 5mm shaft diameter. Weight: .40oz(11g) for Cobalt 05, 15, 20, brushless motors. ProSpin spinners are made from high quality barstock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished. Notes on Ordering: 1. Find out the size of the prop nut you need. 2. If you need a different prop nut, you need to order it separately. 3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut. Shiny Finish styles are considered "while supplies last", new style is brushed aluminum. SKU Number: MPIPSR38R
|
|
|
| |
Light weight design made of high quality aluminum bar stock. Polished to mirror finish. Comes with 4 and 5mm collets. Fits 5/32"(4mm) shaft diameter. Weight: .85oz(24g) for Cobalt 05, 15, 20, brushless motors. ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished. Notes on Ordering: 1. Find out the size of the prop nut you need. 2. If you need a different prop nut, you need to order it separately. 3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut. Shiny Finish styles are considered "while supplies last", new style is brushed aluminum.TEMPORARILY OUT OF STOCK, MANUFACTURER BACKORDER SKU Number: MPIPS44
|
|
|
| |
Light weight design made of high quality aluminum bar stock. Polished to mirror finish. Comes with 4 and 5mm collets. Fits 5/32"(4mm) shaft diameter. Weight: 1.07oz(30g) for Cobalt 05, 15, 20, brushless motors. ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished. Notes on Ordering: 1. Find out the size of the prop nut you need. 2. If you need a different prop nut, you need to order it separately. 3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut. Shiny Finish styles are considered "while supplies last", new style is brushed aluminum. SKU Number: MPIPS50
|
|
|
| |
Cut for reverse (counter rotating or pusher) prop. Light weight design made of high quality aluminum bar stock. Polished to mirror finish. Comes with 2.3, 3.2 and 4mm collets. Fits 2.3mm, 1/8"(3.2mm), 5/32"(4mm) shaft diameter. Weight: .26oz(7g) for Cobalt 400, Speed 400 motors. ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished. Notes on Ordering: 1. Find out the size of the prop nut you need. 2. If you need a different prop nut, you need to order it separately. 3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut. Shiny Finish styles are considered "while supplies last", new style is brushed aluminum. SKU Number: MPIPSR29R
|
|
|
| |
The factory original fitting to insert in a Cox fuel can. Filters fuel and allows plug in of fuel line. Restore or repair your gear. In factory package. Also available: 6-Packs (individually packaged) at a discount, helpful if your building a vintage hobby shop display. Photo shows one of each color as an example only. This listing is for a quantity of one (1) or 6-Packs. Select color, if we have red left and you ask for it, we'll send it, if not you get clear. We reserve the right to send a mix of colors on 6-Packs, as per our inventory allows. CLOSEOUT DISCONTINUED INVENTORY, NEW IN PACKAGE, SOLD AS-IS, ALL SALES FINAL, NON-WARRANTY SKU Number: COX753-6
|
|
|
| |
Used on Cox Sky Cruiser EP Glider. Electric applications only. Only 3 left in stock, order today! CLOSEOUT DISCONTINUED INVENTORY, NEW, SOLD AS-IS, ALL SALES FINAL, NON-WARRANTY SKU Number: COXA5877
|
|
|
| |
This is the original Cox glow head clip with wires. Fits Cox .049 glow heads and others. These are difficult to find now and collectable. They are also very practical and useful! We have a limited supply on hand. Get one while they last! Priced each, in a plastic bubble pack on Cox display card. CLOSEOUT DISCONTINUED INVENTORY, NEW, SOLD AS-IS, ALL SALES FINAL, NON-WARRANTY SKU Number: COXGLOCLIP755-6
|
|
|
| |
Original equipment Thimble Drome Prop. CLOSEOUT DISCONTINUED INVENTORY, NEW, SOLD AS-IS, ALL SALES FINAL, NON-WARRANTY SKU Number: COX3125X25
|
|
|
| |
Original equipment Thimble Drome Prop. Used on all Cox .020 engines. CLOSEOUT DISCONTINUED INVENTORY, NEW, SOLD AS-IS, ALL SALES FINAL, NON-WARRANTY SKU Number: COX45X2000
|
|
|
| |
Original equipment Thimble Drome Prop. Used on all Cox .020 engines. This is the stiffer gray plastic. CLOSEOUT DISCONTINUED INVENTORY, NEW, SOLD AS-IS, ALL SALES FINAL, NON-WARRANTY SKU Number: COX45X20GR
|
|
|
| |
Original equipment Thimble Drome Prop. Gray Props are extra stiff. CLOSEOUT DISCONTINUED INVENTORY, NEW, SOLD AS-IS, ALL SALES FINAL, NON-WARRANTY SKU Number: COX5X300GR
|
|
|
| |
Available again, great for glow and electric power. CLOSEOUT DISCONTINUED INVENTORY, NEW, SOLD AS-IS, ALL SALES FINAL, NON-WARRANTY SKU Number: COX5X350LH
|
|
|
|
|
|