This fine tote was inspired by a customer at IRCHA wanting a field box that just held his fuel jug and tools, no power panel, no field battery. He didn't request any drawers but I couldn't help myself! You'll find 2 drawers for your goodies. Room to mount your fuel pump, carries anybody's 1 gallon jug or can. Tool stand has enough room for all your ball drivers, plier and hemostat slots abound. A little extra room in the corners of the jug area to stand up props, blades and etc..
Features 2 drawers., built in transmitter rack and glow plug caddy. Has a rugged 1" hardwood handle.
Kit is made from light weight plywood laser cut to exacting standards. Plenty of tabs assure easy alignment and enough glue surface never to fall apart unlike other less thought out field box kits. Ruggedly designed drawers have adequate clearance to slide smoothly even after application of paint or polyurethane. Many features never before available in any field box.
Specifications: Length: 15" Width: 7.25" Height: 16" Fuel Container Area 6.5" x 6.75" wide.
Weight: Only 2.5lbs Empty. (Weight after finish applied.)
Kit contains all wood, rubber feet, screws, hardwood handle and fuel jug. Approximate assembly time 1-2 hours. Stain or paint to taste.
This FDK (formerly Sanyo) AA 1650 Multiplex pack is the only way to go when replacing your weak factory pack. 7.2 volts and 6 cells just more bang. Comes without plug, reuse your old plug, direct solder or select optional Multiplex transmitter connector below. No thermal fuse in these packs.
Maintenance charge and maximum form charge rate for this pack is not to exceed 100mah. See chart at top of category page for charging recommendations.
Form charge on factory wall charger only, not to exceed 100mah. Attempting to form charge (initial charge) on peak detection charger or by any other method not specifically stated here is not recommended and voids warranty.
New in package or Used (no original package), Type 72-7 (CH16-60) or 72-9 (CH11-15), 72mHz Radio Control FUTABA Radio FM Dual Conversion Transmitter (TX) Crystal. Ideal for a spare or restoration project. Please cross-check the part # with your manuals and make sure this will work with your application before making your purchase. While supplies last, out of production non-warranty.
Choose your Channel preference below, USED or NEW preference option, and any alternate channels you will accept if we don't have your first choice, below in the box. Note:
The FrSky Multi Protocol Module is a 4-in-1 transmitter module that is compatible with FRSKY X-Lite. It combines four RF chips (CC2500, NRF24L01+, A7105, CYRF6936) into a single circuit board, enabling support for various remote control protocols such as Futabas S-FHSS, Walkera DEVO, Spektrum DSM2, DSMX, Flysky, Frsky, WLToys, Hubsan, Hisky, Esky, Assan, and others. This module offers flexibility in controlling your model, providing an exceptional experience with your preferred transmitter.
Moreover, this module works seamlessly with the Multi-module project on github and is based on an ARM microcontroller. All available protocols are included in serial mode, which utilizes a serial protocol to communicate with your transmitter without the need for any hardware modifications. However, it is recommended to update your transmitter's firmware to the latest version before selecting and binding the model protocol from the Model Settings menu. For telemetry-capable transmitters, the integration of telemetry is effortless with the transmitter firmware.
The FrSky Multi Protocol Module operates at a voltage range of 5-9V, with an operating current of <=180mA, and operates at a frequency of 2.4G ISM band. It has a high RF power of +22dBm and is equipped with an ARM CORTEX-M(128K ROM, 20K RAM) MCU. The module weighs 32g and comes with 1 MPM LITE TX Module in the package.
Hitec Focus Series transmitter, connects battery to the transmitter.
LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male, female and two wire battery male single end leads/pigtails are quantity of 5 for $8. If you need 4 or more leads, get your discount by entering the quantity of "5-pk" deals you want because your getting 5 connectors for the price of 4 at $8.00. Mix and match any way you choose
Use to teach fledgling RC pilots to fly. This is the standard trainer cord used with all Hitec buddy systems. Connects the instructer's transmitter to the student transmitter. If your tired of "pass the radio" you've found the right part. The sweetest sound ever heard by student RC pilots is "I've got it, relax!"
Direct from Hitec/RCD:
Important Information Regarding Trainer cord compatibility: To our valued customers, While Hitec radios are known to be trainer compatible with other Hitec and Futaba systems, Hitec has determined that the two-way Futaba cord is not 100% compatible with our systems and strongly suggests it not be used at any time. Our tests show that when the Futaba trainer cord is used with a Hitec radio the slave transmitter will emit an RF signal, thus creating a potentially dangerous interference situation, and in some cases will burn up components in the slave and or master radio. Hitec suggests that only the one-way Hitec trainer cord (#58310) be used with Hitec radio systems for training. Failing to do so will void the customers warranty and could create a potentially dangerous situation. Hitec apologizes for any inconvenience this may cause, but the safety of our customers is our utmost concern."
Correct plug for building your own customer charge and battery testing cords for the 4.8V JR DX8 transmitter. Presumably any subsequent JR 4.8V (4 cell) TX's will use this plug.
NOTE: Does not fit the Spektrum DX5e or DX6i. Use charge cord part number: RRCCGCDTXJR96 or connector part number: RRCTXPP2.1MJR
How it works: SwitchGlo Pro simply plugs into a receiver channel, then to your glow plug. You assign a transmitter toggle switch to this SwitchGlo channel, and toggle your glow on and off, at startup or in-flight.
You can program mix SwitchGlo just as you can program mix any servo on your craft, allowing you to utilize your glow in ways you never thought possible! Low Throttle glow activation is achieved by programming your TX to activate the SwitchGlo channel at any throttle position you desire. You can further enhance your Low Throttle mix by assigning a toggle switch to activate the mix, thereby forever preventing "Hot Starts"
Know when you glow! - SwitchGlo will beep the entire time your glow plug is glowing, providing invaluable reassurance you never thought you needed! SwitchGlo helps you diagnose starting problems; a single beep from SwitchGlo signals the glow/ground loop is open, most often indicating your glow plug is spent. This feature greatly reducing your troubleshooting efforts!
Technology: SwitchGlo Pro is an intelligent and highly efficient on-board glow driver. Its state-of-the-art voltage adaptive algorithm optimizes the power transferred from your battery pack to your glow plug providing the ideal glow. Outfitted with low power components, switched-mode voltage regulation and adjustable firmware, SwitchGlo is not your conventional on-board glow system.
Other on-board glow systems use linear regulators that waste power (up to 3 times as much) and operate at dangerously high temperatures. These linear glow drivers also suffer from low glow at lower pack voltages, while SwitchGlo gives a strong and consistent glow from 4V - 9V. Combining the benefits of switch-mode voltage regulation and the smallest footprints on the market, SwitchGlo Pro is the most advanced way to glow! SwitchGlo Pro draws an insignificant 0.4mAh per 1 second of glow time and will not noticeably drain your receiver battery. Total onboard weight is only 25 grams including the pig tail.
Easy to cut gator off and solder on any plug connector you like, see options in drop down menu. Check out "Glow & Fuel Power Everthing" sub category "Glow Plug Fittings" for varieties. At your Add any of them to your basket and include a note with order that you'd like it added to your SwitchGlo Pro along with wire length you'd like. We'll do the soldering no charge!
Specifications:
Dimensions: 1.587" x .720" x .590"
Receiver cable: 8"
Glow Plug Pigtail: 8"
Weight: 28 grams with pigtail
Input Voltage: 4V - 9V input
Output Power: 4.8W
Power Consumption:
0.44mah per second of glow time
2.2mah per 5 seconds glow (average start)
4.4mah per 10 second glow (auto shut-off)
33mah to start craft for a typical 15 flights per charge
Over 2300 average glows on a 5200mah battery (assumes no other battery draw)
Ace Transmitter Charge Connector for 9.6V Futaba Tx's. This is the plug that goes into your Futaba transmitter to charge the Tx batteries. The center port of the plug (short spade internal connector) is negative. These are also used as output plug on Ace chargers. SKU Number: RRCTXPP2.5MFJ
These crystals fit any Hitec FM Transmitters in the 72mhz band. These TX xtals typically have "HTF" or "TF" printed on a white or white with black cap. All channels listed, but does not guarantee availability.
Word to the wise: Not sold by Hitec, so very hard to get. Must part out radio systems to get them. Our experience is that changing a TX xtal in a Hitec TX is a BAD IDEA. It will work and you'll range check well, but you'll pick up side bands and become a source of interference to other pilots. Regarding our Crystal Exchanges, we won't accept anything for a Hitec FM TX xtal except a Hitec FM TX xtal. Set the right example here and treat your fellow modeler with respect, get the retune done.
The Optic 5, 5-channel sport radio is the perfect transmitter for beginner pilots. With its simple-to-use design and advanced 2.4GHz technology, this radio will have you flying a variety of models confidently and securely from a basic trainer to more advanced aerobatic-type aircraft. Available with our Minima 6T full-range, micro receiver, Hitec's Optic 5 is your affordable and straightforward radio solution!
Features: AFHSS 2.4GHz technology 1024 Resolution High Precision Quad Ball Bearing Gimbals Digital Trim with Beep Sound All Channel Servo Reversing 5th Channel AUX Switch for Retracts or Engine Cut Elevon Mixing (Ch. 1 & 2) V-Tail Mixing (Ch. 1 & 2) ATV (Ch. 1 & 2) Trainer Function (Student Only)
MFG Stock # 160240 Optic 5 2.4GHz Transmitter and Receiver Combo Includes Transmitter and Minima 6T Receiver. Dry system, transmitter requires 8AA Alkaline cells.
Need a BEC to drive a really large load? Useful for high servo counts or many digital servos on larger craft. Use as a power supply aboard your UAV to drive sensor, transmitters or whatever your client has you testing.
NOTE: CC BEC Pro should never be operated in series or parallel with another BEC or backup receiver pack connected to the RX/Servo side of the circuit.
Size: 1.69" (43mm) x 1.3" (33mm) Height: 0.94" (24mm) Weight: 1 oz* (29g*) Max Amps: 20 amps peak** Max Volts: 2s to 6s LiPo Cars: 6s (25v), Airplanes: 10s (40v), Helicopters (with brake disabled): 12s (50v) Adjustable Output Voltage :4.8V to 12.5V
*Weight without wires **Ratings are determined with a 5mph airflow on the BEC.
Advice from Dave on setting voltage: For simulating a typical 4.8V RX pack set voltage 5.1 to 5.4. For simulating a 6V pack, set voltage to 6.4 to 6.8. Battery packs are not any set voltage but work over a range of voltages. Think about what your trying to simulate. A 4.8v pack is empty at about 4.4v, full at about 6v. A 6v pack is empty at 5.5 and full at about 7.5. For heli's where the tail servo and gyro won't take 6v packs, what the MFG is saying is it won't take 7.5V. Setting heli voltage to even 5.8 or 5.9 is fine as it just looks like a 4.8V pack hot off the charger. For older 2.4GHZ systems (Anything not Hitec/Airtronics and pre 2011 gear) we reccomend setting voltage to 5.4-6V range MINIMUM.
Pigtail for TX battery pack with for JR (after 2001) and Spektrum. For new style 8103 transmitters and others. This matches any JR/Spektrum brand TX with a white plug on the TX battery.
The PERS is a very tiny receiver-actuated on/off switch. It plugs into one of your receiver channels and lets you turn a device on/off using a stick, switch, or knob on your transmitter. The PERS performs the operation equivalent to a servo moving a mechanical switch back and forth, but in a much smaller package, and with no moving parts! The PERS will operate with any receiver running on 2-6V and can switch on/off pretty much any device up to 3A of current. The PERS is perfect for lights, glow plug drivers, motors, smoke pumps, rocket igniters, solenoids, relays, and whatever else you can think up. Wired correctly, it could be used to trigger cameras or other electronic devices. The PERS weighs just 0.3g, not including the 6" output wires (if left full-length these wires weigh another 0.3g).
If you don't mind doing a bit of soldering, the PERS can be easily reversed and assigned a fail-safe setting. The PERS was designed to use the power from your receiver battery, but it can also be configured to use a separate battery, up to 20V. Take a look at the PERS instructions (link below) for reverse/fail-safe settings and wiring diagrams.
The PERS is available with 4 different types of servo connectors to accommodate the various micro receivers available today. Scroll down to view the different options and cart buttons. Packing Note: PERS's ordered in 1pc quantities will come in individual packages. 3 and 10pcs quantities may be supplied in one package with one set of instructions.
Choose your connector option:
PERS with standard Universal/JR servo connector
This model comes with a standard universal/JR servo lead which will plug into any brand receiver which uses standard servo connectors. The servo lead is 3" of 28AWG wire in Futaba colors, but with a universal connector.
PERS with 1.00mm servo connector for Spektrum AR6400 receivers
This model comes with a 1.00mm servo lead that will plug into the Spektrum AR6400 and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in JR colors. The PERS is ten times lighter than the AR6400 receiver so it won't noticably affect the weight of your model. In one of the images below you can see the PERS plugged into an AR6400 receiver controlling a high-brightness LED.
PERS with 1.25mm servo connector for Futaba R616FFM micro receivers
This model comes with a 1.25mm servo lead that will plug into the Futaba R616FFM receiver and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in Futaba colors. The PERS is 20 times lighter than the R616FFM receiver so it won't noticably affect the weight of your model.
PERS with 1.50mm servo connector for Spektrum AR6300 receivers
This model comes with a 1.50mm servo lead that will plug into the Spektrum AR6300 and any receiver with compatible connectors. The servo lead is 1" of 30AWG wire in JR colors. The PERS is six times lighter than the AR6300 receiver so it won't noticeably affect the weight of your model.
Specs:
Receiver Power: 2.0-6.0V
Receiver Current Draw: <1mA (LED off), 5mA (LED on)
Maximum Continous Switch Current: 3.0 amps
Maximum Momentary (<2s) Switch Current: 4.0 amps
Maximum Switch Voltage: 20.0V (see instructions for using a separate battery)
Circuit size not including wires: 7.7 x 6.2 x 3.4mm (0.30 x 0.24 x 0.13in)
Specs - Universal Connector
Weight without output wires: 0.85g (0.030oz)
Weight with 6" output wires: 1.14g (0.040oz)
Overall length with 6" output wires: 23.7cm (9.25in)
Receiver connection: Universal/JR 0.1" connector, 3" 28AWG Futaba color wire
Specs - All Other Connectors
Weight without output wires: 0.30g (0.011oz)
Weight with 6" output wires: 0.59g (0.021oz)
Overall length with 6" output wires: 18.0cm (7.0in)
The Talon 60 is well suited for SMALL SCALE OR AEROBATIC HELIS ranging from 360-450 size requiring up to 1400 watts on 6S. This ESC offers Castle's industry-leading helicopter functions, such as the remarkable direct entry governor mode. Simply type in the desired RPM using a Castle Link USB adapter (redeemable coupon enclosed with purchase) and the free Castle Link Programming Suite running on a Windows (TM) PC.
The compact layout and slim profile of the Talon 60 is also perfect for SCALE, SPORT and AEROBATIC PLANES in the .32 - .60 range requiring up to 1400 watts on 6S. Mounting the Talon 60 is simple and stress-free in any setup.
The Talon series ESCs are known for sporting heavy-duty BEC's designed for today's servos. The Talon 60 is no exception. With its 20 AMP PEAK POWER and 8 AMPS OF CONTINUOUS POWER, it will keep even the most draining servos at ease.
CASTLE-LINK(TM)
For nearly 20 years Castle engineers have been setting the bar for industry leading software functionality. The Castle Link Programming Suite is the ticket to creating the perfect setup. Gaining access to the host of tuning parameters, including free firmware updates and added feature sets, requires only the Castle Link USB adapter (redeemable coupon enclosed with purchase) and the free Castle Link software on your Windows (TM) PC. Users can then fine tune many variables to enhance their level of expertise.
Power System Alerts
The Talon ESCs are programmed to sound a number of tunes and codes using the motor as well as flashing LED patterns to alert users to certain conditions regarding their power system, such as over temperature, excessive load and locked head speed.
Telemetry Capable
Telemetry has the potential not only to improve the safety of our models by monitoring battery voltages, ESC temperature, and other critical parameters, but it also creates other opportunities to get even more fun out of flying because you've essentially reduced the risks of "unknown" inevitable crashes. Think of the benefits to be had from alarms that will sound to warn you when there's interference about or if your receiver battery is running unexpectedly low. Requires purchase of Castle Telemetry Link for S.BUS2 (Item # 010-0152-00) and compatible Futaba Radio or Castle Telemetry Link for X-BUS (Item# 010-0148-00) and a compatible Spektrum Radio.
The TALON 60 is PROUDLY DESIGNED, MANUFACTURED AND SUPPORTED IN OLATHE, KANSAS, and is backed by Castle Creations' 1-year warranty and unparalleled 'make-it-right' customer support.
Technical Specs
Input Voltage Range: MIN: 2S LiPo
MAX: 6S LiPo
Max Continuous Amperage at full throttle: 60 amps*
Max Voltage: 25.2V
BEC Voltage: User selectable choice of 6 or 8 volt output (default is 6V).
BEC Output: 20 amp peak** , 8 amp continuous
Size: Width: 1.19" (30.2mm)
Length: 2.56" (65mm)
Depth: 0.41" (10.6mm)
Weight : 2.05 oz. (57 g) with wires
1.09 oz. (g) without wires
Connectors: N/A
Items Needed for Operation: Battery and Motor connectors sold separately.
Tools needed for installation: Soldering iron for attaching High Current bullet connectors to ESC, motor, and battery. (Deans Ultra Plugs, EC5 or Castle Polarized 4mm or 6.5mm)
Application Guidelines: SMALL SCALE OR AEROBATIC HELIS ranging from 360-450 size requiring up to 1400 watts on 6S and SCALE, SPORT and AEROBATIC PLANES in the .32 -. 60 range requiring up to 1400 watts on 6S.
Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Castle Link adapter included in package) and freely downloadable Castle Link Windows software. (A small subset of the settings available through Castle Link Windows software can be accessed via manual programming through the transmitter stick.)
These crystals fit any Hitec FM Transmitters in the 75mhz band. These TX xtals typically have "HTF" or "TF" printed on a white or white with black tip tab.
Like our 4D tote above except wider with double the drawers and a skosh more room in the fuel compartment means you can run a 1/2 gallon jug or 1 gallon fuel can in this compact field box.
Features 8 drawers, assortment of dividers for the thinner drawers. Built in transmitter rack and glow plug caddy. Power panel opens up to access additional storage space. Loop-Key cutouts for retaining your 1/2 gallon fuel bottle or 1 gallon fuel can with rubber bands or Vecro strip. False floor lifts out easily for service and replacement of your 12v battery. Has a rugged hardwood handle and a premade internal pathway for fuel pump wires.
Nothing on the market today gives you as much tool space or as many drawers!
Kit is made from light weight plywood laser cut to exacting standards. Plenty of tabs assure easy alignment and enough glue surface never to fall apart unlike other less thought out field box kits. Ruggedly designed drawers have adequate clearance to slide smoothly even after application of paint or polyurethane. Many features never before available in any field box.
Specifications: Length: 20.3" Width: 7.25" Height: 14.1" Battery Compartment footprint: 6.75"x3.85"x4.2" high. Fuel Container Area 4.35" deep x 6.75" wide. Weight: Only 4.55lbs Empty. (Weight includes finish.)
Kit contains all wood, rubber feet, screws, hardwood handle. Aproximate assembly time 2-3 hours. Stain or paint to taste.
Sanyo N-700 AAC Direct fit replacement for most Transmitters requiring square packs.
Weight 180g/6.37oz.
Adaptable to replace clip packs from early JR and Futaba TX's.
Maintenance charge and maximum form charge rate for this pack is not to exceed 70mAh. See chart at top of category page for charging recommendations.
Form charge on factory wall charger only, not to exceed 70mAh. Attempting to form charge (initial charge) on peak detection charger or by any other method not specifically stated here is not recommended and voids warranty.
A very capable aerobat - perfect for Small Field Flying!'.
When we started out to design a smaller, quick-to-build, and inexpensive kit, we found that we had the perfect starting point--our Javelin. Its great flying characteristics have made it one of our best-selling kits.
So, we found that by shrinking the original Javelin, simplifying the construction, and lightening parts where possible, what we ended up with is a fantastic flying model -- the Dart!
It's another in our Schoolyard series - a kit you can easily frame up in just a weekend, and once completed, enjoy at a local schoolyard or park.
All of this comes in a great looking design that is remarkably easy to build, thanks to our innovative design techniques and precision laser cut parts.
Although it only weighs just over a pound, ready-to-fly, the Dart's construction gives it surprising rigidity to handle most anything you can throw at it. Loops, rolls, inverted flight, snaps, spins, hammerheads, Cuban-8's, split-S, and more.
And after you're done tearing up the skies, throttle down to easily cruise around the field. Then when the time's right, setup for a nice, controlled landing.
Program in a transmitter flaperon mix, put the aileron servos into separate channels, and then enjoy even slower flights, shorter takeoffs, and slower landings!
Because of the interlocking design and high quality laser cutting of the parts, the Dart is a quick build. Not only does it build quick, but it also builds straight and true as all of the parts were designed to align properly with a minimum of fuss and alignment tools.
The wing is removable, giving access to inside the cabin area. From there, you have easy access to install most any brand of radio and control linkages.
Up-front, we've designed in a large hatch that covers the spacious battery compartment. This area will easily handle up to 1000mAh 2-3s packs.
Specifications:
Wingspan: 30 inches
Wing Area: 165 sq inches
Length (airframe only): 24.5 inches
Weight: 7-8 oz. framed; 17-20 oz. (rtf)
Radio: 4 ch. (5 w/flaperons)
Four 20+ in./oz. servos (Mini servos - similar to HS-5065MG)
Power:
100+ watt electric motor, 20+ amp ESC, 2-3s LiPo
Features of the Dart
Perfect for Small Field Flying
A low parts count and small size make this kit quick to build and easy to fly at schoolyards, ballfields, and parks.
Premium USA Hardware
Included in each Old School Model Works kit is a premium hardware package. We only source our hardware from brand-name, USA manufacturers to guarantee the best quality.
Dual Ailerons
Mounted underwing, these two pre-cut aileron hatches make it easy to install the aileron servos.
WEB-LOCK Construction
There's nothing else like it. Build our wings, straight and true - with a minimum amount of fuss.
Main gear
Included are the pre-bent main gear legs.
Front Hatch
Held in with magnets, this extra large hatch gives you easy access to swap out the flight battery.
Included Motor Spacers
Included are additional spacers to help position your electric motor at just the right spot, regardless of brand.
Additional items needed to complete the Dart kit:
Propeller o Motor mount & mounting hardware
"Y" servo harness (for aileron if 4 channel) or two short servo extensions (if 5 channel w/flaperons)
Pushrods (two 5" for ailerons, two 14" for elevator & rudder)
Clevises for the pushrods
Two 1.5" - 2" diameter main wheels
Tailwheel
Covering - 1 roll (more, depending on color scheme)
This is transmitter battery lead/pigtail that will fit Airtronics, Vanguard and RD Series transmitters.
LOOKING FOR A DEAL? All Futaba, JR-Hitec, Airtronics(old) connectors, male or female and two or three wire single end leads/pigtails are quantity of 5 for $8, regularly $2 each. Select your quantity option below.
This plug fits several transmitter battery packs with odd plugs. If your Futaba or Hitec TX pack has a white plug, this pigtail will fit. Be sure to triple check polarity when building a charge cord.
The RX40V Vertical Pin RX is and axtremely small, lightweight, short-range receiver designed for indoor or limited range park flyer use. Cropping of image suggestes a super short antenna, actual length 7 3/16". This RX will function with all Airtronics 2.4 Aircraft Transmitters.
Notes from Dave: This and the other park flyer RX from Airtronics are both rated at 100 meters or 330 feet. In testing the 6 channel, I found the rating to conservative to the extreeme being able to maintain link nearly out of sight overhead. I have not tested this unit but the 6ch is certainly good over 1000 feet in the air. If your unsure if if your model needs a full range RX or not, we invite you to phone in and we'll give you our reccomendations. I'll post actual test results here when I've had a chance to fly one of these.
Specifications: Frequency: 2.4ghz FHSS-1 Norminal Input Voltage: 4.8-6.0V Range: Aprox 100m (330ft) Dimensions: 0.94 x .072 x 0.23in (24 x 18.4 x 5.9mm) Fail Safe Support: Yes (CH1 - CH4)
This is the plug that goes into your Futaba transmitter to charge the Tx batteries. The center port of the plug (short spade internal connector) is negative. These are also used as output plug on Ace and Alpha 4 chargers. Above listed at $1.25 each. Choose your 6-pack deal here! SKU Number: RRCTXPP2.5MFJPK
HPP-22 is the perfect companion for the latest generation of Hitec radios and receivers. With the HPP-22 and a Windows® based PC users can download the latest software from the web and setup their transmitter and receivers, save and load data or update their equipment to the latest firmware. With USB plug & play compatibility and an easy to use PC interface the HPP-22 is sure to become a must have for the Hitec user.
Capabilities: Firmware Upgrade Data Setting Data Save & Load to PC Data Reset Auto Version Check PC interface for Hitec 2.4GHz Telemetry Monitoring System (With optional Sensor Station & Sensors)
Current Applicable Models: Receivers: Freedom 9, Optima 7 & 9 Transmitters: Optic 6 Sport, Aurora 9 Transmitter Module: Spectra 2.4 AFHSS Module The HPP-22 requires an internet connection to download software and a USB Cable with mini-B connector for operation.
Web Address for sofware download is: https://www.hitecrcd.com/tester/hpp_22.html
 "Fuel & Tool Tote 2 Drawer")
 "FDK/Sanyo 1650 AA NiMH 7.2V 6-Cell Multiplex TX Pack")
 "FUTABA FM Dual Conversion TX Crystal 72mHz NEW or USED WHILE SUPPLIES LAST!")
 "FrSky MPM Lite IRX4 2.4Ghz 4-in-1 TX Module")
 "2-Pole/Wire Battery Single End Pigtail Male JR/Hitec/Airtronics Z(new) Style")
 "Hitec Trainer / Buddy Cord")
 "TX Charge Plug for JR DX8 4.8V TX")
 "SwitchGlo Pro")
 "Futaba 9.6V TX Charge & Ace/Alpha 4 2.5mm Male Futaba J Power Port Connector")
 "Hitec FM 72mHz TX Crystals, New or Used")
 "Optic 5 2.4ghz Radio System")
 "Castle Creations CC-BEC PRO Battery Eliminator Circuit")
 "2-Pole/Wire TX Battery Pigtail JR/Spektrum White")
 "Hansen Hobbies PERS V2- Pico Electronic Receiver & Accessory Switch")
 "Castle Creations Talon 60")
 "Hitec FM 75mHz TX Crystals")
 "Mini Glow Field Tote 8 Drawer")
 "Radical RC 700mAh AA NiCad 9.6V 8-Cell Square TX Pack")
 "GWS FM TX Crystals")
 "Old School Model Works Dart Kit")
 "2-Pole/Wire Battery Single End Pigtail/Conn. Male Airtronics ATX (Old) Style")
 "TX Battery Mating Plug from MPI")
 "Airtronics RX RX40V 4-Ch Micro 2.4GHz FHSS-1")
 "Futaba 9.6V TX Charge & Ace/Alpha 4 2.5mm Male Futaba J Power Port Connector 6-Pack")
 "Hitec HPP-22 Programmer")
