|
| |
High Quality 5 Minute Epoxy. Use epoxy where a strong non-brittle bond is required. Firewalls, landing gear blocks, wing hold down bolt blocks, fuel proofing and on sensitive materials like foam. 5 minute epoxy is best for quick repairs and new model construction where lots of working time is not required. Hint! If you mix your epoxy on a flexible surface, like a paper plate you can go back to the mixture a week later and flex it. If it cracks easily then your not getting the portions mixed properly or failing to mix them enough. A good epoxy joint is very strong yet somewhat flexible. If the puddle of glue cracks it means it is hard like glass and not giving you the best qualities of the glue. Using a paper plate flex test is a good way to follow your own progress and improve your glue mixing skills. If your resin feels hardened inside the bottle, just warm it in the microwave for 10 seconds or so and you'll be good to go! WHILE SUPPLIES LAST! Learn about epoxy from an expert at RCModelReviews
SKU Number: PARB1504
|
|
|
|
|
| |
High Quality 5 Minute Epoxy. Use epoxy where a strong non-brittle bond is required. Firewalls, landing gear blocks, wing hold down bolt blocks, fuel proofing and on sensitive materials like foam. 5 minute epoxy is best for quick repairs and new model construction where lots of working time is not required. Hint! If you mix your epoxy on a flexible surface, like a paper plate you can go back to the mixture a week later and flex it. If it cracks easily then you're not getting the portions mixed properly or failing to mix them enough. A good epoxy joint is very strong yet somewhat flexible. If the puddle of glue cracks it means it is hard like glass and not giving you the best qualities of the glue. Using a paper plate flex test is a good way to follow your own progress and improve your glue mixing skills. If your resin feels hardened inside the bottle, just warm it in the microwave for 10 seconds or so and you'll be good to go! Note: Two, 2oz. bottles shown, but you get two 4oz. bottles in this size (4 oz. part A and 4 oz. part B = 8 total oz. of 5 min. epoxy). WHILE SUPPLIES LAST!
SKU Number: PARB1508
|
|
|
|
|
| |
High Quality 30 Minute Epoxy. Use epoxy where a strong non-brittle bond is required. Firewalls, landing gear blocks, wing hold down bolt blocks, fuel proofing and on sensitive materials like foam. 30 minute epoxy is best for quick repairs and new model construction where lots of working time is required. Also excellent for wetting out small fiber glass sections. Hint! Need your joint to cure a little faster? Take a covering heat shrink gun to the joint and warm it up. Be carefull, the heat will at first cause the epoxy to become thinner, it might run out of the joint and make a mess. Also, be warned! A little heat goes a long way and can cause your glue to dry faster than you had planned. You can also preheat the glue before applying to the parts or pre heat the parts. And, if your resin feels hardened inside the bottle, just warm it in the microwave for 10 seconds or so and you'll be good to go! WHILE SUPPLIES LAST! Learn about epoxy from an expert at RCModelReviews
SKU Number: PARB3004
|
|
|
|
|
| |
High Quality 30 Minute Epoxy. Use epoxy where a strong non-brittle bond is required. Firewalls, landing gear blocks, wing hold down bolt blocks, fuel proofing and on sensitive materials like foam. 30 minute epoxy is best for quick repairs and new model construction where lots of working time is required. Also excellent for wetting out small fiber glass sections.Hint! Need your joint to cure a little faster? Take a covering heat shrink gun to the joint and warm it up. Be carefull, the heat will at first cause the epoxy to become thinner, it might run out of the joint and make a mess. Also, be warned! A little heat goes a long way and can cause your glue to dry faster than you had planned. You can also preheat the glue before applying to the parts or pre heat the parts. And, if your resin feels hardened inside the bottle, just warm it in the microwave for 10 seconds or so and you'll be good to go! WHILE SUPPLIES LAST!
Learn about epoxy from an expert at RCModelReviews
SKU Number: PARB3008
|
|
|
|
|
| |
Super quick epoxy. This stuff does not mess around and you better be ready to go when you mix it up. fast field repairs possible for firewalls and landing gear blocks. Drys clear. Working time 90 seconds. Handling time 5 minutes. Full strength in 1 hour. Includes mixing nozzles. If not using all or most for a single repair, it is recommended to squeeze it out without the mixing nozzle. Mix and apply. .48 ounce contents.
SKU Number: SH336
|
|
|
|
|
| |
All purpose 5 minute epoxy in resealable 1 oz. applicator. Clear.
5 minute working time, 15 minutes hard. Easy flow syringe with snap open cap. Reseals for storage. TEMPORARILY OUT OF STOCK
SKU Number: DEVCONS-208
|
|
|
|
|
| |
8 ounces of Mercury's best. Great at bonding wood, fiberglass, foams and nearly all other types of materials. It achieves its great strength as a result of a chemical reaction when mixed with the hardening agent and does not shrink while curing. Don't forget mixing sticks and mixing cups available here.
SKU Number: MER5EPOXY8OZ
|
|
|
|
|
| |
8 ounces of Mercury's best. Great at bonding wood, fiberglass, foams and nearly all other types of materials. It achieves its great strength as a result of a chemical reaction when mixed with the hardening agent and does not shrink while curing. Don't forget mixing sticks and mixing cups available here.
SKU Number: MER15EPOXY8OZ
|
|
|
|
|
| |
8 ounces of Mercury's best. Great at bonding wood, fiberglass, foams and nearly all other types of materials. It achieves its great strength as a result of a chemical reaction when mixed with the hardening agent and does not shrink while curing. Don't forget mixing sticks and mixing cups available here.
SKU Number: MER30EPOXY8OZ
|
|
|
|
|
| |
Pot life (working time) is approximately 1-1/2 hours. Set time is 24 hours in a thin film. Use were extra working time and strength is needed. Note, amber tone in photo is because you are looking through 1" of material. Your much thinner applications will be clear or nearly so. Contents: 4 ounces
Working Time: Aprox. 1.5 hours
Cure Time: 24 hours
Color: Clear or slight amber tone
Other: Odorless, not brittle, sands easily, great for laminating wood to foam
SKU Number: SIGEG004
|
|
|
|
|
| |
Pot life (working time) is approximately 1-1/2 hours. Set time is 24 hours in a thin film. Use where extra working time and strength is needed. Note, amber tone in photo is because you are looking through 1" of material. Your much thinner applications will be clear or nearly so. Contents: 9 ounces
Working Time: Approx. 1.5 hours
Cure Time: 24 hours
Color: Clear or slight amber tone
Other: Odorless, not brittle, sands easily, great for laminating wood to foam
SKU Number: SIGEG009
|
|
|
|
|
| |
SLOW-CURE(TM) 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE(TM) can be used for bonding if you're willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE(TM) and FINISH-CURE(TM) to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.
Works Best On: - Glass & Metal
- Fiberglass
- White Foam
- Water-Resistant
- Reinforcing
Works Good On: - Balsa Wood
- Soft Wood
- Hard Wood
- Hard Plastics
- Laminating
DIRECTIONS: SLOW-CURE(TM) 30 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals. SLOW-CURE(TM) has the highest strength of our epoxies and should be applied in temperatures above 70°F. SLOW-CURE(TM) maintains its strength in both the lowest and highest temperature ranges of our line of epoxies. SLOW-CURE(TM) bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. SLOW-CURE(TM) works best for forming reinforcing fillets on joints and can be mixed with micro balloons or other fillers to form putty-like consistency. SLOW-CURE(TM) is waterproof and forms superior bonds if you're willing to wait overnight. It has better penetration of porous surfaces for better bonding. Full cure in 6-8 hours.
AVAILABLE SIZE:
BSI-205: 4.5 oz combined net wt. (128 g) BSI-206: 9 oz combined net wt. (256 g)
MADE IN THE USA
SKU Number: BSI205
|
|
|
|
|
| |
QUIK-CURE(TM) 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress.
QUIK-CURE(TM) shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats.
QUIKCURE(TM) is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE(TM) can be handled after 15 minutes. Full strength is reached in 1 hour.
Works Best On: Works Good On: - Balsa Wood
- Soft Wood
- Fiberglass
- Ceramics
- Hard Plastics
- White Foam
- Reinforcing
DIRECTIONS: QUIK-CURE(TM) 5 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals. QUIK-CURE(TM) is the least temperature sensitive of our epoxies. It will cure in temperatures down to 40°F. Temperatures above 90°F shorten the working time before the epoxy begins to set up from 5 to less than 4 minutes. QUIK-CURE(TM) bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. QUIK-CURE'S(TM) lack of brittleness allows it to form lasting bonds on materials as different as balsa wood and glass; however, it is not recommended for areas subject to long-term immersion in water. Cured QUIK-CURE(TM) can be coated with polyester resin without affecting the curing of the resin. Full cure in less than 15 minutes.
AVAILABLE SIZE: BSI-201: 4.5 oz combined net wt. (128 g)
BSI-202: 9 oz combined net wt. (256 g) MADE IN THE USA
SKU Number: BSI201
|
|
|
|
|
| |
8 ounce set of 5 Minute Z-POXY is a premium two part epoxy adhesive that dries clear. Vibration resistant and fuel proof, this epoxy is perfect for all types of hobbies and crafts. Excellent for furniture. It does not get brittle with age and its easy to mix, just combine equal parts by volume. Durable and sand-able.
SKU Number: PACPT38
|
|
|
|
|
| |
MID-CURE(TM) 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE(TM) in most applications.
MID-CURE(TM) is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.
Works Best On:
Works Good On: - Balsa Wood
- Soft Wood
- Glass & Metal
- Hard Plastics
- Rubber
- White Foam
- Laminating
- Water-Resistant
- Reinforcing
DIRECTIONS: MID-CURE(TM) 15 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals. MID-CURE(TM) should be applied in temperatures above 65?F. It can be used in most applications when you need more working time than QUIK-CURE(TM) provides. MID-CURE(TM) can be worked for about 10 minutes, with adhesion beginning after about 15 minutes. MID-CURE(TM) bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. MID-CURE(TM) is our most flexible epoxy. This gives it superior bonding qualities in applications such as hardwood to fiberglass. MID-CURE'S(TM) lack of brittleness allows it to form lasting bonds in areas subject to high vibration or stress. MID-CURE(TM) is a water-resistant substitute for QUIK-CURE(TM). Full cure in 2-3 hours.
AVAILABLE SIZE:
BSI-203: 4.5 oz combined net wt. (128 g)
BSI-204: 9 oz combined net wt. (256 g)
MADE IN THE USA
SKU Number: BSI203
|
|
|
|
|
| |
8 ounce set of 30 Minute Z-POXY is a premium two part epoxy adhesive that dries clear. Vibration resistant and fuel proof, this epoxy is perfect for all types of hobbies and crafts. Excellent for furniture. It does not get brittle with age and its easy to mix, just combine equal parts by volume. Durable and sand-able. Limited quantity, while supplies last!
SKU Number: PACPT39
|
|
|
|
 "PARBOND 5 Minute 4 Ounce Epoxy")
 "PARBOND 5 Minute 8 Ounce Epoxy")
 "PARBOND 30 Minute 4 ounce Epoxy")
 "PARBOND 30 Minute 8 ounce Epoxy")
 "ShurHold 90 Second Epoxy")
 "1 ounce Devcon 5 Minute Epoxy in Applicator")
 "Mercury 5 Minute Epoxy")
 "Mercury 15 Minute Epoxy")
 "Mercury 30 Minute Epoxy")
 "SIG 1-1/2 Hour Epoxy Glue 4 Ounce Kit")
 "SIG 1-1/2 Hour Epoxy Glue 9 Ounce Set")
 "Slow-Cure(TM) 30 Min. Epoxy")
 "Quik-Cure(TM) 5 Min. Epoxy")
 "Z-Poxy 5-Minute Epoxy by ZAP 8-Ounce Set")
 "Mid-Cure(TM) 15 Min. Epoxy")
 "Z-Poxy 30-Minute Epoxy by ZAP 8-Ounce Set")