|
| |
Mercury M100XF is the result of nearly 2 years of lab work by Mercury Chemist. This work has resulted in a formulation that is among the fastest, strongest and highest quality ever available. M100XF is formulated with Mercury proprietary ingredients that make it a great choice for tough to bond substrates. M100XF is a 100 cps and sets in 5 to 15 seconds and has minimal gap filling qualities and excellent wetting out features.
APPLICATIONS: High performance bonding of close-fitting parts including: plastics, rubbers, metal, wood, leather, fabric and composites to themselves or in various combinations.
USEFUL HINTS/NOTES: Bond time is extremely fast, align parts prior to assembly. Discontinued, while supplies last, all sales final.
SKU Number: MER100XF1OZ
|
|
|
|
|
| |
M2.6 Set Screw for 64mm Impeller Hubs and other uses. Package contains 5 screws. DISCONTINUED, WHILE SUPPLIES LAST, CLOSEOUT, SALE IS FINAL
SKU Number: GWEDF64-3
|
|
|
|
|
| |
Connect 3 each 2S packs or 2 each 3S packs in series to charge as 6S assembly. To be used ONLY when charging in BALANCE MODE. The best way to charge packs that are being discharged in series. Balance harness from battery pack must be plugged into the balance connector immediately adjacent to the charge connector where your heavy wires are plugged in. CLOSEOUT: WHILE SUPPLIES LAST!
SKU Number: RRCCGCDDN236
|
|
|
|
|
| |
Replacement Aluminum Prop/drive shaft adapter for GWS 75mm fans with early style rotors (EDF75-7 & EDF75-8). Rotor presses directly onto adapters splined shaft. Not for new style rotors. (New style rotors, a screw is used for attachment and can be seen in center of rotor) This is the adapter only without sets crews or wrench. Fits 2.3mm shafts. DISCONTINUED, WHILE SUPPLIES LAST, CLOSEOUT, SALE IS FINAL
SKU Number: GWEDF75-4
|
|
|
|
|
| |
DESCRIPTION: Mercury M68DB is a debonder especially formulated for Mercury CA adhesives. It is a clear liquid with a relatively low evaporation rate that attacks and dissolves cured or uncured Instant Superglue (cyanoacrylate).
APPLICATIONS: Can be used to debond misaligned parts or clean up excess adhesive. It also is useful for removing spilled adhesives from work area. Debonds accidentally bonded skin.
USEFUL HINTS/NOTES: Mercury M68DB Debonder works best under repeated applications rather than one excessively large application. Apply debonder, allow it to dissolve hardened superglue and repeat as necessary. Use in an inconspicuous area for testing. May attack certain plastics and remove paint or varnish.Discontinued, while supplies last, all sales final.
SKU Number: MER68DB2OZDE
|
|
|
|
|
| |
New model replacement hub for EDF 75 to drive new fan rotors with D cut. Fits motors with 3mm shafts. Great for those of you putting brushless motors into the GWS 75mm ducted fan units. DISCONTINUED, WHILE SUPPLIES LAST, CLOSEOUT, SALE IS FINAL
SKU Number: GWADP004B
|
|
|
|
|
| |
New type upgraded for higher power systems. Requires D cut shaft adapters. DISCONTINUED, WHILE SUPPLIES LAST, CLOSEOUT, SALE IS FINAL
SKU Number: GWDFS009E
|
|
|
|
|
| |
.156 OD, .014 wall x 12" Length. 1 rod per item. WHILE SUPPLIES LAST...
SKU Number: KS8128
|
|
|
|
|
| |
A handy companion for your flight box. Ideal for putting a couple drops of fuel right where you want them. 2 oz. capacity.
SKU Number: SIGPB001
|
|
|
|
|
| |
High Quality 30 Minute Epoxy. Use epoxy where a strong non-brittle bond is required. Firewalls, landing gear blocks, wing hold down bolt blocks, fuel proofing and on sensitive materials like foam. 30 minute epoxy is best for quick repairs and new model construction where lots of working time is required. Also excellent for wetting out small fiber glass sections. Hint! Need your joint to cure a little faster? Take a covering heat shrink gun to the joint and warm it up. Be carefull, the heat will at first cause the epoxy to become thinner, it might run out of the joint and make a mess. Also, be warned! A little heat goes a long way and can cause your glue to dry faster than you had planned. You can also preheat the glue before applying to the parts or pre heat the parts. And, if your resin feels hardened inside the bottle, just warm it in the microwave for 10 seconds or so and you'll be good to go! WHILE SUPPLIES LAST! Learn about epoxy from an expert at RCModelReviews
SKU Number: PARB3004
|
|
|
|
|
| |
High Quality 30 Minute Epoxy. Use epoxy where a strong non-brittle bond is required. Firewalls, landing gear blocks, wing hold down bolt blocks, fuel proofing and on sensitive materials like foam. 30 minute epoxy is best for quick repairs and new model construction where lots of working time is required. Also excellent for wetting out small fiber glass sections.Hint! Need your joint to cure a little faster? Take a covering heat shrink gun to the joint and warm it up. Be carefull, the heat will at first cause the epoxy to become thinner, it might run out of the joint and make a mess. Also, be warned! A little heat goes a long way and can cause your glue to dry faster than you had planned. You can also preheat the glue before applying to the parts or pre heat the parts. And, if your resin feels hardened inside the bottle, just warm it in the microwave for 10 seconds or so and you'll be good to go! WHILE SUPPLIES LAST!
Learn about epoxy from an expert at RCModelReviews
SKU Number: PARB3008
|
|
|
|
|
| |
Maytech 2205S 2300 RC DC Brushless motor engine With CCW thread on Shaft for FPV BTF racing drone quadcopter. SOLD OUT
SKU Number: MTO2205S2300CCW
|
|
|
|
|
| |
Kokam, 8.4V 640 mah, 2 cells in series, new. Pack weighs 24g/0.9oz. This pack requires a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method.
Low on stock, call first please. Discontinued, non-warranty, while supplies last, all sales final.
SKU Number: KOK2S0640HD15C
|
|
|
|
|
| |
Connector Housing 2.5mm 2POS; XHP-2; JST Part #555485, PRICED EACH
SKU Number: RRCMH02JST
|
|
|
|
|
| |
Weld Bond is a non-toxic, fume free adhesive formulated for smooth and porous surfaces alike. Bonds almost anything to anything. Weld Bond is not flammable, non toxic, non staining and won't become brittle with age. It may be mixed with water to form a brushable sealer if so desired. Weld Bond is Foam Safe and works well with Depron, Poly-Styrene and other hobby foams. Joint remains slightly flexible which is desireable with Depron and other sheet foams. If your friends all think your models are bricks, this is the glue for you as it's also advertised as a great masonry adhesive. Many purposes, one adhesive. DISCONTINUED, WHILE SUPPLIES LAST SOLD OUT - 4oz SIZE;
SKU Number: RRCWELDBOND
|
|
|
|
|
| |
Connector Housing 2.5mm 8POS; XHP-8; JST Part #923773, PRICED EACH
SKU Number: RRCMH08JST
|
|
|
|
|
| |
With solderable nickel tabs. Super High discharge 20C. 32G/1.1oz. This cell is commonly used for S-300 and up applications. Run 2P and these make great S-400 and S-480 or any brushless to 30 amps intermittent. Lithium packs/cells require a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method. Priced below in various configurations. NEW Discontinued, non-warranty, while supplies last, all sales final.
SKU Number: KOK1S0740HD20C
|
|
|
|
|
| |
NEW, *PARTIAL KIT IS MISSING PART(S) (WE DON'T KNOW WHAT IS MISSING) SOLD AS IS/NON-WARRANTY Slow Stick X - X-Trainer Repair Kits (WOOD ONLY) Includes laser-cut balsa and ply to build either SSX or X-Trainer Wing. These repair kits are of the new design. Hardware and instructions which are included in "Short Kit" are not included in this repair kit. This item is the Wing kit only, PARTIAL, MISSING PARTS(S). Instruction Download. SOLD OUT, NO LONGER IN PRODUCTION, NON-WARRANTY, SOLD AS IS.
SKU Number: MRCSSXXTRK-W
|
|
|
|
|
| |
Millennium R/C's X-Gear replacement carbon rod set. WHILE SUPPLIES LAST!
SKU Number: MRCXGC
|
|
|
|
|
| |
This item includes:
1. New improved battery mount
2. Improved front and rear wing mounts, stronger and better support for rubber bands pegs
3. Customizable servo mounts
4. Adjustable pushrod guide
5. Steerable Nose/Tail Gear Kit
6. Fuselage joiner
7. Velcro Strap and double-sided foam tape
8. Necessary screws, nuts and washer Normally stocked in assorted colors. If you have preference, list first and second choice. Wire size is .062 (1/16"), puchasing an extra set of wheel collars is suggested. WHILE SUPPLIES LAST, COLOR AVAILABILITY NOT GUARANTEED
SKU Number: MRCXFS*TG
|
|
|
|
|
| |
All purpose 5-minute epoxy in resealable .84 fl. oz. applicator. High strength bond, 1,500 psi. Sets up in 5 minutes and dries clear, resistant to most chemicals. All purpose bonding and repairs. Works best on metals, wood, concrete, ceramic, glass and china. - Clear
- 5 minute Handling time
- 8-10 minute Set time
- 1 hour Cure time
- Tensile strength: 1500 PSI
Easy flow syringe with snap open cap. Reseals for storage.
SKU Number: DVCN20845
|
|
|
|
|
| |
A classic dawn of aviation home built design. Simple under cambered sheet wing and open bottom fuselage construction, for 3-Channel control (RET).
Specifications: - Wingspan | 22 in.
- Wing Area | 100 sq. in.
- Length | 14 in.
- Flying Weight | 2.75 oz.
The 1919 White Monoplane Laser-cut Kit is a simple 1:12 scale model of a dawn of aviation home built design. This simple and quick building 3-Channel model, features a single surface under cambered wing design and open-bottom fuselage. This model is suitable for flying at larger indoor venues and outdoors in calm conditions. Includes: Laser-cut balsa and hardwood components and hardware package. Requires: - Basic building tools, covering film and adhesives (CA glue suggested).
- Requires Radio | 3-Channel (RET)
- Motor | GWS-LPS-B2C brushed motor and gearbox (no longer available)
- Propeller | 7x6 SF ESC |
- 2-5A Brushed Servos |
- Two Required - 3.7g Micro Battery | 250mAh 7.4V
Retired Design
This product was retired from our current catalog, as the motor and gearbox have been discontinued by the vendor. Product is still available to purchase as a special cut-to-order item - builder is advised that they will need to modify the design to fit modern power system offerings. *Allow 10+ days for production.
SKU Number: SAK-1919WHITE
|
|
|
|
|
| |
GWS Black, HD 3 Blade prop. Conventional tractor rotation.
SKU Number: GWPRO008A3D
|
|
|
|
|
| |
Tidy up and protect your servo wire. 3mm fits 1 servo cable. Works like Chinese finger cuffs, push ends toward center of piece to open up to insert wiring. Very nice for heli applications, keeps wires from straying and protects from friction damage. 3-foot packs available in Orange & Yellow. See other listings for color and size options. Limited supply available while supplies last...
SKU Number: RRCML03O
|
|
|
|
|
| |
The ParkBEC 6V is the 6 volt output version of our ParkBEC, the smallest and lightest switch-mode BEC on the market. The 6 volt output will give you more servo speed and torque than standard 5V models. It can support as many as six sub-micro servos.
ParkBEC 6V is especially well suited for small helicopters and 3d planes, where extra response speed or torque are needed.
It weighs only 6.5g and is designed for running parkflyer type aircraft with pack voltages up to 33.6V.
The ParkBEC 6V installs between your ESC and receiver. You don't have to modify your speed control to disable its internal BEC, just plug the ESC into the ParkBEC 6V. It uses a switching type power supply to efficiently convert high pack voltages into a steady 6 volts.
Additional notes
If you are using small servos make sure they can run at 6v. Some sub-micros, notably the Hitec HS-50 and Futaba S3154, can be damaged by a 6v supply.
For best results, ensure that the ParkBEC 6V is installed at least 2 inches away from your receiver and antenna.
ParkBEC 6V is not compatible with 2s lithium packs.
ParkBEC 6V cannot power multiple digital servos.
Product Specs
Model: ParkBEC 6V
Specifications:
Input voltage: 8V to 33.6v (3s-8s lithium, up to 21 NiMHs)
Output current: 1.25A continuous, 1.5A 60 second peak. (6 4-9g servos, 4 standard servos)
Weight: 6.5g/.23oz
Weight Without Wires: 4.4g/.16oz
6 Volt output
Universal connector fits all receivers
1.3V dropout voltage at 1A
Can be put in parallel
Applications:
Parkflyers
Small 3d aircraft
Micro helicopters
Robots
Discontinued by Manufacturer, while supplies last! Also see SportBEC
SKU Number: DEPARKBEC6V
|
|
|
|
 "Mercury M100XF High Performance ARF CA 1 OZ")
 "GWS M2.6 Set Screw for Impeller Hub (GWADP003)")
 "Charge Cord Board 3x2S or 2x3S into 6S")
 "GWS Fan Impeller Hub Set Early EDF75 to 2.3mm")
 "Mercury M68 Debonder 2 OZ")
 "GWS Fan Impeller Hub Set EDF75 D-Cut to 3mm Motor")
 "SIG PRIMER BOTTLE 2 OZ")
 "PARBOND 30 Minute 4 ounce Epoxy")
 "PARBOND 30 Minute 8 ounce Epoxy")
 "Maytech 2205S 2300kv Brushless Motor CCW")
 "Kokam Lithium Polymer 2S 640 mAh 15C")
 "Connector Housing 2.5mm 2POS; XHP-2; JST Part #555485")
 "Weld Bond -FOAM SAFE-")
 "Connector Housing 2.5mm 85POS; XHP-8; JST Part #923773")
 "Kokam 1S 740 mAh Single Cell raw Super High Discharge 20C")
 "Partial* Slow Stick X / X Trainer Wing Repair Kit, *missing part(s) - SOLD AS IS*")
 "Millennium X-Gear Replacement Rod Set")
 "Millennium RC X-Fuse Set w/Tail Gear")
 "Devcon 5-Minute Epoxy in Applicator, .84 FL Ounce")
 "1919 White Monoplane Laser-cut Kit by Stevens AeroModel")
 "GWS 3-Blade Prop HD 6 x 3 Tractor, Black")
 "Mesh Looming Wire Guard 3mm Orange")
 "Dimension Engineering ParkBEC 6V ~WHILE SUPPLIES LAST!")
