$7 Minimum Shipping — USA Addresses See checkout for all options. Insurance automatically added to all USA orders over $50. $13 Minimum Shipping — All Phone Orders Worldwide shipping — see checkout for shipping options.
Handy set of 8 black nylon keepers. Fits .055" (1.5mm) push rod wire most commonly used in park fliers and foamys. Black nylon material. Simply bend the end of your pushrod into an "L". Put the L through the servo or control horn. Bend the hand back and clip onto the rod. Simple use, removes and instals quickly. Keeps your push rods from slipping out of the control horns. Light weight, simple and they work great!
Photo shows an example of our "Flexi-Keeper" hooked to end of push rod and a control horn.
Four barrels, washers, nuts and set screws. Allen wrench not included, requires 1.5mm. Will work on any rod size 1.5 to 1.85mm (.074"). 2mm pushrods and 2-56 are usually this size or smaller. The threads are rolled and larger than the base wire diameter. Instal in 5/64" (1.9mm) hole.
Four barrels, washers, nuts and set screws. Allen wrench not included, requires 1.5mm. Will work on any rod size 1.5 to 2mm (.079"). 2mm pushrods and 2-56 are usually this size or smaller. The threads are rolled and larger than the base wire diameter. Install in 7/64" (2.6mm) hole.
Handy set of 8 black nylon keepers. Fits .8128" (2mm) push rod wire most commonly used in park fliers and foamys. Black nylon material. Simply bend the end of your pushrod into an "L". Put the L through the servo or control horn. Bend the hand back and clip onto the rod. Simple use, removes and instals quickly. Keeps your push rods from slipping out of the control horns. Light weight, simple and they work great!
Photo shows an example of our "Flexi-Keeper" hooked to end of push rod and a control horn.
Control horn & wire are not included in set.
1st photo shows the .055" size with control horn for example, 2nd photo shows this part as cut.
SKU Number: RRCFLEXIKEEP02
1.5mm Rod Ends and Wire Keepers
At the servo and control-horn ends of a pushrod, a rod end or keeper holds the wire in place and lets you make fine adjustments to a linkage. This category groups the hardware sized for .055 inch, or 1.5mm, wire, along with a few related 2mm parts, so the small pieces that finish a linkage are gathered in one place.
L-Bend Keepers
When a pushrod wire is bent into an L at the control horn, a keeper slips over the bend to stop it working loose in flight. The GWS L-bend retainers and Radical RC Flexi-Keepers cover .055 inch (1.5mm) wire, and a Flexi-Keepers set for 2mm wire is offered as well, both supplied in 8-packs for stocking several linkages at once.
Adjustable Rod Ends
For a threaded, adjustable connection, the EZ-A-Just rod ends thread onto 1.5mm, 2mm, or 2-56 shafts, with standard and heavy-duty versions covering shafts up to roughly 1.8mm and 2mm. An adjustable end lets you fine-tune control throw without rebending the wire.
Match the keeper or rod end to your wire size, then choose from the listings here.
 "Radical RC Flexi-Keepers .055\" (1.5mm) Wire L Bends 8 Pack")
 "1.5mm/2mm/2-56 EZ-A-Just Rod Ends up to 1.8mm shafts")
 "1.5mm/2mm/2-56 Heavy Duty EZ-A-Just Rod End up to 2mm Shafts")
 "Radical RC Flexi-Keepers .81\" (2mm) Wire L Bends 8 Pack")
