The full-size Monocoupe was always known for its exceptional flight performance. Tom Stark's model of this classic lightplane has proved to be a winner from its first test flight. Now you can duplicate this little beauty for your own enjoyment. 1973 Nationals Winner.
Includes Sig contest rubber, die cut balsa parts, covering material, wheels, prop, instructions, plans with isometric views and full set of decals.
Wingspan: 24" Lenght: 16"
Potential for electric conversion with today's modern micro gear.
These crystals fit any Hitec FM Transmitters in the 72mhz band. These TX xtals typically have "HTF" or "TF" printed on a white or white with black cap. All channels listed, but does not guarantee availability.
Word to the wise: Not sold by Hitec, so very hard to get. Must part out radio systems to get them. Our experience is that changing a TX xtal in a Hitec TX is a BAD IDEA. It will work and you'll range check well, but you'll pick up side bands and become a source of interference to other pilots. Regarding our Crystal Exchanges, we won't accept anything for a Hitec FM TX xtal except a Hitec FM TX xtal. Set the right example here and treat your fellow modeler with respect, get the retune done.
5" Super sharp stainless steel scissors. Sharp and long lasting. Perfect for trimming canopies, cutting trim and covering. No tool kit is complete without a quality set of sheers.
Incredible power to weight ratio. 11.1V 2000mah pack. This pack requires a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method. Discontinued, non-warranty, limited quantity, while supplies last. NEW. REG. $67.00
Use for it's heat sink feature, also adapts 20mm motors into 300 brushed motor fan housings such as the stock EDF-55 and EDF-64 housings or any other housing intended for a S300 sized brushed motor.
DISCONTINUED, WHILE SUPPLIES LAST, CLOSEOUT, SALE IS FINAL
The RXC version of this motor system has the 7.2V motor and is intended for use with 6-8 cell NiMH, NiCad or 2 Cell Lipo battery packs. Follow GWS prop selection recommendations to keep amps at 2 or less for best life out of these systems. This is the same motor as the famous IPS drive just in a lighter weight gearbox. We suggest you order an extra shaft or two in our GWS motor system parts section as the 2mm shaft can be bent in a crash easily. GW/LPS-RXC, 7.2V A Sa:M0.3 x 48T A:M0.3 x 12T 48T/12T= 4.0:1
The RXC version of this motor system has the 7.2V motor and is intended for use with 6-8 cell NiMH, NiCad or 2 Cell Lipo battery packs. Follow GWS prop selection recommendations to keep amps at 2 or less for best life out of these systems. This is the same motor as the famous IPS drive just in a lighter weight gearbox. We suggest you order an extra shaft or two in our GWS motor system parts section as the 2mm shaft can be bent in a crash easily. GW/LPS-RXC, 7.2V B Sb:M0.3 x 50T B:M0.3 x 10T 50T/10T= 5.0:1 IPS Dual Power System Data Tables
The RXC version of this motor system has the 7.2V motor and is intended for use with 6-8 cell NiMH, NiCad or 2 Cell Lipo battery packs. Follow GWS prop selection recommendations to keep amps at 2 or less for best life out of these systems. This is the same motor as the famous IPS drive just in a lighter weight gearbox. We suggest you order an extra shaft or two in our GWS motor system parts section as the 2mm shaft can be bent in a crash easily. GW/LPS-RXC, 7.2V C Sc:M0.25 x 62T C:M0.25 x 10T 62T/10T= 6.2:1
The RXC version of this motor system has the 7.2V motor and is intended for use with 6-8 cell NiMH, NiCad or 2 Cell Lipo battery packs. Follow GWS prop selection recommendations to keep amps at 2 or less for best life out of these systems. This is the same motor as the famous IPS drive just in a lighter weight gearbox. We suggest you order an extra shaft or two in our GWS motor system parts section as the 2mm shaft can be bent in a crash easily. GW/LPS-RXC, 7.2V D M0.3 x 87T M0.3 x 9T 87T / 9 T = 9.7
The RXC version of this motor system has the 7.2V motor and is intended for use with 6-8 cell NiMH, NiCad or 2 Cell Lipo battery packs. Follow GWS prop selection recommendations to keep amps at 2 or less for best life out of these systems. This is the same motor as the famous IPS drive just in a lighter weight gearbox. We suggest you order an extra shaft or two in our GWS motor system parts section as the 2mm shaft can be bent in a crash easily. GW/LPS-RXC, 7.2V E M0.3 x107T M0.3 x 10T 107T /10T = 10.7
The RXC version of this motor system has the 7.2V motor and is intended for use with 6-8 cell NiMH, NiCad or 2 Cell Lipo battery packs. Follow GWS prop selection recommendations to keep amps at 2 or less for best life out of these systems. This is the same motor as the famous IPS drive just in a lighter weight gearbox. We suggest you order an extra shaft or two in our GWS motor system parts section as the 2mm shaft can be bent in a crash easily. GW/LPS-RXC, 7.2V F M0.3 x106T M0.3 x 9T 106T / 9T = 11.8
Fast heating. Long life, lightweight. 30 watt, 550 degree F. 110V. Includes iron holder. Perfect for many applications like building custom wiring harnesses and the occasional tool or home repair. Every well equipped work space needs a soldering iron.
ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished.
Notes on Ordering:
1. Find out the size of the prop nut you need.
2. If you need a different prop nut, you need to order it separately.
3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut.
Shiny Finish styles are considered "WHILE SUPPLIES LAST", new style is brushed aluminum.
Light weight design made of high quality aluminum bar stock. Polished to mirror finish. Comes with 3.2 (1/8"), 4mm, and 5mm collets. Reverse Pitch Version.
ProSpin spinners are made from high quality barstock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished.
Notes on Ordering:
1. Find out the size of the prop nut you need.
2. If you need a different prop nut, you need to order it separately.
3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut.
Shiny Finish styles are considered "WHILE SUPPLIUES LAST", new style is brushed aluminum.
ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished.
Notes on Ordering:
1. Find out the size of the prop nut you need.
2. If you need a different prop nut, you need to order it separately.
3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut.
Shiny Finish styles are considered "while supplies last", new style is brushed aluminum.
ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished.
Notes on Ordering:
1. Find out the size of the prop nut you need.
2. If you need a different prop nut, you need to order it separately.
3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut.
Shiny Finish styles are considered "while supplies last", new style is brushed aluminum.
Cut for reverse (counter rotating or pusher) prop. Light weight design made of high quality aluminum bar stock. Polished to mirror finish. Comes with 2.3, 3.2 and 4mm collets.
ProSpin spinners are made from high quality bar-stock for strength. They won't crack like cheap cast aluminum spinners do. ProSpin spinners are also 30% lighter than cast aluminum. All spinners include a shaft bushing, prop nut, and bolt. All spinners are polished.
Notes on Ordering:
1. Find out the size of the prop nut you need.
2. If you need a different prop nut, you need to order it separately.
3. Some engines, i.e. Saito engines, require a bushing that is larger than the nut.
Shiny Finish styles are considered "while supplies last", new style is brushed aluminum.
DISCONTINUED BY APC, LIMITED INVENTORY, WHILE SUPPLIES LAST
SKU Number: APC07477C
Discontinued RC Products and Parts
This category brings together items that are being retired from the regular Radical RC lineup, from older kits and power systems to individual replacement parts. It is worth a look for modelers keeping an aging airframe or motor system running, since parts for earlier generations of gear can be hard to track down elsewhere.
Kits and Power Systems
The mix includes complete projects such as the Hannibal Kit alongside power components like the GWS IPS Power System and the Astro Flight Firefly motor system with its planetary gearbox and small ESC.
Parts and Accessories
Smaller support items appear here too, including an LPS replacement spur gear, the Hansen Hobbies MERS micro electronic receiver and accessory switch, and a Mercury Adhesives caddy with adhesives. Because these are older or ending lines, the selection shifts as items move on.
Scan the listings below to see what is currently available.
 "Sig Monocoupe by Tom Stark")
 "Hitec FM 72mHz TX Crystals, New or Used")
 "Hitec HS-605BB Dual Ball Bearing Power Servo LAST ONE LEFT!")
 "Excel 5\" Stainless Scissors, WHILE SUPPLIES LAST!")
 "Kokam Lithium Polymer 3S 2000mAh 15C")
 "Kokam 3S, 12\" Balance Extension")
 "Kokam 4S, 12\" Balance Extension")
 "Kokam 5S, 12\" Balance Extension")
 "GWS 20mm Heat Sink / Adapter to S-300 Fan Housings")
 "GWS IPS Dual Motor - RXC Power System-AS")
 "GWS IPS Dual Motor - RXC Power System-BS")
 "GWS IPS Dual Motor - RXC Power System-CS")
 "GWS IPS Dual Motor - RXC Power System-DS")
 "GWS IPS Dual Motor - RXC Power System-ES")
 "GWS IPS Dual Motor - RXC Power System-FS")
 "K & S Pencil Soldering Iron 30W")
 "MPI 29mm (1.14\") E-Spinner Bar-Stock Aluminum Shiny Finish, LAST ONES!")
 "MPI 38mm (1.50\") E-Spinner Reverse Pitch Bar-Stock Aluminum Shiny Finish, LAST ONES!")
 "MPI 44mm (1.73\") E-Spinner Bar-Stock Aluminum Shiny Finish LAST ONES!")
 "MPI 50mm (1.97\") E-Spinner Bar-Stock Aluminum Shiny Finish, LAST 1 LEFT!")
 "MPI 29mm (1.14\") E-Spinner Reverse Pitch Bar-Stock Aluminum Shiny Finish, LAST ONES!")
 "Vintage Cox 3.125 x 2.5 - 3 Blade Prop")
 "Vintage Cox 5 x 3 Gray Series")
